ÊTower Wiring Installation | Eaton Electrical 9130 specs

INSTALLATION

ÊTower Wiring Installation

This section explains:

SInstalling the UPS, including connecting the UPS internal batteries

SConnecting any optional EBMs

Installing the UPS

NOTE Do not make unauthorized changes to the UPS; otherwise, damage may occur to your equipment and void your warranty.

NOTE Do not connect the UPS power cord to utility until after installation is completed.

To install the UPS:

1.Remove the UPS front cover (see Figure 14).

To remove the cover, push down on the top of the cover and pull the cover toward you to unclip it from the cabinet.

NOTE A ribbon cable connects the LCD control panel to the UPS. Do not pull on the cable or disconnect it.

NOTE Leave ribbon cable connected.

Figure 14. Removing the UPS Front Cover

30	Eaton® 9130 UPS (700–3000 VA) User's Guide S 164201718 Rev 2 www.powerware.com

Image 38

Eaton Electrical 9130 manual ÊTower Wiring Installation, Removing the UPS Front Cover

Contents

Eaton 9130 UPS 700-3000 VA Users Guide Class a EMC Statements Low Voltage Models over 1500 VA FCC Part ICES-003 Class B EMC Statements Special Symbols Requesting a Declaration of Conformity Table of Contents Troubleshooting UPS MaintenanceSpecifications 101 Warranty 107 Table of Contents Chapter Introduction Shows the Eaton 9130 tower UPS and optional EBM N G E R R N I N G R E U T I O NSikkerhedsanvisninger V a a R V a R S E LBelangrijke Veiligheidsinstructies A R S C H U W I N G A R a G E L E TTarkeita Turvaohjeita R O I T U S R O Consignes de sécurité Sicherheitswarnungen R N U N G H T U N G Avvisi di sicurezza T E N Z I O N E R I C O L OV E R T E N Z a R S I K T I G Viktig SikkerhetsinformasionR L I G V E R T Ê N C I a Regulamentos de SegurançaI D a D O R I G O Ïàñíî Ïðåäóïðåæäåíèå L I G R O ÎñòîðîæíîAdvertencias de Seguridad V E R T E N C I a R a E C a U C I Ó NSäkerhetsföreskrifter K T I G T Chapter Installation ÊInspecting the Equipment ÊChecking the Accessory Kit ÊUnpacking the Cabinet Tools Required ÊRackmount InstallationChecking the Rail Kit Accessories Rackmount Setup Assembling the Rails Securing the Rails Installing the Mounting Brackets Forward Position Shown ÊRackmount Wiring Installation Installing the UPS Removing the UPS Right Front Cover Connecting the UPS Internal Batteries Connecting the EBMs Removing the EBM Cable Knockout Removing the EBM Front Cover Typical EBM Installation ÊTower Installation ÊTower Wiring Installation Removing the UPS Front Cover Connecting the UPS Internal Batteries Connecting the EBMs Connecting the EBMs Êups Initial Startup To start up the UPS Installation Installation ÊControl Panel Functions Eaton 9130 Control Panel Changing the Language Indicator DescriptionsIndicator Status Description Display Functions Menu Map for Display Functions Main Menu Submenu Display Information or Menu Function User Settings User Settings Description Available Settings Default Setting Frequency Converter Enabled Disabled When in Spec ÊOperating Modes Normal ModeBattery Mode Bypass Mode Starting the UPS Standby ModeÊups Startup and Shutdown Starting the UPS on Battery UPS Shutdown ÊTransferring the UPS Between ModesÊRetrieving the Event Log ÊSetting Power Strategy ÊConfiguring Bypass Settings ÊConfiguring Load Segments Operation All UPS and EBM Cabinets ÊConfiguring Battery SettingsConfiguring the UPS for EBMs Running Automatic Battery Tests Configuring Automatic Restart Communication RS-232 and USB Communication Ports ÊInstalling Communication Options and Control TerminalsÊCommunication Options Independent Multiplexed Communication Bay Pin Number Signal Name Function Direction from the UPS GND Remote Emergency Power-off Connectivity Cards Repo Connections Relay Output Contacts Relay Output Configuration OptionsSignal Description Polarity Options Programmable Signal InputsProgrammable Signal Inputs Input Description ÊPowerware LanSafe Power Management Software ÊModem Operation UPS Maintenance Êups and Battery Care ÊReplacing Batteries ÊWhen to Replace BatteriesÊStoring the UPS and Batteries Replacing Rackmount UPS Internal Batteries Disconnecting the UPS Internal Batteries Shown without EBMs U T I O N Replacing Tower UPS Internal Batteries Replacing the UPS Internal Batteries U T I O N Replacing Rackmount EBMs UPS Maintenance Replacing Tower EBMs ÊTesting New Batteries ÊRecycling the Used Battery or UPS ÊUpdating the UPS Firmware UPS Maintenance Communication Options All Models ÊModel SpecificationsExtended Battery Module Model List Model Power Level Rear Panel Diagram UPS Model List Rackmount Models UPS Model List Tower Models Model Rackmount EBM Weights and Dimensions Rackmount ModelsModel Rackmount UPS Dimensions H W D Weight Weights and Dimensions Tower Models Electrical Input All Models Model Default Input Selectable Input Voltage Range Electrical Input Rackmount Models Electrical Input Tower Models Electrical Input Connections Rackmount Models Model Input Connection Input Cable Electrical Input Connections Tower Models Electrical Output All Models Electrical Output Connections Rackmount Models Model Output Connections Output Cables Electrical Output Connections Tower Models Environmental and Safety All Models Battery Runtimes in Minutes at 100% Load Rack Models Model Internal Batteries + 1 EBM + 2 EBMs + 3 EBMs + 4 EBMs Battery Runtimes in Minutes at 100% Load Tower Models Battery Internal Batteries EBMs ÊRear Panels Models PW9130L700R-XL2U, PW9130L1000R-XL2U Model PW9130G1000R-XL2UAU Model PW9130L2000R-XL2U Models PW9130L2500R-XL2U, PW9130L3000R-XL2U Model PW9130L1500T-XL Model PW9130G2000T-XL Model PW9130i1500T-XL Model PW9130G1000T-XLAU Model PW9130G2000T-XLAU 100 Troubleshooting ÊTypical Alarms and Conditions Alarm or Condition Possible Cause Action Battery is running low Models Only. Ground wire LED is on Beep every second UPS does not start ÊSilencing the Alarm ÊService and Support 106 Chapter Warranty ÊTwo-Year Limited Warranty US and Canada Warranty ÊTen-Year Pro-Rated Limited Warranty US and Canada 110 ÊLoad Protection Guarantee US and Canada 112