Glossary | HP L10, Intrusion Prevention System S10 specification

120Glossary

Image 122

HP L10, Intrusion Prevention System S10 manual Glossary

Contents

Hewlett-Packard SureStore E Hub Models S10 and L10 Page Hewlett-Packard SureStore E Hub Models S10 and L10 Denotes ServiceGrounding Hazard that can cause Contents Troubleshooting Contents Glossary Index Figures Page Tables TablesPage Product Description Overview Features Front Panel, Model S10 Short-Wave Hub Front Panel, Model L10 Long-Wave Hub Front Panel Display, Long-Wave Hub Rear Panel, Short-Wave and Long-Wave Hubs Fan air vents Supported Topologies Single Short-Wave Hub Topology Cascaded Short-Wave Hub Topology Maximum distance between server and FC-AL device = 1500 m Cascaded Long-Wave Hub Topology Supported Topologies Installation Overview Procedure 1 Prepare to Install the Hub Procedure 2 Unpack the Hub Procedure 3 Verify Hub Operation Etc/ping hub IP address Example /etc/ping Procedure 4 Mount the Hub into a Rack Optional Front of rack Rear of rack Installing the Hub into the Rack Plenum shroud Bracket Hub Correctly Installed in a Rack Procedure 5 Plan the FC-AL Connections Correct Cabling Example for a Short-Wave Hub Correct Cabling Example for a Long-Wave Hub Cascaded Long-Wave Hub Configuration Long-Wave Hub a Incorrect Cabling Examples Incorrect Cabling Example Disconnected Cable Not connected Do not attach more than one cable between any two hubs Nonsupported Cabling Example Nonsupported Cabling Example More Than Two Hubs Connected Procedure 6 Connect FC-AL Devices Installation For HP NetServers Procedure 7 Verify the ConnectionsFor HP-UX servers Ioscan -f RS-232 Interface Functions Child Hub if any ParameterParent Hub Parent Hub Child Hub if any Reset hub and run self-testAbout the RS-232 Main Menu RS-232 Interface Functions Management options Tips for Using the RS-232 InterfaceSet Networking parameters Hub information Setting Up an RS-232 Connection Setting Up a Connection to a PC Setting Up a Connection to a Dumb Terminal Configure the terminal to use the following settings Updating the Hub Firmware Procedure 1 Obtain the Current Firmware Procedure 2 Reboot the Hub Procedure 3 Update the Hub Controller Firmware Immediately press Enter to display the Boot menu After a few minutes, the transfer prompt appears for example Procedure 4 Update the Hub Device Agent Code IFCH3821.FRM Procedure 5 Reset the Hub Procedure 6 Set Manufacturing Values Enter 6 to display the Proxy Master menu Enter 3 to display the Set System OID Menu Enter Set System OID Menu appears with the new setting Setting Hub IP Address and Network Configuration Options Enabling Hub Management Verifying and Setting Snmp Values RS-232 Interface Functions Configuring Cascaded Hubs Configuring the Parent Hub Configuring the Child Hub Enabling Hub Management Connecting the Hubs Running Diagnostic Tests Chassis constitute a hazard Viewing Hub Information Viewing Hub Information Troubleshooting Troubleshooting Procedures Troubleshooting Label Color LED IndicatorsLED Pattern Indication LED Pattern Label Color Indication 10Base-T Flashing green Hub is valid If the Power LED Is Off If the Hub Fault LED Stays on After Self-Test Symptom Fan module is not firmly seated. Reinstall the fan module If a Fan Is Not Operating Hub is faulty. Replace the hub Troubleshooting Cable is bent or broken. Replace the cable Hub port is faulty. Replace the hubIf a Port LED Is Off If a Port LED Is On When It Should Be Off If the Management Server Cannot Ping the Hub If Firmware Upgrade Appears to Fail Hub-Controller version 03.06 is now loaded into RAM Recovering from Failed Firmware Upgrade Reinstalling the Hub Device Agent Code IFCH3720.FRM Reinstalling the Hub Controller Firmware IFCH3718.FRM Then the Main menu appears If Firmware Upgrade Appears to Fail Maintenance and Replacement Introduction Maintenance Replacing the Fan Module Introduction Maintenance Maintenance and Replacement Replacing the Fan Module Fan module Removing the Fan Module Replacing the Fan Module Reference Standard Configurations Product Number Description HP SureStore E Hub, Standalone Installed FC Port covers Configuration Options Option Description Sheet metal nuts ScrewsRails Nylon retainers Replacement Parts Short-wave 1005-0624 long-wave A4839-63001 Reference Replaceable Part Service Part Number Cable Description Customer Order Number Description Physical and Cabling Requirements Operating RequirementsSoftware and Operating System Requirements Model S10 Short-Wave Hub 101 Cable Plant SpecificationsSpecification Units Value Multimode graded index Supported Hardware 103 Supported Distances 105 Operating Requirements 107 Environmental SpecificationsEnvironment Limitations Physical Characteristics of Standalone Hub Reference Documents Installation DocumentsAdministration/Troubleshooting Documents Fibre Channel Technology Documents IEC Statement Worldwide Regulatory StatementsFCC Statement For U.S.A. Only Spécification ATI Classe a France 111 Product Noise Declaration GermanyAcoustic Noise Emissions Vcci Statement Japan 113 Laser SafetyCertification and Classification Information Usage Restrictions Laser Safety Finland LaserturvallisuusProduct Information To be performed on any OLM model 115 Declaration of Conformity Device Arbitrated LoopChild Hub Enclosure Link Fibre ChannelFibre Channel Arbitrated Loop FC-AL Long Wave Parent Hub NPortNPort Identifier Short Wave Glossary Index 121 NumericsCables See also hub configuring 60 definition 60 Hardware Index LEDs See also hub Index Set System OID menu displaying URL Voltage Index Reader Comment Sheet Agree Disagree Business Reply Mail B9574799875bPage Manual Part Number