Setting items | Setting details | |
|
| |
Distance | Feet / Meters : Set the unit of distance. | |
Set distance from listening | Step : Set the minimum variable width of the distance. | |
position to speakers. | • 1ft / 0.1ft | |
Measure beforehand the | • 0.1m / 0.01m | |
distance from the listening |
| |
Default : The “Distance” settings are returned to the default settings. | ||
position to each speaker. | ||
• Yes : Reset to the defaults. | ||
| ||
| • No : Do not reset to the defaults. | |
| When you select “Default” and press ENTER, the “Return all settings | |
| to the default?” prompt is displayed. Select either “Yes” or “No”, and | |
| press ENTER. | |
| Front L / Front R / Center / Subwoofer / Subwoofer 1z1 / Subwoofer | |
| 2z2 / Surr.L / Surr.R / Surr.Back Lz2 / Surr.Back Rz2 / Front Height | |
| L / Front Height R / Front Wide L / Front Wide R : Select the speaker. | |
| zz1 When the “Speaker Config.” – “Subwoofer” setting (vpage 96) is | |
| set to “2 spkrs”, “Subwoofer 1” and “Subwoofer 2” are displayed. | |
| zz2 When the “Speaker Config.” – “Surround Back” setting (vpage 96) | |
| is set to “1 spkr”, “Surround Back” is displayed. | |
| • 0.0ft – 60.0ft / 0.00m – 18.00m : Set the distance. | |
| • The speakers that can be selected differ depending on the “Amp Assign” | |
| (vpage 95) and “Speaker Config.” (vpage 95) settings. | |
| • Default settings : | |
| Front L / Front R / Center / Subwoofer / Subwoofer 1 / Subwoofer 2 / | |
| Front Height L / Front Height R / Front Wide L / Front Wide R : 12.0 ft | |
| (3.6 m) | |
| Surr. L / Surr. R / Surr.Back L / Surr.Back R : 10.0 ft (3.0 m) | |
| • Set the difference in the distance between the speakers to less than 20 | |
| ft (6.0 m). | |
| NOTE | |
| Speakers set to “None” in “Speaker Config.” (vpage 95) are not | |
| displayed. |
| MANUAL SETUP |
|
|
Setting items | Setting details |
|
|
Channel Level | Test Tone : Output test tone. |
Set the volume of the test | • Front L / Front Height L / Center / Front Height R / Front R / Front |
tone to be the same when it Wide R / Surround R / Surr.Back Rz1 / Surr.Back Lz1 / Surround is output from each speaker. L / Front Wide L / Subwoofer / Subwoofer 1z2 / Subwoofer 2z2 / Subwoofer 1+2z2 : Select the speaker.
zz1 When the “Speaker Config.” – “Surround Back” setting (vpage 96) is set to “1 spkr”, “Surr.Back” is displayed.
zz2 When the “Speaker Config.” – “Subwoofer” setting (vpage 96) is set to “2 spkrs”, “Subwoofer 1”, “Subwoofer 2” and “Subwoofer 1+2” are displayed.
•
•After aligning both the distances and levels of subwoofer 1 and subwoofer 2, please adjust subwoofer 1+2. These parameters affects the volume of subwoofer 1+2.
•By clicking o p, the volume of both subwoofer 1 and subwoofer 2 moves down or up together.
•If one of subwoofer1 or subwoofer 2 reaches ±12.0 dB, then the cursors don’t move further.
•When “Channel Level” is adjusted, the adjusted values are set for all the surround modes. To adjust the channel level separately for the different surround modes, use the operation see page 66.
NOTE
•Speakers set to “None” in the “Speaker Config.” (vpage 95) settings are not displayed.
•When a headphones jack is inserted in the PHONES jack of this unit, the “Channel Level” is not displayed.
Default : The “Channel Level” settings are returned to the default settings.
•Yes : Reset to the defaults.
•No : Do not reset to the defaults.
version Simple
version Basic
version Advanced
Information
Remote control operation | Move the cursor | Confirm the setting | Return to previous menu | 97 |
buttons | (Up/Down/Left/Right) |
| ||
|
|
|