Direct mode | Escort 3004B, 3016B, 3008B specification

8Direct mode

Stop: condition for stopping the plotting

-Manual: with the Record key

-Trigger: with an association of the analogical or logical channels see Chapter 6 Trigger

-Wait for : after a delay or at a precise date and time

-Paper length: after writing a programmed length of paper

After end of plot: action after the end of the plotting; only possible if the start and stop triggers are not Manual

-Stop: no action

-Rearm: waiting for the start trigger

-Change Setup.: loading a configuration and waiting for the start trigger

Save Data: simultaneous saving of the measurements in internal memory or on a file

-No save: no simultaneous saving

-Memory: recording in internal memory

-Acquisition period: sampling speed of the channels

-Blocks: dividing the internal memory into blocks

-File: recording on a file

-File name: place and name of the saving file

-Acquisition period: sampling speed of the channels

See chapter File mode to know the limitations of the file recording

Trigger: condition for stopping the simultaneous saving in internal memory only

-Direct: the same as for paper printing

-Manual: with the Record key

-Trigger: with an association of the analogical or logical channels see Chapter Trigger

-Pre-triggering: position of the trigger in the memory (in the block)

Following: actions after the end of the simultaneous acquisition into the memory

-Save on file: saving the acquisition into a file

-Plot: writing the simultaneous acquisition into the memory

-Rearm.: reloading the writing; waiting for the start condition again

If a speed before start has been programmed, the paper will be fed at this rate while waiting the trigger.

The user can urge the trigger at any time by pressing the "Start/Stop" key again while waiting for the start

While plotting, pressing this key will stop the plotting

In case of power failure while plotting, the recorder will start again in the same status (waiting or writing)

Page 4

Image 62

Escort 3004B, 3016B, 3008B user manual Direct mode

Contents

Recorders Page Page Page Garanty Page Contents Diagrams Inputs / Outputs Appendix Page Security instructions Symbols and definitionsImportant Information Important informations See chapter Technical specifications Symbols that appear in this manualSymbols that appear on the appliance Conformity and restrictions of the appliance Presentation Presentation Presentation Rear side or top side Escort 3016B and Escort 3004B Front side Description of the screen Keys Thumb Wheel Updating the Internal Software F1 Modify Initialisation and Precautions of USE Initialisation Initialisation Storage precautions of the records Fuse Initialisation Power up of Escort 3008B Configuration on POWER-UP Initialisation Power up of Escort 3016B and Escort 3004B Measure of voltage Measure of temperature with a thermocoupleMeasure of temperature with a PT100 Measure of intensity Connection of the grounding Unplug the appliance before any intervention Routine maintenanceCalibration of the offsets Menu key Calibration Offset Factory adjustement Menu key Reload Factory Coeff Initialisation and precautions of use Mode key Use Help key Set up key Use Chart key Escort 3008B recorder only Channels set up key Analogical channels Use Use Logic channels Channel on/off key Vertical or horizontal sweep on screen Display Ft oscilloscope modeDisplay key Use  Y channel Direction keysUse Display XY Digital display Trigger key Replay key  Blocks and Files Start/Stop key Paper-feed key Diagrams Diagrams Positions of the channels Change diagrams Trigger key, parameters Start and Stop TriggersTriggers Single / Several thresholds Triggering with analogical channels Single threshold Triggers Several thresholds Triggers Trigger according to thresholds Triggers Trigger according to the slope Triggering with logical channels Mathematical calculations Mathematical CalculationsDefinitions Types of calculations Low MinimumMaximum High Cyclical RMS Width  V Direct mode Direct ModeConfiguration of the plotting Direct mode Triggering plotting Direct mode Example of plotting program Rearmament of the plottingWriting data  Channels set up key Memory mode Memory ModeConfiguration Triggering of the acquisition Trigger Sampling periodManual with the F2 key Urge triggering Internal memory, blocks Triggering position Double Trigger mode Recording Memory mode Memory mode Memory output Memory mode 10 Go/Nogo mode 10. GO/NOGO ModeConfiguration and triggering of the acquisition Memory Mode Creation of the frame 10 Go/Nogo mode Use of the frame Channels for Go/Nogo selected in the Trigger File mode File ModeConfiguration and start of the acquisition Ascii file LimitsBinary file File mode File management File ManagementGeneral Management of the configuration files Saving the configuration files Press the Load from disk key File management Loading the configuration filesManagement of the acquisition files Saving the acquisitions Real time PC Software for Analysis File management Loading the acquisition files File management File transfer with FTP File management Display with Escortview File management ESCORTview Myfile.rec /x Printing with Escort 3016B and Escort 3004B Plot set up and launchReplay , key Setup Plot Printing Printing Printer Setup Printing Inputs / Outputs Supplementary input / output connectorInputs / Outputs Pin no Input or Ouput Plotting and display Logical inputs13.1.1.Use External clock Keyboard input Alarm outputsPower supply output 13.1.2.Use 14.8. RS232 Mouse inputXGA screen output Not used. Reserved to future applications USB Interface Ethernet RJ45 interface Ethernet interface Ethernet InterfaceInterface Ethernet Syntax of a reception message Programming languageFormat of the reception messages Syntax of a message unit Data Ethernet interface Format of the emission messages Standard instructions Text data Indication of the status of the appliance Structure of the status data Registers of service request Status register Validation register Registers of standard events Register of the alarms Using the structure of status data Example Setup Programming dictionary Ethernet interface Parameters of the channels CHAnnel Current function Changing modeFunctions of the channels and between the channels Ethernet interface Chart Header Parameters Examples Directplot Triggerings Starttrig Ethernet interface Triggers Header Parameters Examples Triglog P1 Reloadings, real-time savings MEMSpeed Ethernet interface Launching plotting and recording RECord Ethernet interface Direct display Replay memory output Error messages Ethernet interface Service request Ethernet interface Technical Specifications Isolated inputs Bandwidth Technical specifications Temperature recordingSampling Multiplexed inputs Type of measurements Supplementary inputs / outputs Calibre Paper Alarm outputsExternal power supply Display Miscellaneous File acquisitionCommunication interface Environmental conditions Escort 3008B Technical specifications Dimensions, weight Environmental conditions Escort 3016B & Escort 3004B Electromagnetic compatibility Accordance test Internal saving battery Items furnished with the appliance Accessory items16.13.2 Optional accessory items 16.13.3 Expandable items Appendix AppendixInformation about the ranges of the inputs Voltage-type inputs Appendix Thermocouple J type input Thermocouple K type input Appendix Thermocouple T type input Thermocouple S type input Appendix Thermocouple B type input Thermocouple E type input Appendix Thermocouple N type input Thermocouple W5 type input Accuracy of the thermocouple measurements Example of Accuracy Calculation Slope V/ C Temperature CAccuracy of the PT100 measurements Accuracy class index of class