On-Demand Dispensing | Datamax 4406, 4212, 4604, 4308, 4208 instruction

3.5.2On-Demand Dispensing

When equipped with the Peel and Present option, labels are dispensed then separated automatically from the liner for immediate application.

n With the Peel and Present Mechanism installed on the printer, pull outward on the Latch and allow the Roller Bracket to swing forward.

o With media loaded as described in Section 3.1, press the FEED Key to advance approximately 20 inches (51 cm) of media. Remove all of the labels from the backing material.

pRoute the backing material through the Roller Bracket as shown (the backing should go under the top black roller, then out).

qRaise the Roller Bracket up to its latched position.

26

I-Class

Image 36

Datamax 4406, 4212, 4604, 4308, 4208 manual On-Demand Dispensing

Contents

Operator’s Manual Page Copyright Information Firmware Software Agreement Agency Compliance and Approvals Page Important Safety Instructions Contents Using the Front Panel Troubleshooting Appendix E Printer Overview About the Printer Standard Features Class Standard Features Listing Model DMXNet Ilpc CG Times Firmware Present Sensor Option Installation Ilpc Hardware Components Class Getting Started Unpacking the Printer Inspection Additional Requirements Media and Ribbon Selection Print Quality Controls Direct Thermal Media Type Print Speed Print Energy Setting Up the Printer Installation Communications Parallel PortSerial Port Part Number NIC Adapter optional USB Port optional Loading Media Roll Media Fan-Fold Media Media Sensor Adjustment Media Sensor Selection and AdjustmentMedia Type Sensor Eye Mark Position Sensing Required Loading Ribbon Removal Ribbon Routing Diagrams Quick Media Calibration Calibration Hints Outputting Labels Rewinding Removal On-Demand Dispensing Removal Cutting Using the Front Panel Operation Menu Mode Configuration Ready Light ‘Flashing’ Quick Test Mode Print Test Labels Indicator Lights 5 LCDLiquid Crystal Display Resetting the Printer Soft Reset Menu System Menu Mode Entrance and Exit Prompts Media Settings Print Control Custom Adjustments Printer Options ModulesPresent Sensor Cutter Scanner Used to set the specific number of barcodes Gpio Port System Settings Double Byte Symbols Print ConfigurationTime and Date Media Counters Configuration Level SET Factory Defaults Imaging ModeFormat Attributes Pause Mode Peel ModeInput Mode Security Plus Emulation Allegro Emulation DPI Emulation Column Emulation SOP EmulationBack After Print Fault Handling Menu Language Distance to backup on the defective Serial Port a Serial Port B Parallel Port a Parallel Port BNIC Adapter Specifies the network gateway address Host Settings Allows the user to disable the DPL Heat Diagnostics HEX Dump ModeOptions Testing Print Test Rate Sensor Readings Ribbon Sensor Limits Display Messages User Prompts and Condition Messages Reset in PROGRESS’ Quick Test Mode Print Quality Label Configuration Label Quick Ribbon Test Label Dot Test Pattern Label Validation Label User Defined Label Media Sensor Calibration Standard CalibrationStep Operator Action Displayed Message Comment Standard Calibration Notched stock adjust Reflective stock AdjustDie-cut stock strip Continuous stock go to Or, for continuous media Advanced Entry Calibration As a Label Value Value Both sensor Readings mustBe above Values Using Key Selection is Select the Gain Number Press Key Selection Printhead Adjustments Leveling Cam Adjustment Burn Line Adjustment Printhead Replacement Maintenance Schedule Recommended Cleaning Schedule Area Method Interval Cleaning the Printhead Cleaning the Platen Roller Application Program Updates Cleaning Interior and Exterior Surfaces Updating from the Ready Mode Updating from the Download Mode Possible Problems during an Update Boot Loader Program Updates Can be found at ftp//ftp.datamaxcorp.com Class Troubleshooting Problem ResolutionIf experiencing this problem… Try this solution… If experiencing this problem… Try this solution… If there is an image on the used ribbon If there is no image on the used ribbon I & W Class Programmer’s Manual for Fault and Warning Messages Fault Messages ENB!GBVMU Two possible Depending upon the cause Consistently high Press any key to continue Linear Scanner Operation Instructions, or call for If media is moving If media is not moving DMX Printer has Possible low or fluctuating Hex Dump Mode 102 Class General Specifications Bar CodesFonts Electrical Printing Specifications Environmental RequirementsMechanical Printing Specifications Media and Ribbon Requirements Media Dimensions Designator Description Maximum Minimum Approved Media Ascii Control Code Chart Appendix a Ascii Control Code Chart Appendix B Available Fonts and Bar CodesFont Valid Ascii Characters Font Height Width Spacing Page Page Symbology Bar Code Summary Data Bar Code F EAN-13 Bar Code K Plessey Bar Code p Postnet Bar Code O Code Bar Code T Telepen Print Resolutions and Maximum Label Widths Appendix CModule Assignments Inches Millimeters Available Speeds and Default Settings Printer Speed Ranges and DefaultsSpeed Range Default Setting Model Gpio Pin Functions Signal Description Name State Direction Appendix DGpio Port Description Gpio Port Connections Gpio Pin Configuration Gpio Port SpecificationsExternal Start of Print Control Appendix E Menu System Multi-Language SupportRequired Software Comment Page Page Menu Language Error Message Description Advance File Handling InformationPage 126 Class Saving a Configuration File Appendix F Step Displayed Message Operator Action Comments Warranty Information Printer Warranty Service Procedures Thermal Printhead, Platen Roller, and Belts General Warranty Provisions Limitation of Liability 132 Class Glossary Page