Bolt tightening pattern | Emerson 00809-0100-4102 instruction

Reference Manual		Section 3: Installation
00809-0100-4102, Rev AA		May 2013

Figure 3-16. Bolt tightening pattern

3.If the PTFE sensor module O-rings have been replaced, the flange bolts should be re-tightened after installation to compensate for cold flow of the O-rings.

4.If applicable, install flange adapters on the process end of the manifold using the 1.75-in. flange bolts supplied with the transmitter.

Note

Always perform a zero trim on the transmitter/manifold assembly after installation to eliminate mounting effects. See Section 5: Operation and maintenance, “Sensor Trim” on page 68.

3.5.2Rosemount 306 Integral Manifold installation procedure

The 306 Manifold is for use only with a 2051T Wireless In-line transmitter.

Assemble the 306 Manifold to the 2051T Wireless In-line transmitter with a thread sealant.

1.Place transmitter into holding fixture.

2.Apply appropriate thread paste or tape to threaded instrument end of the manifold.

3.Count total threads on the manifold before starting assembly.

4.Start turning the manifold by hand into the process connection on the transmitter.

Installation

49

Image 61

Emerson 00809-0100-4102 manual Rosemount 306 Integral Manifold installation procedure, Bolt tightening pattern

Contents

Rosemount 2051 Wireless Pressure Transmitters Page Reference Manual Rosemount 2051 Wireless Pressure, Flow, and Level Solutions Explosions could result in death or serious injury Iii Reference Manual Contents Table of Contents Reference Manual Installation Troubleshooting Operation and maintenanceCommissioning Appendix B Product Certifications Appendix a Specifications Reference Data Appendix D Network design best practices Appendix C Field Communicator Menu Trees and Fast Keys Table of Contents Reference Manual Models covered Using this manualRosemount 2051C Coplanar Pressure Transmitter Rosemount 2051T in-line Pressure Transmitter Rosemount 2051CF Flowmeters Rosemount 2051L Level TransmitterIntroduction Reference Manual WirelessHART installation flowchart WirelessHART installation flowchart LCD Display Transmitter overview Wireless considerations Considerations before transmitter installationPower up sequence Antenna position Electrical Mechanical Temperature effects Service supportEnvironmental Product Recycling/Disposal Overview Safety messages AMS Wireless Configurator Required bench top configurationConfiguration Reference Manual Connection diagrams Basic setupSet device tag Bench hook-up Select 1 Guided Setup Select 3 Join Device to Network Configure update rateSelect 1 Guided Setup Select 4 Configure Update Rate Join device to network Remove Power Module Configure for PressureSelect 2 Manual Setup Select 2 Pressure Set process variable units Re-mapping using AMS Device Manager Re-mapping using a Field CommunicatorSet range points Variable Mapping Setting transmitter output with AMS Device Manager Setting transmitter output with a Field CommunicatorSet transmitter percent of range transfer function Configuring scaled variable Configure for Level and FlowConfiguring Scaled Variable using a Field Communicator Configuring Scaled Variable using AMS Device Manager DP Level Example Scaled Variable Configuration for Tank ApplicationDP Flow example Scaled Variable Configuration for Flow Application Set range points Select 2 Manual Setup Select 9 Device Information Review configuration dataReview pressure information Review device information Review operating parameters Review radio informationSelect 7 Device Information Select 2 Variables Configuring LCD display with a Field Communicator Configuring the LCD displayConfiguring LCD display with AMS Device Manager Click Manual Setup, select the Display tab Configure process alerts Detailed transmitter setupSelect 1 Guided Setup Damping Write protect Diagnostics and service Join status Device reset Number of available neighbors Advanced Functions for Hart Protocol Saving, Recalling, and Cloning Configuration DataField Communicator AMS creating a Reusable Copy AMS Applying a User Configuration Section Installation Installation Reference Manual Reference Manual Installation Installation considerationsConsiderations Mechanical considerations Steam serviceEnvironmental considerations Internal antenna position Draft range considerations Installation Flowchart Output damping Reducing process noiseReference side filtering Consider housing rotation Installation proceduresPower Module side of electronics housing Circuit side of electronics housing Mount the transmitter Environmental seal for housingMounting brackets Mounting brackets Mounting bracket option code B4 Flange bolts Bolt Material Initial Torque Value Final Torque Value Bolt Installation Torque Values Description Qty Size Panel mounting bracket option codes B2 and B8 Best practices Impulse piping Liquid Flow Measurement Mounting Requirements Coplanar or traditional process connection Process connectionsFlange adapters Drain/vent valves Inline gage transmitter orientation Inline process connection 13. Power Module Power Module installation Installing the LCD display 14. Optional LCD Display Rosemount 304, 305 and 306 integral manifolds 15. Integral Manifold Designs Rosemount 305 Integral Manifold installation procedure 16. Bolt tightening pattern Rosemount 306 Integral Manifold installation procedure Manifold operation Rosemount 304 Conventional Manifold installation procedure Transmitter to service Configuration for zeroingTo zero the 2051, close Block valve to the low