Error messages
Simple
An error message is displayed if Audyssey® Auto Setup could not be completed due to speaker placement, the measurement environment, etc. If this happens, check the relevant items, be sure to take the necessary measures, then perform Audyssey Auto Setup over again.
NOTE
Be sure to turn off the power before checking speaker connections.
|
| Examples | Error details | Measures | |
|
|
|
| • Correct measurement is not possible due to | • When using a subwoofer with |
| AUDYSSEY AUTO SETUP |
| |||
|
| inappropriate subwoofer volume. | amplifier (active type), use “SW Level | ||
| Caution! | 1 2 3 4 5 6 |
| ||
|
|
| Matching” to adjust the subwoofer volume | ||
| The subwoofer’s level is too high or low. Please select “SW |
|
| (vpage 11 “Subwoofer level error message | |
| Level Matching” and adjust the level of your subwoofer unit. |
|
| ||
| If you do not want to use the |
|
| and how to adjust”). | |
| subwoofer, select “Skip”. |
|
| ||
|
|
|
|
| • When using a subwoofer without a |
| SW Level Matching |
|
| amplifier, select “Skip”, and then press | |
| Skip |
|
|
| ENTER. |
|
|
|
|
|
|
| AUDYSSEY AUTO SETUP |
| • The connected setup microphone is broken, | • Connect the included setup microphone to | |
|
| or a device other than the supplied setup | the SETUP MIC jack of this unit. | ||
|
|
|
| ||
|
| Caution! |
| ||
|
|
| microphone is connected. |
| |
| No microphone or speaker |
|
| ||
|
| • Not all speakers could be detected. |
| ||
|
|
|
|
| |
|
|
|
| • The front L speaker was not properly | • Check the speaker connections. |
|
| Retry |
| detected. |
|
|
|
|
|
| |
|
|
|
|
|
|
|
| RETURN Cancel |
|
|
|
| AUDYSSEY AUTO SETUP |
| • There is too much noise in the room for | • Either turn off any device generating noise | |
|
| accurate measurements to be made. | or move it away. | ||
|
|
|
| ||
|
| Caution! |
| ||
|
|
|
| • Perform again when the surroundings are | |
| Ambient noise is too high |
|
| ||
|
|
| quieter. | ||
|
| or Level is too low |
|
| |
|
|
|
| • Speaker or subwoofer sound is too low for | • Check the speaker installation and the |
|
| Retry |
| accurate measurements to be made. | direction in which the speakers are facing. |
|
|
|
| • Adjust the subwoofer’s volume. | |
|
|
|
|
| |
|
|
|
|
|
|
|
| RETURN Cancel |
|
|
|
| AUDYSSEY AUTO SETUP |
| • The displayed speaker could not be detected. | • Check the connections of the displayed | |
|
|
| speaker. | ||
|
|
|
|
| |
| Caution! | 1 2 3 4 5 6 |
|
| |
|
|
|
| ||
| Front R | None |
|
|
|
| Retry |
|
|
|
|
|
|
|
|
|
|
|
| RETURN Cancel |
|
|
|
| AUDYSSEY AUTO SETUP |
| • The displayed is connected with the | • Check the polarities of the displayed | |
|
| polarities reversed. | speaker. | ||
|
|
|
| ||
| Caution! | 1 2 3 4 5 6 |
| ||
|
|
| • For some speakers, this error message may | ||
| Front L | Phase |
|
| |
|
|
|
|
| be displayed even if the speaker is properly |
|
|
|
|
| connected. If you are sure the connection is |
|
|
|
|
| correct, press ui to select “Skip”, then |
| Retry |
|
|
| press ENTER. |
| Skip |
|
|
|
|
|
| RETURN Cancel |
|
|
|
The optimal level of each subwoofer channel for Audyssey Auto Setup measurement is 75 dB. During subwoofer level measurement (“Set up speakers (Audyssey® Auto Setup), STEP2 Detection & Measurement ” (vpage 9), 6 – q), an error message is displayed when one level of subwoofers is outside the 72 – 78 dB range. When using a subwoofer with
1 Select “SW Level Matching” and then press ENTER.
AUDYSSEY AUTO SETUP
Caution! | 1 2 3 4 5 6 |
The subwoofer’s level is too high or low. Please select “SW Level Matching” and adjust the level of your subwoofer unit. If you do not want to use the
subwoofer, select “Skip”.
SW Level Matching
Skip
| Enter | RETURN | Cancel |
|
| Proceed to subwoofer volume adjustment item |
|
| |
|
|
|
|
|
version
version Basic
version Advanced
Information
Remote control operation | Move the cursor | Confirm the setting | Return to previous menu | 11 | |
buttons | (Up/Down/Left/Right) | ||||
|
|
|