Board Replacement, Version Update | Hansol Multitech Uromat 3000

6. Board Replacement

All boards are connected to each other by connectors and are replaceable. After they have been replaced correctly, they should perform a self test after power is switched on and log themselves into the CPU.

The CPU board and breaker board are accessible after opening the URO cover panel. They are seated on several round snap-on mounts, each of which musts be pressed through. The footswitch board is accessible only after opening the metal housing.

The control unit with spiral must be completely replaced.

The display with connection cable must be completely replaced.

Do not disconnect plug-in connections that are under voltage!

7. Version Update

Only the software of the CPU board can be updated to the latest version. The software in the other board cannot be updated.

The update is performed by replacing the EPROM on the processor module.

EPROM's are CMOS components. Please observe the guidelines for EMI protection.

0116 7201	-86 of 90 -	06/00
Rev. 00 © 2000 Hans Pausch Röntgengerätebau	Graf -Zeppelin-Str. 1	D-91056 Erlangen ALL RIGHTS RESERVED Ru

Image 86

Hansol Multitech Uromat 3000 installation instructions Board Replacement, Version Update

Contents

Installation Instructions Uromat Contents Not configured AdjustmentsTechnical Maintenance Component Dimensions General Safety InformationComponent Weights Packaging Dimensions and Weights Component Designations Dimensional Drawing, Right-handed Version FFA Dimensional Drawing, Left-handed Version FFA 345 Drehachse Dimensional Drawing for Floor Mounting, Left-handed Version 0116 06/00 Required Test Equipment Power Line Connection DataRequired Special Tools Conditions for Transport and Storage Circuit Diagram, Contents of Circuit Diagram 06/00 0116 Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Circuit Diagram, Collimator connection Uromat Component Designations for the Circuit DiagramSystem Location Component Function LED1 +A6 Terminal strip for Bucky Cassette box motor potentiometer Function Description of the Controller Boards CPU Board Breaker Board Footswitch Board Control Unit Display Board Preparations for Mounting Unpacking the Unit Removing the Unit from the Pallet Installing the Unit Column Aligning the Unit Column Temporarily Connecting Line Power Installing the Tube Unit Support Arm Preinstalling the Tube Unit Collimator Combination Installing the Image Intensifier Laying the Collimator Cables Laying the High Voltage Cables To lay cables in the unit, 7 meters are requiredPage Making the Power Connection through the Generator Laying the I.I. Cable Installing the Measuring Chamber Installing the Grid Replacing the Grid Installing the Tilt Angle Display- Error Display Installing the Cover Panels Installing the Monitor Support Arm Option Installing the Mount for the Flush Bowl Sealing the Table Frame Cover Panel Adjustment Tube Unit Support Arm Lengthwise to the tabletop, for this Central Beam Center of BuckyCentral Beam Center Movement Path Potentiometer, Tabletop longitudinal I.I. Carriage System Potentiometer Movement Path Potentiometer, Tabletop transverseBucky Cassette Tray Movement Path Potentiometer Potentiometer 1 Table Tilt Movement Path Potentiometer 2 Table Tilt Movement Path Tabletop Longitudinal Safety Switch Tabletop Transverse Safety Switch Not configured Table Up Movement Path Switch Strike Plate Bucky Movement Path Safety Switch13 I.I. Carriage Movement Path Safety Switch Table Down Movement Path Switch Strike Plate Spindle Nut Safety Limit Switch 16 -20 Tilt Movement Safety Switch17 +88 Tilt Movement Safety Switch Raise-Lower Tabletop Belt Tension Accessory Sensor SwitchesTabletop longitudinal Belt Tension Cassette Carriage Drive Belt Tension Operation in the Service Mode Equipment Setting Parameters Procedure Adjusting the Axes Startup Collimator Basic Setting Format Setting the Collimator to the Cassette and I.I. FormatCassette Format Saving the Parameters in the PC Electronic Adjustment Parameters Setup Parameters Tabletop long. Store yes/no 1/0 Technical Maintenance Mechanical and Electrical Checks Preparations Page Function Check Page 176 Spare Parts, Overview 41/43 40/41 /10 Spare Parts, Unit Column Right-handed, Left-handed Versions 122 125 11 119 120 121 151 Spare Parts, Table Frame Tabletop, Right-handed Version 128 135 185 136 Spare Parts, Table Frame Tabletop, Left-handed Version Spare Parts, Tube Unit Support Right-handed Version 193 191 213 209 202 203 191 192 197 194 193 198 201 207 / 210 209 207 / 210 Spare Parts, Tube Unit Support Left-handed Version Spare Parts, Accessories 249 155 156 Spare Parts List Pos Designation Pos Designation Pos Designation Pos Designation Pos Designation Troubleshooting Error Cause Corrective Measure NumberPage Board Replacement Version Update Maintenance Verification Location of Identification Labels Labeling Max kg/ 66 lb Overview of Labels