Installing on a Wall | Dell 28XX instruction

Installing on a Wall

To mount the device on a wall:

1Ensure that the mounting location meets the following requirements:

•The surface of the wall must be capable of supporting the device.

•Allow at least 2 inches (5.1 cm) space on the sides for proper ventilation and 5 inches (12.7 cm) at the back for power cable clearance.

•The location must not be exposed to direct sunlight.

•The location must be at least 2 feet (61 cm) away from any heating vents, and no area-heating vent should point towards the device.

•The location must be ventilated to prevent heat buildup.

•Do not locate the device near any data or electrical cabling.

•The power cable must be able to reach an outlet.

2Place the supplied wall-mounting bracket on one side of the device, ensuring that the mounting holes on the device line up to the mounting holes on the rack-mounting bracket. The following figure illustrates where to mount the brackets.

Figure 3-2. Bracket Installation for Wall Mounting

3Insert the supplied screws into the rack-mounting holes and tighten with a screwdriver.

4Repeat the process for the wall-mounting bracket on the other side of the device.

5Place the device on the wall in the location where the device is being installed.

Dell PowerConnect 28xx Systems User Guide

31

Image 31

Dell 28XX manual Installing on a Wall, Bracket Installation for Wall Mounting

Contents

User Guide March 4 Contents Installing the PowerConnect Device Using Dell OpenManage Switch Administrator Manually Allocating IP Addresses Static Hosts 144 169 System Description PowerConnect PowerConnect 2816 Front Panel Summary of PowerConnect Models FeaturesGeneral Features AutoMDI/MDIX Support Virtual Cable Testing VCTAuto Negotiation Jumbo Frames Support Layer 2 Features MAC Address Supported Features Vlan Supported Features Spanning Tree Protocol Features Ethernet Switch Management Features Class of Service CoS Features PowerConnect 28xx Front and Back Panel Port Description Switch Port Configurations PowerConnect 2808 Back Panel PowerConnect 2824 Front Panel PowerConnect 2824 Back Panel LED Definitions Physical Dimensions Port LEDs Power LEDManaged Mode LED Fan LED 2824/2848 only Switch Ventilation Fan Managed Mode ButtonSFP Port LED 1000BASE-T Cable Requirements Cables, Port Connections, and Pinout InformationRJ-45 Connections for 10/100/1000BASE-T Ports SFP Pin Connections Pin No Use SFP Ports Internal Power Supply Connector Power Connectors Installation Precautions Installing the PowerConnect Device Unpacking the Device Package ContentsSite Requirements Unpacking Mounting the Device Device Rack InstallationOverview Bracket Installation for Rack Mounting Installing on a Flat Surface Bracket Installation for Wall Mounting Installing on a Wall Mounting Device on a Wall Connecting the Device to the Network Connecting the DeviceConnecting the Terminal to the Device Connecting a Device to a Power Supply RJ-45 Connections for 10/100/1000BaseT Ports Port Connections, Cables, and Pinout Information Ports, Connectors and Cables Port/Interface Back Pressure Port Default SettingsAuto-Negotiation Flow Control Following table gives the port default settings Switching Port Default Settings 43+ Enter Wizard Management Modes Unmanaged Mode In this mode Transitioning Between Management Modes Transitioning Between Modes Restore Saved Configuration Initial Configuration Through the Set-up Wizard Booting the Device Managed Mode Welcome to Dell Easy Setup Wizard Wizard Step Wizard Step Basic Configuration Initial Configuration Through the Web Web management IP Interface Parameters Retrieving an IP Address From a Dhcp Server Startup Menu Software Download Erasing the Device ConfigurationErase Flash File Software Download Through Tftp Server Password RecoverySystem Image Download Boot Image Download Understanding the Interface Using Dell OpenManage Switch Administrator Information Buttons Using