Index | HP Intrusion Prevention System S10, L10 specification

menus Boot 50

Hub Information 65 Management Options 60 Manufacturing Settings 54 Network Setup 58 Proxy Master 54, 61, 62 Set sysDescr String 54 Set System OID 55

tips for using 44 troubleshooting 79

MIB-2 system name value 59

models 92

mounting ear brackets, part number 98

N

Network Setup menu displaying 58

nodes

dynamic recognition of 13 nylon retainers, part number 98

O

OmniBook. See PC

operating system requirements 100 overview

Fibre Channel Manager 12 hub 12

P

parent hub See also hub configuring 60 definition 60, 119

part numbers 97 parts

replacement 97

PC

setting up a connection to 45 pinging the hub

installation 26 troubleshooting 78

plenum shroud

installing in rackmount hub 29 part number 98

plug-and-play capabilities 13 port covers 87

port LED

troubleshooting 69, 70, 75, 77 ports

bypass persistence setting 56 bypassed by Fibre Channel Manager 76 long-wave hub 15

short-wave hub 14 treatment of 87

power connector long-wave hub 15 short-wave hub 14

power cord troubleshooting 72

power failure caution 49

power LED

during self-test 25, 31 long-wave hub 15 short-wave hub 14 troubleshooting 70, 72

power line 25, 107 product numbers 92 prompt

not displayed 79 Proxy Master menu

displaying 54, 61, 62

R

rackmount kit 92, 98 assembly 27

rackmounting the hub 27 rail

installing in rack 28 part number 98

rail nuts, part number 98 rail screws, part number 98 rear panel 16

Index

Index 125

Image 127

HP Intrusion Prevention System S10, L10 manual Index

Contents

Hewlett-Packard SureStore E Hub Models S10 and L10 Page Hewlett-Packard SureStore E Hub Models S10 and L10 Hazard that can cause ServiceGrounding Denotes Contents Troubleshooting Contents Glossary Index Figures Page Tables TablesPage Product Description Overview Features Front Panel, Model S10 Short-Wave Hub Front Panel Display, Long-Wave Hub Front Panel, Model L10 Long-Wave Hub Fan air vents Rear Panel, Short-Wave and Long-Wave Hubs Single Short-Wave Hub Topology Supported Topologies Maximum distance between server and FC-AL device = 1500 m Cascaded Short-Wave Hub Topology Cascaded Long-Wave Hub Topology Supported Topologies Installation Overview Procedure 1 Prepare to Install the Hub Procedure 2 Unpack the Hub Procedure 3 Verify Hub Operation Etc/ping hub IP address Example /etc/ping Procedure 4 Mount the Hub into a Rack Optional Front of rack Rear of rack Installing the Hub into the Rack Plenum shroud Bracket Hub Correctly Installed in a Rack Correct Cabling Example for a Short-Wave Hub Procedure 5 Plan the FC-AL Connections Correct Cabling Example for a Long-Wave Hub Cascaded Long-Wave Hub Configuration Long-Wave Hub a Incorrect Cabling Example Disconnected Cable Not connected Incorrect Cabling Examples Do not attach more than one cable between any two hubs Nonsupported Cabling Example More Than Two Hubs Connected Nonsupported Cabling Example Procedure 6 Connect FC-AL Devices Installation Ioscan -f Procedure 7 Verify the ConnectionsFor HP-UX servers For HP NetServers RS-232 Interface Functions Parent Hub ParameterChild Hub if any RS-232 Interface Functions Reset hub and run self-testAbout the RS-232 Main Menu Parent Hub Child Hub if any Hub information Tips for Using the RS-232 InterfaceSet Networking parameters Management options Setting Up a Connection to a PC Setting Up an RS-232 Connection Setting Up a Connection to a Dumb Terminal Configure the terminal to use the following settings Updating the Hub Firmware Procedure 2 Reboot the Hub Procedure 1 Obtain the Current Firmware Immediately press Enter to display the Boot menu Procedure 3 Update the Hub Controller Firmware After a few minutes, the transfer prompt appears for example IFCH3821.FRM Procedure 4 Update the Hub Device Agent Code Procedure 5 Reset the Hub Enter 6 to display the Proxy Master menu Procedure 6 Set Manufacturing Values Enter Enter 3 to display the Set System OID Menu Set System OID Menu appears with the new setting Enabling Hub Management Setting Hub IP Address and Network Configuration Options Verifying and Setting Snmp Values RS-232 Interface Functions Configuring Cascaded Hubs Configuring the Child Hub Configuring the Parent Hub Enabling Hub Management Connecting the Hubs Chassis constitute a hazard Running Diagnostic Tests Viewing Hub Information Viewing Hub Information Troubleshooting Troubleshooting Procedures Troubleshooting Indication LED IndicatorsLED Pattern Label Color Hub is valid LED Pattern Label Color Indication 10Base-T Flashing green If the Power LED Is Off Symptom If the Hub Fault LED Stays on After Self-Test If a Fan Is Not Operating Fan module is not firmly seated. Reinstall the fan module Hub is faulty. Replace the hub Troubleshooting If a Port LED Is Off Hub port is faulty. Replace the hubCable is bent or broken. Replace the cable If a Port LED Is On When It Should Be Off If the Management Server Cannot Ping the Hub Hub-Controller version 03.06 is now loaded into RAM If Firmware Upgrade Appears to Fail Recovering from Failed Firmware Upgrade IFCH3720.FRM Reinstalling the Hub Device Agent Code IFCH3718.FRM Reinstalling the Hub Controller Firmware Then the Main menu appears If Firmware Upgrade Appears to Fail Introduction Maintenance Replacing the Fan Module Maintenance and Replacement Introduction Maintenance and Replacement Maintenance Fan module Replacing the Fan Module Removing the Fan Module Replacing the Fan Module Reference Product Number Description Standard Configurations HP SureStore E Hub, Standalone Port covers Installed FC Option Description Configuration Options Nylon retainers ScrewsRails Sheet metal nuts Short-wave 1005-0624 long-wave A4839-63001 Reference Replacement Parts Cable Description Customer Order Number Replaceable Part Service Part Number Description Model S10 Short-Wave Hub Operating RequirementsSoftware and Operating System Requirements Physical and Cabling Requirements Specification Units Value Cable Plant Specifications101 Multimode graded index 103 Supported Hardware Supported Distances 105 Operating Requirements Environment Limitations Environmental Specifications107 Physical Characteristics of Standalone Hub Fibre Channel Technology Documents Installation DocumentsAdministration/Troubleshooting Documents Reference Documents Spécification ATI Classe a France Regulatory StatementsFCC Statement For U.S.A. Only IEC Statement Worldwide Acoustic Noise Emissions Product Noise Declaration Germany111 Vcci Statement Japan Certification and Classification Information Laser Safety113 To be performed on any OLM model Laser Safety Finland LaserturvallisuusProduct Information Usage Restrictions 115 Declaration of Conformity Enclosure Arbitrated LoopChild Hub Device Long Wave Fibre ChannelFibre Channel Arbitrated Loop FC-AL Link Short Wave NPortNPort Identifier Parent Hub Glossary Cables NumericsIndex 121 See also hub configuring 60 definition 60 Index Hardware See also hub LEDs Index Set System OID menu displaying Voltage URL Index Agree Disagree Reader Comment Sheet B9574799875b Business Reply MailPage Manual Part Number