Supported Terminals, Models | Datalogic Scanning 7000 manual

Terminal Interfaces

For example, an IBM AT terminal has a Terminal ID of 003. You would scan the Terminal ID bar code, then 0, 0, 3 from the Programming Chart on page B-5 of this manual, then Save. If you make an error while scanning the digits (before scanning Save), scan the Discard code marked Discard on page B-4, scan the Terminal ID bar code, scan the digits, and the Save code again.

Terminal ID

Save

After scanning one of these codes, you must power cycle your computer.

NOTE

Supported Terminals

Terminal	Model(s)	Terminal ID
IBM SurePOS	USB Hand Held Imager	128a
IBM SurePOS	USB Tabletop Imager	129a
RS-232 True		000b
RS-232 TTL		000
Serial Wedge		050
USB COM Port Emulation		130a
USB PC Keyboard		124a
USB Mac Keyboard		125a
USB HID POS		131a

a.Applies to USB models only. It is best to use the Plug and Play bar codes located in the Quick Reference Guide, to program these inter- faces, rather than scanning the terminal ID listed in this table.

b.Default for RS-232 models

2-2	PowerScan® 7000 2D

Image 20

Datalogic Scanning 7000 manual Supported Terminals, Models

Contents

Product Reference Guide Datalogic Scanning, Inc Table of Contents Data Editing Iii Imaging Commands Appendix a Symbologies PowerScan 7000 2D Getting Started About This Manual Manual Conventions Resetting the Standard Product DefaultsStandard Product Default Settings Table assume the feature is enabled. See LED and Beeper IndicationsGramming information Condition Condition Yellow LED Beeper Connecting the imager with an RS-232 Serial Port Plug and Play This interface applies to USB compatible mod- els only Connecting the imager with USBRS-232 Interface IBM SurePos Face applies to your unit Symbology SuffixUSB PC Keyboard or USB Macintosh Key- board CTS/RTS Emulation No extra configuration e.g., baud rate is neces- saryUSB COM Port Emulation Connecting the imager in Universal Key- board Wedge mode ACK/NAK Mode Cable Connector Terminal ID Faces Supported Terminals Models Keyboard Country @ $ # = / ‘ \ ~ Slovakia Spain Sweden Switzerland German Keyboard Style Turkey F Turkey QRegular Caps Lock Emulate External Keyboard Automatic Caps LockAutocaps via NumLock Control + Ascii Mode On Control + Ascii Mode Off Turbo Mode On Turbo Mode OffNumeric Keypad Mode On Numeric Keypad Mode Off Keyboard Modifiers 300 600 1200 2400 4800 9600 19200 38400 57,600 115,200 RS-232 ModifiersRS-232 Baud Rate RS-232 Word Length Data Bits, Stop Bits, and Parity RS-232 Receiver Time-Out RS-232 Receiver Time-Out RS-232 Handshaking Terminal Interfaces Beeper Good Read Good Read IndicatorsImage VGA Beeper Volume Good Read Beeper Pitch Good ReadLow Medium High Off Low 1400 Hz Medium 2800 Hz High 3100 Hz Beeper Duration Good Read LED Good ReadNumber of Beeps Good Read Normal Beep Short Beep Good Read Delay User-Specified Good Read DelayUser-Specified Good Read Delay Trigger Modes Read Time-Out Manual Trigger, Low PowerLow Power Time-Out Timer Low Power Time-Out Scan Stand Symbol Scan Stand ModePresentation Mode Presentation LED Timer Hands Free Time-OutPresentation Sensitivity LEDs On LEDs Off Double Read Timeout User-Specified Double Read TimeoutUser-Specified Double Read Timeout Hands Free Time-Out LED Power Level Off Low 50% High 100% Illumination Lights Imager Time-OutLights On Lights Off Imager Time-Out Aimer Delay User-Specified Aimer DelayDelay Duration Milliseconds Aimer Mode Off Interlaced ModeConcurrent Mode Aimer Modes Centering Off Concurrent Interlaced Centering Full Omnidirectional Decode Search ModeThis search mode is the default setting Output Sequence Overview Require Output SequenceQuick Omnidirectional Advanced Linear Decoding These options Output Sequence EditorTo Add an Output Sequence Code 93 must be enabled to use this example Output Sequence ExamplesOther Programming Selections Discard Breakdown of the command line is shown below SEQBLK62001141FF6A001242FF69001143FF Enter Sequence Default Sequence Required On/Not Required Off Multiple Symbols No Read Video Reverse Print WeightSet Print Weight Default Working Orientation Upright Rotate Clockwise Upside Down Rotate Counterclockwise Data Editing Prefix/Suffix Overview Points to Keep In Mind To Add a Prefix or Suffix Example Add a Suffix to a specific