Eaton Electrical 9130

UPS MAINTENANCE

Eaton® 9130 UPS (700–3000 VA) User's Guide S 164201718 Rev 2 www.powerware.com 67

2. Remove and retain the two screws holding the internal battery

connector. Disconnect the internal battery connector. See

Figure 26.

Battery Cover Plate

Internal

Battery

Connector

Battery Tray Handle

Figure 26. Replacing the UPS Internal Batteries

3. Remove and retain the two screws holding the battery cover plate.

Grasp an edge of the battery cover plate and pull it forward gently.

Remove and retain the battery cover plate.

4. Carefully pull the handle on the battery tray and slide the battery

package slowly out onto a flat, stable surface; use two hands to

support the battery package. See “Recycling the Used Battery or

UPS” on page 73 for proper disposal.

NOTE Verify that the replacement batteries have the same rating as the batteries being

replaced.

5. Slide the new battery package into the cabinet. Push the battery

package in firmly.

Contents

Main Class A EMC Statements (Low Voltage Models over 1500 VA) FCC Part 15 ICES-003 EN 62040-2 VCCI Notice Class B EMC Statements (Low Voltage Models up to 1500 VA and High Voltage Models up to 3000 VA) FCC Part 15 VCCI Notice ICES-003 Requesting a Declaration of Conformity Special Symbols CAUTION: REFER TO OPERATOR'S MANUAL Table of Contents Page Page Page Chapter 1 Introduction Page Chapter 2 Safety Warnings IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS D A N G E S S S VIGTIGE SIKKERHEDSANVISNINGER GEM DISSE ANVISNINGER F A R A D V A R S E L S S S BELANGRIJKE VEILIGHEIDSINSTRUCTIES BEWAAR DEZE INSTRUCTIES G E V A A W A A R S C H U W I N G S O P G E L E TRKEIT TURVAOHJEITA - SUOMI SILYT NM OHJEET V A A R V A R O I T U S S S S CONSIGNES DE SCURIT IMPORTANTES CONSERVER CES INSTRUCTIONS D A N G E R A V E R T I S S E M E N T S A T T E N T I O N WICHTIGE SICHERHEITSANWEISUNGEN AUFBEWAREN W A R N U N G A C H T U N S V O R S I C H T ! IMPORTANTI ISTRUZIONI DI SICUREZZA CONSERVARE QUESTE ISTRUZIONI P E R I C O L O A V V E R T E N Z S A T T E N Z I O N S VIKTIGE SIKKERHETSINSTRUKSJONER GJEM DISSE INSTRUKSJONENE S F A R L I S S S INSTRUES DE SEGURANA IMPORTANTES GUARDE ESTAS INSTRUES S C U I D A D O A D V E R T N C I S S INSTRUCCIONES DE SEGURIDAD IMPORTANTES GUARDE ESTAS INSTRUCCIONES P E L I G R A D V E R T E N C I S P R E C A U C I N VIKTIGA SKERHETSFRESKRIFTER SPARA DESSA FRESKRIFTER F A R V A R N I N G S V I K T I G T Chapter 3 Installation Inspecting the Equipment Unpacking the Cabinet S Checking the Accessory Kit S S S S S S Rackmount Installation Checking the Rail Kit Accessories S Tools Required S S S Rackmount Setup S Page Page Rackmount Wiring Installation S S Installing the UPS Page Page Connecting the EBM(s) Page Page Tower Installation Tower Wiring Installation S S Installing the UPS Page Connecting the EBM(s) Page UPS Initial Startup Page Page Chapter 4 Operation Control Panel Functions esc Changing the Language Display Functions Table 2 shows the basic menu structure. Table 2. Menu Map for Display Functions User Settings The following table displays the options that can be changed by the user. Page Page Operating Modes Normal Mode Battery Mode Bypass Mode S S S S Standby Mode UPS Startup and Shutdown S S S Starting the UPS Starting the UPS on Battery UPS Shutdown Transferring the UPS Between Modes Retrieving the Event Log Setting Power Strategy Configuring Bypass Settings S S S Configuring Load Segments S S Page Configuring Battery Settings Configuring the UPS for EBMs Running Automatic Battery Tests S S S S S Configuring Automatic Restart Chapter 5 Communication Installing Communication Options and Control Terminals Communication Options RS-232 and USB Communication Ports Page Connectivity Cards S Remote Emergency Power-off S You can set the REPO polarity. See the REPO Input Polarity setting in User Settings on page 40. Relay Output Contacts Programmable Signal Inputs Modem Operation Powerware LanSafe Power Management Software Chapter 6 UPS Maintenance UPS and Battery Care Storing the UPS and Batteries When to Replace Batteries S Replacing Batteries S Replacing Rackmount UPS Internal Batteries Page Page Replacing Tower UPS Internal Batteries Page Page Replacing Rackmount EBMs Page Replacing Tower EBMs Testing New Batteries Recycling the Used Battery or UPS S Updating the UPS Firmware Page Chapter 7 Specifications Model Specifications This section provides the following specifications: S S S S S S Table 8. Communication Options (All Models) Table 10. UPS Model List (Rackmount Models) Table 11. UPS Model List (Tower Models) Page Page Table 15. Electrical Input (Rackmount Models) Table 16. Electrical Input (Tower Models) Table 17. Electrical Input Connections (Rackmount Models) Table 18. Electrical Input Connections (Tower Models) Table 19. Electrical Output (All Models) Table 20. Electrical Output Connections (Rackmount Models) Table 21. Electrical Output Connections (Tower Models) Table 22. Environmental and Safety (All Models) Table 23. Battery Runtimes (in Minutes) at 100% Load (Rack Models) Table 24. Battery Runtimes (in Minutes) at 100% Load (Tower Models) Table 25. Battery Rear Panels Page Page Page Page Page Page Page Page Page Chapter 8 Troubleshooting S Typical Alarms and Conditions Page Page Page Silencing the Alarm Service and Support Page Chapter 9 Warranty Two-Year Limited Warranty (US and Canada) Powerware UPS Models: 3105, 9120, 9125, 9130, 9140, and FERRUPS up to 3.1 kVA WARRANTOR: LIMITED WARRANTY: Page COSTS NOT RELATED TO WARRANTY: OBTAINING WARRANTY SERVICE: Ten-Year Pro-Rated Limited Warranty (US and Canada) Powerware UPS Models: 5115, 5125, 5140, 9120, 9125, 9130, 9140, 9155, 9170+, and FERRUPS WARRANTOR: LIMITED WARRANTY: WHAT THIS WARRANTY COVERS: Page Load Protection Guarantee (US and Canada) Powerware UPS Models 3105, 5110, 5115, 5125, 9120, 9125, 9130, 9140, 9150, 9155, 9170+, and FERRUPS