the Switch Administrator Buttons Starting the Application Access LevelsDevice Management Buttons Dell PowerConnect 28xx Systems User Guide Viewing Device Information Defining General Device Information Asset Defining System Information Click Apply Changes Viewing the VersionsInitiating a Telnet Session Resetting the Device Resetting the Device Entering Secure Mode Entering Secure Mode Defining Device IP Addresses Setting static IP Interface parametersDefining IP Interface Parameters Viewing Copper Cable Diagnostics Running Cable DiagnosticsNo Cable Displaying Virtual Cable Test Results Table Viewing Optical Transceiver DiagnosticsPerforming a Cable Test Open the Integrated Cable Test Click Test Now Optical Transceiver Diagnostics Open the Optical Transceiver Diagnostics Click Show All LOSLoss of Signal Loss of signal TXTransmitter Fault Transmitter fault Defining the Local User Databases Password 0-64 Characters User-defined passwordAssigning Access Rights to a User Managing Device Security Displaying the Local User Table Defining a New User Deleting Users Configuring Radius Global Parameters Add Radius Server page opens Open the Radius SettingsDefining Radius Parameters Adding a Radius Server Displaying the Radius Server List Modifying the Radius Server Settings Deleting a Radius Server for the Radius Servers List Defining Snmp Parameters Defining Snmp Global Parameters Enabling Authentication NotificationsEnabling Snmp Notifications Add Snmp Community page opens Defining CommunitiesDefining a New Community Open the Snmp Community Deleting Communities Displaying all Communities 19. Notification Recipients Defining Snmp Notification Recipients Displaying Notification Recipients Tables Adding a new Trap RecipientsOpen Notification Recipients Add Notification Recipients page opens Downloading Files Managing Files 21. File Download From Server Firmware Download Open the File Download From Server Configuration DownloadUploading Files Downloading Files Open the File Upload to Server Restoring Default SettingsRestoring Default Settings Uploading Files Configuring Dhcp Properties Defining Dhcp Server Settings→ Dhcp Server → Dhcp Server Properties in the tree view 24. Dhcp Server Properties Enabling the Dhcp Server Defining Network Pool Click Apply Changes. The server is enabled Excluding Addresses Open the Excluded Addresses Adding an Excluded AddressDeleting Excluded Addresses 28. Static Hosts Manually Allocating IP Addresses Static Hosts Adding a new Static Host Domain Name- SpecifiesAdd Static Host page opens Click Show All Static Hosts Table page opens Displaying Static Hosts Tables Deleting Static Hosts Address Binding Configuring General Device Parameters Defining Advanced Settings Port Based Authentication Configuring Network SecurityAdvanced Port Based Authentication → Port Based Authentication Configuring Port Based Authentication Displaying the Port Based Authentication Table Select an interface in the Port Based Authentication Table Copying Parameters in the Port Based Authentication Table Multiple Hosts Configuring Advanced Port Based Authentication Multiple Hosts Table Displaying the Multiple Hosts Table Displaying the Authenticated Users Table Authenticating UsersClick Show All Authenticated Users Table opens 100 Authenticated Users Table Defining Port Parameters Configuring Ports101 102 Modifying Port Parameters Displaying the Port Configuration TableAggregating Ports Defining Port Parameters 104 LAG Configuration Modifying LAG Parameters Open the LAG ConfigurationCurrent Flow Control Defining LAG Parameters Displaying the LAG Configuration Table Configuring Green Ethernet106 107 11. Green Ethernet Configuration 108 Open the Green Ethernet ConfigurationEnabling Storm Control Enabling Green Ethernet on the Device 109 Enabling Storm Control on the DeviceDisplaying the Storm Control Table Click Show All Storm Control Table opens 110 Defining Port Mirroring Sessions 111 Adding a Port