symbology Add CR Suffix All SymbologiesTo Clear One or All Prefixes or Suffixes To Add a Carriage Return Suffix to all Sym- bologies Function Code Transmit Prefix SelectionsSuffix Selections Intercharacter Delay Intercharacter, Interfunction, and Intermessage DelaysIntercharacter Delay User Specified Intercharacter Delay Interfunction DelayDelay Length Character to Trigger Delay Interfunction Delay Intermessage Delay Intermessage Delay Data Formatting Data Format Editor Introduction Length To Add a Data FormatWildcard for all terminal types is Other Programming Selections Data Format Editor CommandsSend Commands Miscellaneous Commands Move CommandsSearch Commands Data Format Editor Data FormatterData Formatter Off Data Format On, Format Required Alternate Data Formats Alternate Data Format Symbologies Linear Symbologies All SymbologiesAll Symbologies On All Symbologies Off Message Length Description Codabar Enable CodabarCodabar Start/Stop Characters Codabar Check Character Codabar Concatenation Codabar Code 39 Enable CodeCodabar Message Length Code 39 Start/Stop Characters Code 39 Check Character Code 39 Message Length Code 39 Append Code 32 Pharmaceutical Paraf or Pharmacode Full Ascii Full Ascii On Full Ascii Off Interleaved 2 of 5 Enable Interleaved 2Code 39 Code Check Digit Interleaved 2 of 5 Message Length Default All Code 93 Settings Code 93 EnableCode 93 Message Length Code 93 Code Default All Code 2 of 5 Settings Code 2 of 5 EnableCode 2 Code 2 of 5 Message Length Default All Code Iata 2 of 5 Settings Iata Code 2 of 5 EnableIata Code 2 Iata Code 2 of 5 Message Length Matrix 2 of 5 Enable Code 11 EnableMatrix 2 Matrix 2 of 5 Message Length Code 11 Message Length Check Digits RequiredOne Check Digit Two Check Digits Isbt 128 Concatenation Default All Code 128 SettingsCode 128 Enable Default All Telepen Settings Code 128 Message LengthCode 128 Code Code 128 Code Telepen Message Length Telepen OutputAIM Telepen Output Original Telepen Output Default All UPC-A Settings UPC-A EnableUPC-A Check Digit Transmit UPC-A Number System UPC-A Addenda Digit Addenda On Digit Addenda OffUPC-A Addenda Required Required Not Required Default All UPC-E Settings With Extended Coupon CodeUPC-E0 On UPC-E0 Off UPC-E0 Expand UPC-E0 Check Digit Transmit UPC-E0 Addenda RequiredUPC-E0 Addenda Separator UPC-E1 On UPC-E1 Off UPC-E0 Number SystemUPC-E0 Addenda Default All EAN/JAN Settings EAN/JAN-13 EnableEAN/JAN-13 Check Digit Transmit EAN/JAN-13 Addenda Isbn Translate EAN/JAN-13 Addenda RequiredEAN/JAN-13 Addenda Separator Default All EAN/JAN-8 Settings EAN/JAN-8 EnableEAN/JAN-8 Check Digit Transmit EAN/JAN-8 Addenda EAN/JAN-8 Addenda Required EAN/JAN-8 Addenda Separator MSI Check Character Default All MSI SettingsMSI Enable Default All Plessey Code Settings Plessey Code EnablePlessey Code MSI Message Length RSS-14 Enable RSS Limited EnableRSS-14 RSS Limited Default All RSS Expanded Settings RSS Expanded EnableRSS Expanded RSS Expanded Message Length Default All PosiCode Settings PosiCode a and B EnablePosiCode B On No Limited B and Limited a On Limited B Off Stacked Symbologies Codablock F EnableTrioptic Code Codablock F Default All Code 16K Settings Code 16K EnableCode 16K Code 16K Message Length Code 49 Message Length Default All Code 49 SettingsCode 49 Enable Symbologies Eanucc Composite Codes UPC/EAN Version UPC/EAN Version On UPC/EAN Version OffEanucc Composite Code Message Length Eanucc Emulation Tcif Linked Code 39 TLC39 RSS Emulation Eanucc Emulation Off Postal Codes PostnetPostnet Check Digit Transmit Transmit Check Digit Don’t Transmit Check Digit Planet Code Planet Code Check Digit Transmit Kix Netherlands Post British PostCanadian Post Default All China Post Settings Australian PostJapanese Post China Post China Post Enable Default All Korea Post SettingsKorea Post China Post Message Length Default All QR Code Settings QR CodeKorea Post Korea Post Message Length Default All Data Matrix Settings Data MatrixQR Code QR Code Message Length Data Matrix Enable Default All MaxiCode SettingsMaxiCode Data Matrix Message Length MaxiCode Enable Default All Aztec Code SettingsAztec Code MaxiCode Message Length Aztec Code Enable Enable Runes Disable RunesAztec Code Message Length Aztec Runes Symbologies Imaging Commands Image Snap Imgsnp