Options | Emerson 00809-0100-4102 guide

Reference Manual	Appendix A: Reference Data
00809-0100-4102, Rev AA	May 2013

A.7 Options

Standard configuration

Unless otherwise specified, transmitter is shipped as follows:

Engineering units
Differential/Gage:	inH2O (Range 0, 1, 2, and 3)
	psi (Range 4 and 5)
Absolute/2051TA:	psi (all ranges)
Low Limit:	0 (engineering units above)
High Limit:	Upper range limit
Output:	Linear
Flange type:	Specified model code option
Flange material:	Specified model code option
O-ring material:	Specified model code option
Drain/vent:	Specified model code option
LCD Display:	Installed or none
Software tag:	(Blank)

Custom configuration

If Option Code C1 is ordered, the customer may have the factory pre-configure special parameters in the transmitter.

Refer to the “Rosemount 2051 Wireless Configuration Data Sheet” document number 00806-0100-4102.

Tagging (3 options available)







Standard SST hardware tag is wired to the transmitter. Tag character height is 0.125 in. (3,18 mm), 56 characters maximum.

Tag may be permanently stamped on transmitter nameplate upon request, 56 characters maximum.

Tag may be stored in transmitter memory. Character limit is dependent on protocol.

–-WirelessHART: 32 characters

Optional Rosemount 304, 305, or 306 Integral Manifolds

Factory assembled to 2051C and 2051T transmitters. Refer to the following Product Data Sheet (document number 00813-0100-4839 for Rosemount 304 and 00813-0100-4733 for Rosemount 305 and 306) for additional information.

Other seals

Refer to Product Data Sheet 00813-0100-4016 for additional information.

