Cisco Systems NME-16ES-1G specs

Cisco EtherSwitch Service Modules Feature Guide

Additional References

Cisco IOS Release 12.2(25)SEC

88

Image 88

Cisco Systems NME-16ES-1G manual

Contents

Guide Release Modification Contents Network Modules Hardware Installation Guide Hardware Overview Software Features and Benefits Ease-of-Use and Ease-of-Deployment Features Performance Features Management Options Manageability Features Availability Features Vlan Features Security Features QoS and CoS Features Power-over-Ethernet Features Monitoring Features Overview of Switch Stacks Cisco StackWise Concepts Switch Stack Membership Stack Master Election and Re-Election Switch Stack Bridge ID and Router MAC Address Stack Member Numbers Stack Member Priority Values Switch Stack Software Compatibility Recommendations Stack Protocol Version Compatibility Switch Stack Configuration Files Switch Stack Management Connectivity Clustering Concepts Accessing the CLI of a Specific Stack MemberManagement Connectivity to Specific Stack Members Standby Command Device Characteristics Command Device CharacteristicsCluster Compatibility Automatic Discovery of Candidates and Members Candidate and Member CharacteristicsDiscovery of Candidates and Members Through CDP Hops Vlan Discovery of Candidates and Members Through Different VLANs Switch Discovery of Candidates and Members Through Routed Ports Discovery of Newly Installed Switches in Clusters New out-of-box Hsrp and Standby Cluster Command Switches Virtual IP Addresses in Clusters Other Considerations for Cluster Standby Groups Automatic Recovery of Cluster Configuration IP Addresses in Clusters Hostnames in Clusters Passwords in Clusters Switch Clusters and Switch StacksSwitch Stack Switch Cluster Snmp Community Strings in Clusters Switch Stack Switch Cluster Availability of Switch-Specific Features in Switch Clusters TACACS+ and Radius in Clusters Cisco IOS Release 12.225SEC Using Interface Configuration Mode Command or Action Purpose Boot flash image-nameExample Dir flash Enable Show running configurationConfigure terminal Service-module interface slot/port session Show power inline Output of the show service-module status commandShow ip interface brief Control+shift+6 Sample Output for the dir flash Command on the Router Sample Output for the boot flash Command on the RouterRouter boot flashc2800-adventerprisek9-mz Examples Router# show running config interface gigabitethernet2/0 Router# configure terminalRouter# service-module gigabitethernet2/0 session Switch dir flash Switch# show ip interface brief Switch# ctrl+shift+6Switch# show power inline Sample Output for Pressing Ctrl+Shift+6 Followed by Feature Default Setting Dhcp STP Prerequisites Clustering Concepts section on Return Sample Output for Entering an Interface Name Sample Output for Assigning the IP Address and Subnet Mask Sample Output for Saving the Configuration to Nvram Command or Action Purpose Router# service-module gigabitethernet1/0 reset Router# service-module gigabitethernet1/0 shutdownRouter# service-module gigabitethernet1/0 reload Cisco IOS Release 12.225SEC Default Switch Stack Configuration Restrictions Assigning a Stack Member Number Sample Output for the switch renumber Command Sample Output for the reload slot CommandShow switch Switchconfig# switch 6 renumber Setting the Stack Member Priority Value Sample Output for the show switch Command Verifying Information About the Switch Stack Sample Output for the switch priority CommandSwitchconfig# switch 2 priority Switch show switch Switch# show platform stack-manager all Switchconfig# show switch neighbors Show switch stack-ports Rcommand Using the CLI to Manage Switch ClustersShow version Sample Output for the rcommand and show version Commands Sample Output for the show cluster members Command Choose View Refresh Choose Cluster Add to Cluster or Password Cluster member Creating a Cluster Standby Group Detailed Steps from the CLI Cluster standby-group HSRP-group-name Routing-redundancy No switchport Sample Output for the ping tftpserver Command Sample Output for the show flash Command Sample Output for the copy tftp flash CommandSwitch# show flash Switch# copy tftp flash Recovering from a Corrupted Software Image Using Xmodem Service-module interface slot/port password-reset Flashinit Service-module interface slot/port Password-resetFlashinit Control+6 Sample Output for the copy flash xmodem Command TroubleshootingRouter# copy flash xmodem Sample Output for the copy tftp xmodem Command Router# copy tftp xmodem Router# service-module gigabitethernet1/0 session Router# service-module gigabitethernet2/0 password-reset Recovering from a Lost or Forgotten Password Optional loadhelper filesystem/file-url Boot -x -v deviceimagename Enable secret passwordRename Copy flash Copy running-configuration startup-configuration Reload Optional set Service-module password-reset command Boot Example Sample Output for the set CommandSet Scenario Action Result Current-stack-member-number Renumber new-stack-member-number Network Configuration Examples Network Demands Suggested Design Methods Cost-Effective Wiring Closet Redundant Gigabit Backbone Cisco SoftPhone Software Gigabit servers POP Related Documents Technical AssistanceRelated Topic Document Title Description Link