Imgsnp Modifiers Image Snap Imgsnp Image Ship Imgshp Imgshp Modifiers Image Ship Imgshp Imaging Commands Default = 0, or full image 3S ship every 3rd pixel, both horizontally and vertically IMGSNP1P0L168W90%32D IMGBOX40S0X70Y190W100H1R0F Intelligent Signature CaptureNegative Positive 0123456789 Imgbox Modifiers Intelligent Signature Capture Imgbox Imaging Commands Currency Serial Number Money Semi Font OCR Fonts Default All OCR SettingsOCR symbols can misread when scanned side Currency Font OCR-A OnOCR-B On Currency On Micr E13 B Font Semi FontMicr E 13 B On Semi Font On OCR Templates Creating an OCR Template Template Characters To Add an OCR TemplateTemplate Characters Us, Amount, and Dash Character Match Sequences Adding SpacesDddddddd Ddd414243ddd hex codes for letters 551 ABC Ddddddddtddddlldd OCR User-Defined Variables Reading Multi-Row OCR414243 Ddddddggg OCR Check Character OCRTMPddddddddOCRTMPllllllll OCRTMPddddddddrllllllll OCR Modulo 10 Check Character OCR Modulo 36 Check CharacterDddddddc OCR Modulo 10 Check Character 3031323334353637383958 OCR User-Defined Check CharacterProgramming a User-Defined Check Char- acter Weighted Modulo Check Character Weighting OptionsWeighted Modulo 10 Check Character 0128454 Ddddddc OCR Isbn Application Example OCR Template Codes Exit Selections Save OCR Template Discard OCR Template OCR Programming Show Data Format To Add a Test Code I.D. Prefix to All SymbologiesShow Software Revision Test Menu 2D PQA Print Quality Assessment Power Image Configurator Power Image Configurator Operations Power Image Configurator For RS-232 For USB Temporary Configuration Using Configura- torInstalling Power Image Configurator from the Web Power Image Configurator Utilities Serial Programming Commands Conventions Menu Command Syntax Query Commands Concatenation of Multiple Commands Tag Field UsageSubTag Field Usage Responses Examples of Query Commands Trigger Commands Indicates default Menu CommandsSetting Serial Selection Setting ItalyCountry Netherlands Dutch Slovakia Keyboard Turbo Mode Off Modifiers Turbo Mode OnKeyboard Style Automatic Caps Lock Auto Caps via Num Lock Beeper Volume Low Word LengthData Bits, Stop Bits, and Parity Reread Delay Medium 750 ms Reread DelayNo Delay Medium Delay 1000 ms LED Power Level Low 50% Aimer Delay MillisecondsOff no delay Aimer Delay Off Print Weight Set Print Weight Add CR Suffix to All SymbologiesFunction Code Enable Transmit Disable Symbologies Default All Code Settings Code OffDefault All Interleaved Interleaved 2 5 Settings Interleaved 2 Off Default All Code 2 Settings Code 2 OffSettings Iata Code 2 Off Iata Code 2 Settings Telepen Off Matrix 2 OffTion Telepen Output AIM Telepen Output Default All UPC-A SettingsCoupon Code Default All UPC-E UPC-A Check Off Default All EAN JAN SettingsJAN 8 Settings UPC-E0 Check Off Default All RSS-14 RSS-14 Settings OffAddenda Digit Addenda Off Transmit Acter Validate Type 10 Default All RSS-14 RSS Limited Limited Settings RSS Limited OffDefault All RSS-14 RSS Expanded Expanded Settings RSS Expanded Off Code Off Minimum 1-366 *1Msg. Length Maximum 1-366 *366 Eanucc Com Postnet Check Transmit Digit Don’t TransmitPlanet Code Planet Code Transmit MaxiCode Default All MaxiCode Set Aztec Runes Enable RunesQR Code Msg Minimum 1-3500 *1 Length Maximum 1-3500 *3500 Imaging Default Commands Infinity Filter Off Infinity Filter OnCompensation Off Compensation On OCR Selections 456789 456789ABCDEActer OCR User-Defined Check Char 10-28 PowerScan 7000 2D Imager Product Specifications Parameter Specification Power Supply Temperature Ranges OperatingNoise Rejection Mechanical Shock 22θF to 122θ F -30θC to +50θ C Pin RJ41 Modular Plug Standard Cable Pinouts Primary Interface CablesSerial Output Standard Cable Pinouts Pin Modular Plug Symbology Chart AIM Symbology Code ID QR/Micro QR Code StopTcif Linked Code 39 TLC39 Trioptic Code Ascii Conversion Chart Code Ascii Conversion Chart Code PowerScan 7000 2D Standard Description Code Page Mapping of Printed Bar CodesCode Page option is available for Code Code 93, and Code PowerScan 7000 2D Sample Symbols Sample Symbols Data Matrix QR Code Sample Symbols Aztec OCR Programming Chart Save Discard Programming Chart Programming Chart Programming Chart PowerScan 7000 2D Page Datalogic Scanning, Inc