Specifications and Reference Data

127

Image 139

Emerson 00809-0100-4102 manual Options

Contents

Rosemount 2051 Wireless Pressure Transmitters Page Reference Manual Rosemount 2051 Wireless Pressure, Flow, and Level Solutions Explosions could result in death or serious injury Iii Reference Manual Contents Table of Contents Reference Manual Installation Troubleshooting Operation and maintenanceCommissioning Appendix B Product Certifications Appendix a Specifications Reference Data Appendix D Network design best practices Appendix C Field Communicator Menu Trees and Fast Keys Table of Contents Reference Manual Rosemount 2051T in-line Pressure Transmitter Using this manualModels covered Rosemount 2051C Coplanar Pressure Transmitter Rosemount 2051CF Flowmeters Rosemount 2051L Level TransmitterIntroduction Reference Manual WirelessHART installation flowchart WirelessHART installation flowchart LCD Display Transmitter overview Antenna position Considerations before transmitter installationWireless considerations Power up sequence Electrical Mechanical Temperature effects Service supportEnvironmental Product Recycling/Disposal Overview Safety messages AMS Wireless Configurator Required bench top configurationConfiguration Reference Manual Bench hook-up Basic setupConnection diagrams Set device tag Join device to network Configure update rateSelect 1 Guided Setup Select 3 Join Device to Network Select 1 Guided Setup Select 4 Configure Update Rate Set process variable units Configure for PressureRemove Power Module Select 2 Manual Setup Select 2 Pressure Variable Mapping Re-mapping using a Field CommunicatorRe-mapping using AMS Device Manager Set range points Setting transmitter output with AMS Device Manager Setting transmitter output with a Field CommunicatorSet transmitter percent of range transfer function Configuring Scaled Variable using AMS Device Manager Configure for Level and FlowConfiguring scaled variable Configuring Scaled Variable using a Field Communicator DP Level Example Scaled Variable Configuration for Tank ApplicationDP Flow example Scaled Variable Configuration for Flow Application Set range points Review device information Review configuration dataSelect 2 Manual Setup Select 9 Device Information Review pressure information Select 2 Variables Review radio informationReview operating parameters Select 7 Device Information Click Manual Setup, select the Display tab Configuring the LCD displayConfiguring LCD display with a Field Communicator Configuring LCD display with AMS Device Manager Damping Detailed transmitter setupConfigure process alerts Select 1 Guided Setup Write protect Diagnostics and service Join status Device reset Number of available neighbors Advanced Functions for Hart Protocol Saving, Recalling, and Cloning Configuration DataField Communicator AMS creating a Reusable Copy AMS Applying a User Configuration Section Installation Installation Reference Manual Reference Manual Installation Installation considerationsConsiderations Internal antenna position Steam serviceMechanical considerations Environmental considerations Draft range considerations Installation Flowchart Output damping Reducing process noiseReference side filtering Circuit side of electronics housing Installation proceduresConsider housing rotation Power Module side of electronics housing Mounting brackets Environmental seal for housingMount the transmitter Mounting brackets Mounting bracket option code B4 Flange bolts Bolt Material Initial Torque Value Final Torque Value Bolt Installation Torque Values Description Qty Size Panel mounting bracket option codes B2 and B8 Best practices Impulse piping Liquid Flow Measurement Mounting Requirements Drain/vent valves Process connectionsCoplanar or traditional process connection Flange adapters Inline gage transmitter orientation Inline process connection 13. Power Module Power Module installation Installing the LCD display 14. Optional LCD Display Rosemount 304, 305 and 306 integral manifolds 15. Integral Manifold Designs Rosemount 305 Integral Manifold installation procedure 16. Bolt tightening pattern Rosemount 306 Integral Manifold installation procedure Manifold operation Rosemount 304 Conventional Manifold installation procedure Pressure downstream side Transmitter first Configuration for zeroingTransmitter to service To zero the 2051, close Block valve to the low Test Close the equalize valve on High pressure upstream Side Open the equalize valve on Low pressure Downstream sideTransmitter. The manifold is Now in the proper Installation Section Commissioning Reference Manual Verifying operation Viewing network statusLocal Display Function Key Sequence Menu Items Smart Wireless Gateway Device Manager Smart Wireless Gateway Explorer Smart Wireless Gateway Network Settings Using the Field Communicator Reference Manual Commissioning Configuring transmitter securityRosemount 2051 Wireless Fast Key Sequence Hart lock Configuring Hart Lock using AMS Device Manager Configuring Hart Lock using Field CommunicatorConfiguration Button lock Calibration overview Operation and maintenance Transmitter Bench Calibration Tasks Field Calibration Tasks Operation and Maintenance Reference ManualDetermining necessary Sensor Trims Recommended Calibration Tasks Determining calibration frequency Trimming with configuration buttons Calculate calibration frequency HT = URV S/100 x P/1000 x LRV Trim the pressure signalSensor Trim Overview Example Sensor Trim example Sensor Trim Performing a Digital Zero Trim option DZ Select 5 Maintenance Select 1 Pressure CalibrationPerforming a Sensor Trim with a Field Communicator Performing a Sensor Trim with AMS Device Manager Line Pressure Effect Range 2 and Range Recall Factory Trim-Sensor TrimCompensating for Line Pressure Range 4 and Range Zero Effect LT = 500 + 0.01/10005001200 506 inH2O 1.26 bar Startup Screen Sequence LCD Screen Messages S R 13 0 Diagnostic Button Screen Sequence T w k K n w n Network Diagnostic Status Screens C H N G Operation and maintenance I l u r Device Diagnostic Screens C d e D i o I l u r N f g R n Troubleshooting Rosemount 2051 Wireless Device Status Information Troubleshooting Reference ManualDevice Status Description Recommended Action Check process for possible saturation condition Reference Manual Troubleshooting Check the buttons for obstructions Symptom Recommended Actions Rosemount 2051 Wireless TroubleshootingWireless Network Troubleshooting Removing from service Conformance to specification ±3σ Sigma Performance SpecificationsDigital output Models Standard Reference Accuracy1Total Performance Appendix a Reference Data Reference Manual Dynamic Performance Long Term StabilityLine Pressure Effect per 1000 psi 6,9 MPa1 Vibration Effect ServiceAmbient Temperature Effect per 50F 28C Mounting Position Effects Range and Sensor Limits Wireless Self-Organizing Networks Overpressure limits Static pressure limit Temperature limitsBurst pressure limits 2051C Coplanar Volumetric DisplacementProcess Temperature Limits Humidity Limits Electrical connections Physical specificationsProcess-Wetted parts Non-Wetted Parts Rosemount 2051L Process Wetted Parts Sensor Module Fill Fluid Table A-4. Transmitter option weights Shipping Weights for 2051 Wireless Pressure TransmitterTable A-2. Transmitter weights without options Table A-3 L weights without options Dimensional Drawings Diameter Gasket Class Size Table A-5 L Dimensional SpecificationsPipe Process Lower Housing G Class Size Side F NPT Outside Extension Pipe Ordering Information Manifold Assembly59 Housing Material Conduit Entry SizeWireless Transmit Rate, Operating Frequency and Protocol Antenna and SmartPower Product Certifications Seal Assemblies9All-Welded Seal Assemblies for high vacuum applications9 Mounting Bracket Cleaning Process Area Hardware AdjustmentsSoftware Configuration Pressure Testing Toolkit Total System Performance Reports RC1/4 RC1/2 Process ConnectionMax Static Line Pressure Surface Finish Options Process Area8 Zero/Span AdjustmentWireless Sensor Module Calibration Certification Typical Model Number 2051T G 5 X 2A 2 1 P WA3 WP5 B4 M5 Code Process Connection Size Material Extension Length ModelMounting Flange Size, Rating, Material High Side Low Pressure Side Flange Configuration Adapter Calibration Certification Standard Bolting Material StandardMaterial Traceability Certification Standard Ring Material Number Size NPT Standard Hardware Adjustments StandardSoftware Configuration Standard Toolkit Total System Performance Reports Standard Line Size Model Product DescriptionPipe I.D. Range Sensor Material Pipe Material / Mounting Assembly MaterialPiping Orientation Annubar Type Isolation Valve for Flo-Tap Models Temperature MeasurementTransmitter Housing Material Conduit Entry Size Opposite Side Support or Packing Gland QC1 Fluid and O-ring Options Standard Material Type Primary Element TechnologyPrimary Element Type Transmitter Housing Material ANSI/ASME B31.1 ANSI/ASME B31.3 ANSI/ASME B31.8 Bore Size Option Body MaterialProcess Connection Orifice Plate Material Differential Pressure Ranges Options LCD Display Hardware Adjustments Standard Options Bolts for flanges and adapters Configuration buttonsOutput information Display and interface options Rosemount 2051C Traditional Flange bracket options Spare parts Telecommunication compliance Wireless CertificationsApproved manufacturing locations European directive information European certifications Ordinary location certification for FMNorth American certifications CSA Canadian Standards Association 注意！ 134 Field Communicator menu trees Appendix C Field Communicator Menu Trees and Fast Keys Appendix C Field Communicator Menu Trees Reference Manual Guided Setup 137 138 Effective range Appendix D Network design best practices Appendix D Network design best practices Appendix D Network design best practices Reference ManualPage Latin America