Mirroring SessionOpen the Port Mirroring Add Source Port page opens 112 Configuring Address TablesViewing Dynamic Addresses Deleting a Copy Port from a Port Mirroring Session Open the Dynamic Address Table Redefining the Aging Time113 Sorting the Dynamic Address Table Configuring the Spanning Tree ProtocolDefining STP Global Settings Querying the Dynamic Address Table 115 16. STP Global Settings Modifying STP Global Parameters Open the STP Global SettingsSelect Enable in the Spanning Tree State field Defining STP Global Parameters 117 Defining STP Port Settings 118 Ethernet Fast Ethernet Gigabit Ethernet Displaying the STP Port Table Click Apply Changes. STP is enabled on the portEnabling STP on a Port Modifying STP Port Properties 120 Defining STP LAG Settings 121 122 Configuring Rapid Spanning TreeOpen the STP LAG Settings Modifying the LAG STP Parameters 123 Enabling Rstp Defining Vlan Members Configuring VLANs124 125 Adding New VLANsOpen the Vlan Membership Create New Vlan page opens 126 Vlan Port Membership TableModifying Vlan Membership Groups Deleting Vlan Membership Groups Deleting a Vlan Assigning Ports to a Vlan Group127 128 Defining Vlan Ports SettingsAssigning Port Settings Open the Vlan Port Settings Displaying the Vlan Port Table Defining Vlan LAG Settings129 130 Assigning Vlan LAG SettingsOpen the Vlan LAG Setting Displaying the Vlan LAG Table 131 Aggregating Ports Open the LAG Membership Configuring a Port to a LAGMulticast Forwarding Support Defining LAG Membership Enabling Bridge Multicast Filtering on the Device Defining Multicast Global Parameters133 Enabling Igmp Snooping on the Device Adding Bridge Multicast Address Members134 Define the Vlan ID and New Bridge Multicast Address fields Adding Bridge Multicast AddressesOpen the Bridge Multicast Group Add Bridge Multicast Group page opens 136 Defining Ports to Receive Multicast ServiceAssigning LAGs to Receive Multicast Service Assigning Multicast Forward All Parameters Port Control Definition 137 138 Attaching a Port to a Multicast Router or SwitchAttaching a LAG to a Multicast Router or Switch Open Bridge Multicast Forward All 139 Igmp Snooping 140 Displaying the Igmp Snooping Table Viewing Rmon Statistics Group Viewing Rmon Statistics141 Open the Rmon Statistics Group Viewing ChartsViewing the CPU Utilization Viewing Interface Statistics CPU Utilization 143 CoS Value Forwarding Queue Values VPT Tag Classification Information144 Dscp Value Forwarding Queue Values CoS Services145 Enabling Quality of Service Defining CoS SettingsDefining CoS Global Parameters Selecting Trust Defining QoS Interface Settings147 Displaying the QoS Interface Settings Table Defining Queue SettingsAssigning QoS/CoS settings for an interface Open the Interface Settings Open the QoS Queue Settings Defining the Queue Settings149 Mapping a CoS value to a Queue Mapping CoS Values to QueuesOpen the CoS to Queue Mapping Table 151 Restoring default valuesMapping Dscp Values to Queues Mapping a Dscp value and assigning priority queue Open the Dscp to Queue Check the Restore Defaults checkbox 153 Accessing the Device Through the CLIConsole Connection Telnet Connection 154 Using the CLICommand Mode Overview User Exec Mode Global Configuration Mode Privileged Exec Mode155 Port Channel Mode Interface Configuration ModeInterface Mode Vlan Mode Command copy CLI Commands Debug-mode Command debug-modeCommand do Character Description Command exit configuration Command end 160 Command exit ExecCommand help Command interface ethernet Interface vlan vlan-id Command interface port-channelCommand interface vlan Interface port-channel port-channel-number No ip address Command ip address162 163 Command pingDefaults User Guidelines 164 165 Command show tech-support commandShow tech-support config memory Show clock show system show version 166 Command snmp-server community Default Command username167 168 169 170 171 172 173 174 175 176 177 178 Index Page Page 182 183 184