Imager Product Specifications

Chapter 11

Product

Specifications

	Parameter	Specification


	Dimensions (Typical):
	Height	7.5”/190 mm
	Length	4.5”/115 mm
	Width	3.0”/75 mm
	Weight	11 ounces/312 g (without cable)

	Aimer:
	Illumination LEDs	626nm +30nm
	Aiming LEDs	526nm +30nm

	Image	VGA, 640x480 or VGA, 752x480
	Image	Binary, TIFF, or JPEG output.
		Binary, TIFF, or JPEG output.

	Skew Angle	ρ40 degrees

	Pitch Angle	ρ40 degrees

	Horizontal Velocity	2 inches (5 cm) per second

	Scan Contrast	45% minimum for Matrix codes, 37.5% mini-
	Scan Contrast	mum for all others
		mum for all others

	Voltage Requirements	4.5 - 14 VDC at imager
	Operating Current	Interlaced aiming mode : 470mA @5V
	(Maximum)	Concurrent aiming mode : 700 mA @5V
	Standby Current	Normal mode: 100 mA @5V
	(Maximum)	Low power mode : 55 mA @5V

Product Reference Guide

11-1

Page 183

Image 183

Datalogic Scanning 7000 manual Imager Product Specifications, Parameter Specification

Contents

Product Reference Guide Datalogic Scanning, Inc Table of Contents Data Editing Iii Imaging Commands Appendix a Symbologies PowerScan 7000 2D About This Manual Getting Started Resetting the Standard Product Defaults Standard Product Default SettingsManual Conventions Condition Yellow LED Beeper Table assume the feature is enabled. SeeLED and Beeper Indications Gramming information Condition Plug and Play Connecting the imager with an RS-232 Serial Port Connecting the imager with USB RS-232 InterfaceThis interface applies to USB compatible mod- els only IBM SurePos Symbology Suffix USB PC Keyboard or USB Macintosh Key- boardFace applies to your unit No extra configuration e.g., baud rate is neces- sary USB COM Port EmulationCTS/RTS Emulation ACK/NAK Mode Connecting the imager in Universal Key- board Wedge mode Cable Connector Faces Terminal ID Models Supported Terminals @ $ # = / ‘ \ ~ Keyboard Country Slovakia Spain Sweden Switzerland German Caps Lock Keyboard StyleTurkey F Turkey Q Regular Automatic Caps Lock Autocaps via NumLockEmulate External Keyboard Keyboard Modifiers Control + Ascii Mode On Control + Ascii Mode OffTurbo Mode On Turbo Mode Off Numeric Keypad Mode On Numeric Keypad Mode Off RS-232 Modifiers RS-232 Baud Rate300 600 1200 2400 4800 9600 19200 38400 57,600 115,200 RS-232 Word Length Data Bits, Stop Bits, and Parity RS-232 Receiver Time-Out RS-232 Receiver Time-Out RS-232 Handshaking Terminal Interfaces Good Read Indicators Image VGABeeper Good Read Low 1400 Hz Medium 2800 Hz High 3100 Hz Beeper Volume Good ReadBeeper Pitch Good Read Low Medium High Off Normal Beep Short Beep Beeper Duration Good ReadLED Good Read Number of Beeps Good Read Trigger Modes Good Read DelayUser-Specified Good Read Delay User-Specified Good Read Delay Manual Trigger, Low Power Low Power Time-Out TimerRead Time-Out Low Power Time-Out Scan Stand Mode Presentation ModeScan Stand Symbol LEDs On LEDs Off Presentation LED TimerHands Free Time-Out Presentation Sensitivity Hands Free Time-Out Double Read TimeoutUser-Specified Double Read Timeout User-Specified Double Read Timeout Off Low 50% High 100% LED Power Level Imager Time-Out Illumination LightsImager Time-Out Lights On Lights Off Milliseconds Aimer DelayUser-Specified Aimer Delay Delay Duration Aimer Modes Aimer Mode OffInterlaced Mode Concurrent Mode Off Concurrent Interlaced Centering Centering Decode Search Mode This search mode is the default settingFull Omnidirectional Advanced Linear Decoding Output Sequence OverviewRequire Output Sequence Quick Omnidirectional Output Sequence Editor To Add an Output SequenceThese options Discard Code 93 must be enabled to use this exampleOutput Sequence Examples Other Programming Selections SEQBLK62001141FF6A001242FF69001143FF Breakdown of the command line is shown below Required On/Not Required Off Enter Sequence Default Sequence No Read Multiple Symbols Print Weight Set Print Weight DefaultVideo Reverse Upright Rotate Clockwise Upside Down Rotate Counterclockwise Working Orientation Prefix/Suffix Overview Data Editing Points to Keep In Mind To Add a Prefix or Suffix To Add a Carriage Return Suffix to all Sym- bologies Example Add a Suffix to a specific symbologyAdd CR Suffix All Symbologies To Clear One or All Prefixes