Setting items | Setting details |
|
|
Height Gain | Low : Reduce the front height channel volume. |
Control the front | height Mid : Front height channel sound is output with standard sound volume. |
channel volume. | High : Increase the front height channel volume. |
| NOTE |
| “Height Gain” is displayed for the following settings. |
| • When the “Speaker Config.” – “Front Height” setting (vpage 96) is set |
| other than to “None”. |
| • When surround mode is “PLgz” or the PLgz decoder is used. |
PLgz Height | ON : Audio is output from the front height speaker. |
Determine whether to use | OFF : Audio is not output from the front height speaker. |
front height channel. | NOTE |
| |
| • “PLgz Height” is displayed with the settings listed below. |
| • When the “Speaker Config.” – “Front Height” setting (vpage 96) is |
| set to other than “None”. |
| • “PLgz Height” cannot be set if the HD Audio source being played |
| includes a front height channel. In this case, the Front height channel |
| is played back without decoding in PLgz mode, using the input signal. |
Speaker | Height/Wide : Sound is output from the front height speakers and front |
Make settings for the | wide speakers. |
speakers outputting sound | Height : Sound is output from the front height speakers. |
when playing back in | Wide : Sound is output from the front wide speakers. |
DENON original surround | OFF : Sound is not output from the front wide speakers and front height |
mode. | speakers. |
| NOTE |
| Only speakers that are set to something other than “None” in “Speaker |
| Config.” (vpage 95) can be selected. |
Subwoofer Att. | ON : Set. |
Attenuate subwoofer level | OFF : Do not set. Usually use in this mode. |
when using EXT. IN input. | Set this to “ON” if the subwoofer channel level seems too high when |
| |
| playing audio signal. |
Subwoofer | ON : The subwoofer is used. |
Turn subwoofer output on | OFF : The subwoofer is not used. |
and off. | NOTE |
| |
| This can be set when the surround mode is “DIRECT” (vpage 52) and the |
| “Subwoofer Mode” (vpage 96) is “LFE+Main”. |
Effect | ON : Create a wider sound stage. |
Switch effect signal for | OFF : The effect is not set. |
| |
and off. |
|
AUDIO/VIDEO ADJUST
Setting items | Setting details |
|
|
Effect Level | 1 – 15 (10) |
Adjust effect signal level. | Set to a lower level if the positioning and sense of phase of the |
| |
| surround signals seems unnatural. |
Room Size | Medium : Simulate acoustics of a medium room. |
Determine size of acoustic | |
environment. | Large : Simulate acoustics of a large room. |
| Small : Simulate acoustics of a small room. |
| |
| NOTE |
| “Room Size” does not indicate the size of the room in which sources are |
| played. |
Default | Yes : Reset to the defaults. |
The “Surround Parameters” No : Do not reset to the defaults. settings are returned to the
default settings.
nnToneAdjust the tonal quality of the sound.
Setting items | Setting details |
|
|
Tone Control | ON : Allow tone adjustment (bass, treble). |
Set the tone control function OFF : Playback without tone adjustment. | |
to ON and OFF. | “Tone Control” can be set when “Dynamic EQ” (vpage 89) and |
| |
| “Dolby Volume” (vpage 91) are set to “OFF”. |
NOTE
•“Tone Control” settings are not reflected to ZONE2 and ZONE3.
•The tone cannot be adjusted in the direct mode.
Bass | ||
Adjust low frequency range | “Bass” can be set when “Tone Control” is set to “ON”. | |
(bass). | ||
| ||
Treble | ||
Adjust high frequency range |
|
(treble). | “Treble” can be set when “Tone Control” is set to “ON”. |
|
88 | Remote control operation | Move the cursor | Confirm the setting | Return to previous menu |
| buttons | (Up/Down/Left/Right) | ||
|
|
|