Hansol Multitech Uromat 3000 instruction

2.16 Installing the Grid – Replacing the Grid

Lift up the tabletop (CFC panel) (Fig. 27/Pos. 1), it will be held by the gas spring.

Move the tabletop towards the back and remove the front Nirosta panel. Move the tabletop towards the front and remove the rear Nirosta panel. Remove the left (Fig. 27/Pos. 3) and right (Pos. 4) cover panels. Remove the screws for the spiral cable guide panel and remove the cable guide panel. Move the tabletop longitudinally, remove the 6 mounting screws in the polycarbonate panel (Pos. 2) and remove the polycarbonate panel towards the front.

Switch the unit to the service mode, the green LED on the controller will go on and stay on. Press the Store and Reset buttons on the controller simultaneously, the three memory LED’s on the controller will blink green and the LED on the controller will blink very rapidly.

The cassette Bucky can now be moved slowly forward and backward using the Recall and Reset buttons.

Move the Bucky into the exposure position using the Recall button. Remove the mounting brackets (Fig. 28/ Pos. 2). Insert the grid with the focus mark facing up and secure it in place with the mounting brackets. Reinstall the polycarbonate panel (Fig. 27Pos. 2).

2.17 Installing the Tilt Angle Display- Error Display

Place the unit base cover panel (Fig. 29/Pos. 1) on the unit base. Guide the cable (Pos. 2) into the conduit (Pos. 3), install the tilt angle display (Pos. 4) and plug in the connector. Secure the plug-in connector with cable ties.

Fig. 29

Fig. 30

0116 7201

-46 of 90 -

06/00

Rev. 00 © 2000 Hans Pausch Röntgengerätebau Graf -Zeppelin-Str. 1 D-91056 Erlangen ALL RIGHTS RESERVED Ru

Image 46

Hansol Multitech Uromat 3000 Installing the Grid Replacing the Grid, Installing the Tilt Angle Display- Error Display

Contents

Installation Instructions Uromat Contents Technical Maintenance AdjustmentsNot configured Component Dimensions General Safety InformationComponent Weights Packaging Dimensions and Weights Component Designations Dimensional Drawing, Right-handed Version FFA Dimensional Drawing, Left-handed Version FFA 345 Drehachse Dimensional Drawing for Floor Mounting, Left-handed Version 0116 06/00 Required Test Equipment Power Line Connection DataRequired Special Tools Conditions for Transport and Storage Circuit Diagram, Contents of Circuit Diagram 06/00 0116 Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Collimator connection System Location Component Function Component Designations for the Circuit DiagramUromat LED1 +A6 Terminal strip for Bucky Cassette box motor potentiometer Function Description of the Controller Boards CPU Board Breaker Board Footswitch Board Control Unit Display Board Preparations for Mounting Unpacking the Unit Removing the Unit from the Pallet Installing the Unit Column Aligning the Unit Column Temporarily Connecting Line Power Installing the Tube Unit Support Arm Preinstalling the Tube Unit Collimator Combination Installing the Image Intensifier Laying the Collimator Cables Laying the High Voltage Cables To lay cables in the unit, 7 meters are requiredPage Making the Power Connection through the Generator Laying the I.I. Cable Installing the Measuring Chamber Installing the Grid Replacing the Grid Installing the Tilt Angle Display- Error Display Installing the Cover Panels Installing the Monitor Support Arm Option Installing the Mount for the Flush Bowl Sealing the Table Frame Cover Panel Adjustment Tube Unit Support Arm Central Beam Center Central Beam Center of BuckyLengthwise to the tabletop, for this Movement Path Potentiometer, Tabletop longitudinal Bucky Cassette Tray Movement Path Potentiometer Movement Path Potentiometer, Tabletop transverseI.I. Carriage System Potentiometer Potentiometer 1 Table Tilt Movement Path Potentiometer 2 Table Tilt Movement Path Tabletop Longitudinal Safety Switch Tabletop Transverse Safety Switch Not configured Table Up Movement Path Switch Strike Plate Bucky Movement Path Safety Switch13 I.I. Carriage Movement Path Safety Switch Table Down Movement Path Switch Strike Plate 17 +88 Tilt Movement Safety Switch 16 -20 Tilt Movement Safety SwitchSpindle Nut Safety Limit Switch Tabletop longitudinal Belt Tension Accessory Sensor SwitchesRaise-Lower Tabletop Belt Tension Cassette Carriage Drive Belt Tension Operation in the Service Mode Equipment Setting Parameters Procedure Adjusting the Axes Startup Collimator Basic Setting Cassette Format Setting the Collimator to the Cassette and I.I. FormatFormat Saving the Parameters in the PC Electronic Adjustment Parameters Setup Parameters Tabletop long. Store yes/no 1/0 Technical Maintenance Mechanical and Electrical Checks Preparations Page Function Check Page 176 Spare Parts, Overview 41/43 40/41 /10 Spare Parts, Unit Column Right-handed, Left-handed Versions 122 125 11 119 120 121 151 Spare Parts, Table Frame Tabletop, Right-handed Version 128 135 185 136 Spare Parts, Table Frame Tabletop, Left-handed Version Spare Parts, Tube Unit Support Right-handed Version 193 191 213 209 202 203 191 192 197 194 193 198 201 207 / 210 209 207 / 210 Spare Parts, Tube Unit Support Left-handed Version Spare Parts, Accessories 249 155 156 Spare Parts List Pos Designation Pos Designation Pos Designation Pos Designation Pos Designation Troubleshooting Error Cause Corrective Measure NumberPage Board Replacement Version Update Maintenance Verification Location of Identification Labels Labeling Max kg/ 66 lb Overview of Labels