or Suffixes Prefix Selections Suffix SelectionsFunction Code Transmit Intercharacter, Interfunction, and Intermessage Delays Intercharacter DelayIntercharacter Delay Interfunction Delay User Specified Intercharacter DelayInterfunction Delay Delay Length Character to Trigger Delay Intermessage Delay Intermessage Delay Data Format Editor Introduction Data Formatting To Add a Data Format Wildcard for all terminal types isLength Data Format Editor Commands Send CommandsOther Programming Selections Move Commands Search CommandsMiscellaneous Commands Data Format On, Format Required Data Format EditorData Formatter Data Formatter Off Alternate Data Format Alternate Data Formats Symbologies Message Length Description Linear SymbologiesAll Symbologies All Symbologies On All Symbologies Off Codabar Check Character Codabar EnableCodabar Codabar Start/Stop Characters Codabar Codabar Concatenation Code 39 Start/Stop Characters Code 39 EnableCode Codabar Message Length Code 39 Message Length Code 39 Check Character Code 32 Pharmaceutical Paraf or Pharmacode Code 39 Append Full Ascii On Full Ascii Off Full Ascii Check Digit Interleaved 2 of 5 EnableInterleaved 2 Code 39 Code Interleaved 2 of 5 Message Length Code 93 Code Default All Code 93 SettingsCode 93 Enable Code 93 Message Length Code 2 of 5 Message Length Default All Code 2 of 5 SettingsCode 2 of 5 Enable Code 2 Iata Code 2 of 5 Message Length Default All Code Iata 2 of 5 SettingsIata Code 2 of 5 Enable Iata Code 2 Matrix 2 of 5 Message Length Matrix 2 of 5 EnableCode 11 Enable Matrix 2 Check Digits Required One Check Digit Two Check DigitsCode 11 Message Length Default All Code 128 Settings Code 128 EnableIsbt 128 Concatenation Code 128 Code Default All Telepen SettingsCode 128 Message Length Code 128 Code Telepen Output AIM Telepen Output Original Telepen OutputTelepen Message Length UPC-A Number System Default All UPC-A SettingsUPC-A Enable UPC-A Check Digit Transmit Required Not Required UPC-A AddendaDigit Addenda On Digit Addenda Off UPC-A Addenda Required UPC-E0 Expand Default All UPC-E SettingsWith Extended Coupon Code UPC-E0 On UPC-E0 Off UPC-E0 Addenda Required UPC-E0 Addenda SeparatorUPC-E0 Check Digit Transmit UPC-E0 Number System UPC-E0 AddendaUPC-E1 On UPC-E1 Off EAN/JAN-13 Addenda Default All EAN/JAN SettingsEAN/JAN-13 Enable EAN/JAN-13 Check Digit Transmit EAN/JAN-13 Addenda Required EAN/JAN-13 Addenda SeparatorIsbn Translate EAN/JAN-8 Addenda Default All EAN/JAN-8 SettingsEAN/JAN-8 Enable EAN/JAN-8 Check Digit Transmit EAN/JAN-8 Addenda Separator EAN/JAN-8 Addenda Required Default All MSI Settings MSI EnableMSI Check Character MSI Message Length Default All Plessey Code SettingsPlessey Code Enable Plessey Code RSS Limited RSS-14 EnableRSS Limited Enable RSS-14 RSS Expanded Message Length Default All RSS Expanded SettingsRSS Expanded Enable RSS Expanded B On No Limited B and Limited a On Limited B Off Default All PosiCode SettingsPosiCode a and B Enable PosiCode Codablock F Stacked SymbologiesCodablock F Enable Trioptic Code Code 16K Message Length Default All Code 16K SettingsCode 16K Enable Code 16K Default All Code 49 Settings Code 49 EnableCode 49 Message Length Symbologies Eanucc Composite Codes Eanucc Emulation UPC/EAN VersionUPC/EAN Version On UPC/EAN Version Off Eanucc Composite Code Message Length RSS Emulation Eanucc Emulation Off Tcif Linked Code 39 TLC39 Transmit Check Digit Don’t Transmit Check Digit Postal CodesPostnet Postnet Check Digit Transmit Planet Code Check Digit Transmit Planet Code British Post Canadian PostKix Netherlands Post China Post Default All China Post SettingsAustralian Post Japanese Post China Post Message Length China Post EnableDefault All Korea Post Settings Korea Post Korea Post Message Length Default All QR Code SettingsQR Code Korea Post QR Code Message Length Default All Data Matrix SettingsData Matrix QR Code Data Matrix Message Length Data Matrix EnableDefault All MaxiCode Settings MaxiCode MaxiCode Message Length MaxiCode EnableDefault All Aztec Code Settings Aztec Code Aztec Runes Aztec Code EnableEnable Runes Disable Runes Aztec Code Message Length Symbologies Image Snap Imgsnp Imaging Commands Imgsnp Modifiers Image Snap Imgsnp Imgshp Modifiers Image Ship