Datalogic Scanning 7000 EAN/JAN-13

Symbologies

6-24 PowerScan® 7000 2D

EAN/JAN-13

EAN/JAN-13 Enable

EAN/JAN-13 Check Digit Transmit

This selection allows you to specify whether the check digit should be

transmitted at the end of the scanned data or not. Default = On.

EAN/JAN-13 Addenda

This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13

data.

Default = Off for both 2 Digit and 5 Digit Addenda.

* On

Off

* On

* 5 Digit Addenda Off

5 Digit Addenda On

* 2 Digit Addenda Off

2 Digit Addenda On

Contents

Main Page Product Reference Guide i Table of Contents Chapter 1 Getting Started.........................................................1-1 Chapter 2 Terminal Interfaces.................................................. 2-1 Chapter 3 Output...................................................................... 3-1 ii Chapter 4 Data Editing............................................................. 4-1 Chapter 5 Data Formatting....................................................... 5-1 Product Reference Guide iii Chapter 6 Symbologies............................................................. 6-1 iv Chapter 7 Imaging Commands................................................. 7-1 Chapter 8 OCR Programming ................................................... 8-1 Chapter 9 Utilities.................................................................... 9-1 Page Page Chapter 1 Getting Started About This Manual Manual Conventions Resetting the Standard Product Defaults LED and Beeper Indications Plug and Play Plug and Play bar codes provide instant imager set up for commonly used interfaces. Connecting the imager with an RS-232 Serial Port Connecting the imager with USB IBM SurePos USB PC Keyboard or USB Macintosh Key- board USB HID USB COM Port Emulation CTS/RTS Emulation ACK/NAK Mode Connecting the imager in Universal Key- board Wedge mode Page Chapter 2 Terminal Interfaces Terminal ID the digits (before scanning Save), scan the Discard code marked Discard code again. Supported Terminals Keyboard Country Page Keyboard Country (continued) Keyboard Style Page Keyboard Modifiers RS-232 Modifiers RS-232 Baud Rate RS-232 Word Length: Data Bits, Stop Bits, and Parity RS-232 Receiver Time-Out RS-232 Handshaking Page Chapter 3 Output Image VGA Good Read Indicators Beeper Good Read Beeper Volume Good Read Beeper Pitch Good Read Beeper Duration Good Read LED Good Read Number of Beeps Good Read Good Read Delay User-Specified Good Read Delay Trigger Modes Manual/Serial Trigger Read Time-Out Manual Trigger, Low Power Low Power Time-Out Timer Page Scan Stand Mode Scan Stand Symbol Presentation Mode Presentation LED Timer Presentation Sensitivity Hands Free Time-Out Double Read Timeout User-Specified Double Read Timeout LED Power Level Illumination Lights Imager Time-Out Aimer Delay User-Specified Aimer Delay Aimer Modes Aimer Mode Off Interlaced Mode Concurrent Mode Centering Page Decode Search Mode Output Sequence Overview Require Output Sequence Output Sequence Editor To Add an Output Sequence Other Programming Selections Output Sequence Examples Page Output Sequence Editor Require Output Sequence Multiple Symbols No Read Print Weight Video Reverse Working Orientation Chapter 4 Data Editing Prefix/Suffix Overview Points to Keep In Mind To Add a Prefix or Suffix: Repeat Steps 1-6 to add a prefix or suffix for another symbology. Example: Add a Suffix to a specific symbology To Clear One or All Prefixes or Suffixes: To Add a Carriage Return Suffix to all Sym- bologies Page Intercharacter, Interfunction, and Intermessage Delays Intercharacter Delay User Specified Intercharacter Delay Interfunction Delay Intermessage Delay Chapter 5 Data Formatting Data Format Editor Introduction To Add a Data Format Other Programming Selections Data Format Editor Commands Send Commands Data Formatting Move Commands Search Commands Miscellaneous Commands Data Format Editor Data Formatter Alternate Data Formats Chapter 6 Symbologies Linear Symbologies All Symbologies Message Length Description Page Page Code 39 Page Page Page Interleaved 2 of 5 Page Code 93 Code 2 of 5 IATA Code 2 of 5 Matr ix 2 of 5 Code 11 Page Code 128 Page Page UPC-A Page UPC-A/EAN-13 with Extended Coupon Code Page Page EAN/JAN-13 Page EAN/JAN-8 Page MSI Plessey Code Page RSS Expanded PosiCode Trioptic Code Stacked Symbologies Codablock F Code 16K Code 49 PDF417 MicroPDF417 EAN UCC Composite Codes UPC/EAN Version TCIF Linked Code 39 (TLC39) Postal Codes Postnet Planet Code Page Page Korea Post QR Code Data Matrix MaxiCode Aztec Code Page Page Chapter 7 Imaging Commands Image Snap - IMGSNP IMGSNP Modifiers Page Image Ship - IMGSHP IMGSHP Modifiers Page Page Page Page Intelligent Signature Capture - IMGBOX IMGBOX Modifiers Page Page Chapter 8 OCR Programming OCR Fonts OCR U.S. Currency Font Page OCR Templates Creating an OCR Template Template Characters To Add an OCR Template... 37680981 Character Match Sequences 551ABC983 Adding Spaces } 551 ABC 983 Stringing Together Multiple Formats (Creating Or Statements) 99028650 9902XZ50 OCR User-Defined Variables 654321ABC 654321BAC 654321CCC Reading Multi-Row OCR OCR Check Character OCR Modulo 10 Check Character OCR Modulo 36 Check Character OCR User-Defined Check Character 6512351X Programming a User-Defined Check Char- acter Weighting Options 01234565 Page OCR ISBN Application Example OCR Template Codes Page Page Chapter 9 Utilities Resetting the Standard Product Defaults Test Menu 2D PQA (Print Quality Assessment) Power Image Configurator Power Image Configurator Operations Temporary Configuration Using Configura- tor Installing Power Image Configurator from the Web Page Page Chapter 10 Serial Programming Commands Serial Programming Commands Conventions Menu Command Syntax Query Commands ^ ? * Tag Field Usage SubTag Field Usage Data Field Usage Concatenation of Multiple Commands Responses Examples of Query Commands Trigger Commands Menu Commands Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Chapter 11 Product Specifications Imager Product Specifications at a distance of 19 (50cm) - typical Standard Cable Pinouts (Primary Interface Cables) Product Reference Guide 11-3 Standard Cable Pinouts (Primary Interface Cables) Serial Output 10 Pin RJ41 Modular Plug Product Specifications 11-4 PowerScan 7000 2D Standard Cable Pinouts USB UKBW 10 Pin Modular Plug Appendix A Symbologies Symbology Chart Page Page A-4 PowerScan 7000 2D ASCII Conversion Chart (Code Page 1252 ) ASCII Conversion Chart (Code Page 1252) Users Guide A-5 A-6 PowerScan 7000 2D Code Page Mapping of Printed Bar Codes Page Appendix B Sample Symbols Sample Symbols Sample Symbols OCR Programming Chart Page Programming Chart