ÊRackmount Wiring Installation | Eaton Electrical 9130 instruction

INSTALLATION

13.Optional. Insert a rear stop bracket through the inside of each rail behind the UPS. Rotate each bracket and slide the bracket until it fits tightly against the UPS's rear panel. Secure each bracket to the UPS with one M3 8 pan-head screw. See Figure 8.

Repeat for any optional cabinets.

14.Continue to the following section, “Rackmount Wiring Installation.”

Rear Stop Bracket

M3 8 Pan-Head Screw

Figure 8. Securing the Back of the Cabinet (Optional)

ÊRackmount Wiring Installation

This section explains:

SInstalling the UPS, including connecting the UPS internal batteries

SConnecting any optional EBMs

Installing the UPS

NOTE Do not make unauthorized changes to the UPS; otherwise, damage may occur to your equipment and void your warranty.

NOTE Do not connect the UPS power cord to utility until after installation is completed.

To install the UPS:

1.Remove the UPS right front cover (behind the LCD control panel). See Figure 9.

To remove the cover, remove and retain the two screws on the right side of the cover. Grasp the top and bottom of the cover and slide the cover to the right.

Eaton® 9130 UPS (700–3000 VA) User's Guide S 164201718 Rev 2 www.powerware.com

23

Image 31

Eaton Electrical 9130 manual ÊRackmount Wiring Installation, Installing the UPS

Contents

Eaton 9130 UPS 700-3000 VA Users Guide FCC Part ICES-003 Class a EMC Statements Low Voltage Models over 1500 VA Class B EMC Statements Requesting a Declaration of Conformity Special Symbols Table of Contents 101 UPS MaintenanceSpecifications Troubleshooting 107 Warranty Table of Contents Chapter Introduction Shows the Eaton 9130 tower UPS and optional EBM R N I N G N G E R Sikkerhedsanvisninger U T I O NR E A R S C H U W I N G V a R S E LBelangrijke Veiligheidsinstructies V a a R R O I T U S G E L E TTarkeita Turvaohjeita A R a Consignes de sécurité R O R N U N G Sicherheitswarnungen Avvisi di sicurezza H T U N G V E R T E N Z a R I C O L OT E N Z I O N E R L I G Viktig SikkerhetsinformasionR S I K T I G R I G O Regulamentos de SegurançaI D a D O V E R T Ê N C I a Ïðåäóïðåæäåíèå Ïàñíî V E R T E N C I a ÎñòîðîæíîAdvertencias de Seguridad L I G R O Säkerhetsföreskrifter E C a U C I Ó NR a K T I G T ÊInspecting the Equipment Chapter Installation ÊUnpacking the Cabinet ÊChecking the Accessory Kit Checking the Rail Kit Accessories ÊRackmount InstallationTools Required Assembling the Rails Rackmount Setup Securing the Rails Installing the Mounting Brackets Forward Position Shown Installing the UPS ÊRackmount Wiring Installation Removing the UPS Right Front Cover Connecting the UPS Internal Batteries Removing the EBM Cable Knockout Connecting the EBMs Removing the EBM Front Cover Typical EBM Installation ÊTower Installation Removing the UPS Front Cover ÊTower Wiring Installation Connecting the UPS Internal Batteries Connecting the EBMs Connecting the EBMs To start up the UPS Êups Initial Startup Installation Installation Eaton 9130 Control Panel ÊControl Panel Functions Display Functions Indicator DescriptionsIndicator Status Description Changing the Language Main Menu Submenu Display Information or Menu Function Menu Map for Display Functions User Settings Description Available Settings Default Setting User Settings Frequency Converter Enabled Disabled When in Spec Battery Mode Normal ModeÊOperating Modes Bypass Mode Êups Startup and Shutdown Standby ModeStarting the UPS Starting the UPS on Battery ÊRetrieving the Event Log ÊTransferring the UPS Between ModesUPS Shutdown ÊConfiguring Bypass Settings ÊSetting Power Strategy ÊConfiguring Load Segments Operation Configuring the UPS for EBMs ÊConfiguring Battery SettingsAll UPS and EBM Cabinets Configuring Automatic Restart Running Automatic Battery Tests Communication Independent Multiplexed Communication Bay ÊInstalling Communication Options and Control TerminalsÊCommunication Options RS-232 and USB Communication Ports GND Pin Number Signal Name Function Direction from the UPS Connectivity Cards Remote Emergency Power-off Repo Connections Signal Description Relay Output Configuration OptionsRelay Output Contacts Input Description Programmable Signal InputsProgrammable Signal Inputs Polarity Options ÊModem Operation ÊPowerware LanSafe Power Management Software Êups and Battery Care UPS Maintenance ÊStoring the UPS and Batteries ÊWhen to Replace BatteriesÊReplacing Batteries Replacing Rackmount UPS Internal Batteries Disconnecting the UPS Internal Batteries Shown without EBMs U T I O N Replacing Tower UPS Internal Batteries Replacing the UPS Internal Batteries U T I O N Replacing Rackmount EBMs UPS Maintenance Replacing Tower EBMs ÊTesting New Batteries ÊUpdating the UPS Firmware ÊRecycling the Used Battery or UPS UPS Maintenance Extended Battery Module Model List ÊModel SpecificationsCommunication Options All Models UPS Model List Rackmount Models Model Power Level Rear Panel Diagram UPS Model List Tower Models Model Rackmount UPS Dimensions H W D Weight Weights and Dimensions Rackmount ModelsModel Rackmount EBM Electrical Input All Models Weights and Dimensions Tower Models Electrical Input Rackmount Models Model Default Input Selectable Input Voltage Range Electrical Input Tower Models Model Input Connection Input Cable Electrical Input Connections Rackmount Models Electrical Input Connections Tower Models Electrical Output All Models Model Output Connections Output Cables Electrical Output Connections Rackmount Models Electrical Output Connections Tower Models Environmental and Safety All Models Model Internal Batteries + 1 EBM + 2 EBMs + 3 EBMs + 4 EBMs Battery Runtimes in Minutes at 100% Load Rack Models Battery Runtimes in Minutes at 100% Load Tower Models Internal Batteries EBMs Battery Models PW9130L700R-XL2U, PW9130L1000R-XL2U ÊRear Panels Model PW9130G1000R-XL2UAU Model PW9130L2000R-XL2U Models PW9130L2500R-XL2U, PW9130L3000R-XL2U Model PW9130L1500T-XL Model PW9130G2000T-XL Model PW9130i1500T-XL Model PW9130G1000T-XLAU Model PW9130G2000T-XLAU 100 ÊTypical Alarms and Conditions Troubleshooting Battery is running low Alarm or Condition Possible Cause Action LED is on Beep every second Models Only. Ground wire UPS does not start ÊService and Support ÊSilencing the Alarm 106 ÊTwo-Year Limited Warranty US and Canada Chapter Warranty Warranty ÊTen-Year Pro-Rated Limited Warranty US and Canada 110 ÊLoad Protection Guarantee US and Canada 112