Imgshp Image Ship Imgshp Imaging Commands Default = 0, or full image IMGSNP1P0L168W90%32D 3S ship every 3rd pixel, both horizontally and vertically Intelligent Signature Capture Negative Positive 0123456789IMGBOX40S0X70Y190W100H1R0F Imgbox Modifiers Intelligent Signature Capture Imgbox Imaging Commands Semi Font Currency Serial Number Money Default All OCR Settings OCR symbols can misread when scanned sideOCR Fonts Currency On Currency FontOCR-A On OCR-B On Semi Font On Micr E13 B FontSemi Font Micr E 13 B On Creating an OCR Template OCR Templates Us, Amount, and Dash Template CharactersTo Add an OCR Template Template Characters Ddd414243ddd hex codes for letters Character Match SequencesAdding Spaces Dddddddd Ddddddddtddddlldd 551 ABC Ddddddggg OCR User-Defined VariablesReading Multi-Row OCR 414243 OCRTMPddddddddrllllllll OCR Check CharacterOCRTMPdddddddd OCRTMPllllllll OCR Modulo 10 Check Character OCR Modulo 10 Check CharacterOCR Modulo 36 Check Character Dddddddc OCR User-Defined Check Character Programming a User-Defined Check Char- acter3031323334353637383958 Weighting Options Weighted Modulo 10 Check CharacterWeighted Modulo Check Character Ddddddc 0128454 OCR Isbn Application Example OCR Template Codes Save OCR Template Discard OCR Template Exit Selections OCR Programming To Add a Test Code I.D. Prefix to All Symbologies Show Software RevisionShow Data Format 2D PQA Print Quality Assessment Test Menu Power Image Configurator Operations Power Image Configurator Temporary Configuration Using Configura- tor Installing Power Image Configurator from the WebPower Image Configurator For RS-232 For USB Power Image Configurator Utilities Conventions Serial Programming Commands Query Commands Menu Command Syntax Responses Concatenation of Multiple CommandsTag Field Usage SubTag Field Usage Examples of Query Commands Trigger Commands Menu Commands Setting Serial SelectionIndicates default Slovakia SettingItaly Country Netherlands Dutch Auto Caps via Num Lock Keyboard Turbo Mode OffModifiers Turbo Mode On Keyboard Style Automatic Caps Lock Bits, and Parity Beeper Volume LowWord Length Data Bits, Stop Medium Delay 1000 ms Reread Delay Medium 750 msReread Delay No Delay Aimer Delay Off LED Power Level Low 50%Aimer Delay Milliseconds Off no delay Transmit Disable Print Weight Set Print WeightAdd CR Suffix to All Symbologies Function Code Enable Symbologies 5 Settings Interleaved 2 Off Default All CodeSettings Code Off Default All Interleaved Interleaved 2 Iata Code 2 Default All Code 2Settings Code 2 Off Settings Iata Code 2 Off Telepen Output AIM Telepen Output Settings Telepen OffMatrix 2 Off Tion UPC-A Check Off Default AllUPC-A Settings Coupon Code Default All UPC-E UPC-E0 Check Off Default All EANJAN Settings JAN 8 Settings Transmit Acter Validate Type 10 Default All RSS-14RSS-14 Settings Off Addenda Digit Addenda Off Expanded Settings RSS Expanded Off Default All RSS-14 RSS LimitedLimited Settings RSS Limited Off Default All RSS-14 RSS Expanded Eanucc Com Code OffMinimum 1-366 *1 Msg. Length Maximum 1-366 *366 Planet Code Transmit Postnet Check TransmitDigit Don’t Transmit Planet Code Length Maximum 1-3500 *3500 MaxiCode Default All MaxiCode SetAztec Runes Enable Runes QR Code Msg Minimum 1-3500 *1 Imaging Default Commands Compensation On Infinity Filter OffInfinity Filter On Compensation Off OCR Selections Char 456789456789ABCDE Acter OCR User-Defined Check 10-28 PowerScan 7000 2D Parameter Specification Imager Product Specifications 22θF to 122θ F -30θC to +50θ C Power SupplyTemperature Ranges Operating Noise Rejection Mechanical Shock Standard Cable Pinouts Primary Interface Cables Serial OutputPin RJ41 Modular Plug Pin Modular Plug Standard Cable Pinouts AIM Symbology Chart Code ID Symbology Trioptic Code QR/Micro QR CodeStop Tcif Linked Code 39 TLC39 Ascii Conversion Chart Code Ascii Conversion Chart Code PowerScan 7000 2D Code Page Mapping of Printed Bar Codes Code Page option is available for Code Code 93, and CodeStandard Description PowerScan 7000 2D Sample Symbols Data Matrix QR Code Sample Symbols Aztec Sample Symbols Save Discard OCR Programming Chart Programming Chart Programming Chart Programming Chart PowerScan 7000 2D Page Datalogic Scanning, Inc