Pressure downstream side Transmitter first Test Transmitter. The manifold is Open the equalize valve on Low pressure Downstream sideNow in the proper Close the equalize valve on High pressure upstream Side Installation Section Commissioning Reference Manual Verifying operation Viewing network statusLocal Display Function Key Sequence Menu Items Smart Wireless Gateway Device Manager Smart Wireless Gateway Explorer Smart Wireless Gateway Network Settings Using the Field Communicator Rosemount 2051 Wireless Fast Key Sequence Configuring transmitter securityHart lock Reference Manual Commissioning Configuring Hart Lock using AMS Device Manager Configuring Hart Lock using Field CommunicatorConfiguration Button lock Calibration overview Operation and maintenance Determining necessary Sensor Trims Operation and Maintenance Reference ManualRecommended Calibration Tasks Transmitter Bench Calibration Tasks Field Calibration Tasks Determining calibration frequency Trimming with configuration buttons Calculate calibration frequency Sensor Trim Overview Trim the pressure signalExample HT = URV S/100 x P/1000 x LRV Sensor Trim example Sensor Trim Performing a Sensor Trim with a Field Communicator Select 5 Maintenance Select 1 Pressure CalibrationPerforming a Sensor Trim with AMS Device Manager Performing a Digital Zero Trim option DZ Line Pressure Effect Range 2 and Range Recall Factory Trim-Sensor TrimCompensating for Line Pressure Range 4 and Range Zero Effect LT = 500 + 0.01/10005001200 506 inH2O 1.26 bar Startup Screen Sequence LCD Screen Messages S R 13 0 Diagnostic Button Screen Sequence T w k K n w n Network Diagnostic Status Screens C H N G Operation and maintenance I l u r Device Diagnostic Screens C d e D i o I l u r N f g R n Troubleshooting Rosemount 2051 Wireless Device Status Information Troubleshooting Reference ManualDevice Status Description Recommended Action Check process for possible saturation condition Reference Manual Troubleshooting Check the buttons for obstructions Symptom Recommended Actions Rosemount 2051 Wireless TroubleshootingWireless Network Troubleshooting Removing from service Conformance to specification ±3σ Sigma Performance SpecificationsDigital output Total Performance Reference Accuracy1Appendix a Reference Data Reference Manual Models Standard Dynamic Performance Long Term StabilityLine Pressure Effect per 1000 psi 6,9 MPa1 Ambient Temperature Effect per 50F 28C ServiceMounting Position Effects Vibration Effect Range and Sensor Limits Wireless Self-Organizing Networks Overpressure limits Static pressure limit Temperature limitsBurst pressure limits Process Temperature Limits Volumetric DisplacementHumidity Limits 2051C Coplanar Electrical connections Physical specificationsProcess-Wetted parts Non-Wetted Parts Rosemount 2051L Process Wetted Parts Sensor Module Fill Fluid Table A-2. Transmitter weights without options Shipping Weights for 2051 Wireless Pressure TransmitterTable A-3 L weights without options Table A-4. Transmitter option weights Dimensional Drawings Pipe Process Lower Housing G Class Size Side F NPT Table A-5 L Dimensional SpecificationsOutside Extension Pipe Diameter Gasket Class Size Ordering Information Wireless Transmit Rate, Operating Frequency and Protocol Housing Material Conduit Entry SizeAntenna and SmartPower Manifold Assembly59 All-Welded Seal Assemblies for high vacuum applications9 Seal Assemblies9Mounting Bracket Product Certifications Software Configuration Hardware AdjustmentsPressure Testing Cleaning Process Area Max Static Line Pressure RC1/4 RC1/2 Process ConnectionSurface Finish Toolkit Total System Performance Reports Options Wireless Sensor Module Zero/Span AdjustmentCalibration Certification Process Area8 Typical Model Number 2051T G 5 X 2A 2 1 P WA3 WP5 B4 M5 Code Process Connection Size Material Extension Length ModelMounting Flange Size, Rating, Material High Side Low Pressure Side Flange Configuration Adapter Calibration Certification Standard Bolting Material StandardMaterial Traceability Certification Standard Software Configuration Standard Hardware Adjustments StandardToolkit Total System Performance Reports Standard Ring Material Number Size NPT Standard Line Size Model Product DescriptionPipe I.D. Range Piping Orientation Pipe Material / Mounting Assembly MaterialAnnubar Type Sensor Material Transmitter Housing Material Conduit Entry Size Temperature MeasurementOpposite Side Support or Packing Gland Isolation Valve for Flo-Tap Models QC1 Fluid and O-ring Options Standard Material Type Primary Element TechnologyPrimary Element Type Transmitter Housing Material ANSI/ASME B31.1 ANSI/ASME B31.3 ANSI/ASME B31.8 Process Connection Body MaterialOrifice Plate Material Bore Size Option Differential Pressure Ranges Options LCD Display Hardware Adjustments Standard Options Output information Configuration buttonsDisplay and interface options Bolts for flanges and adapters Rosemount 2051C Traditional Flange bracket options Spare parts Approved manufacturing locations Wireless CertificationsEuropean directive information Telecommunication compliance North American certifications Ordinary location certification for FMCSA Canadian Standards Association European certifications 注意！ 134 Field Communicator menu trees Appendix C Field Communicator Menu Trees and Fast Keys Appendix C Field Communicator Menu Trees Reference Manual Guided Setup 137 138 Effective range Appendix D Network design best practices Appendix D Network design best practices Appendix D Network design best practices Reference ManualPage Latin America