Printhead Replacement, Snap-lock | Intermec PF4I specs

Chapter 11—Maintenance

Printhead Replacement, cont.

3

4

Pull the printhead bracket away from

Remove any media and transfer ribbon . the magnet in the pressure arm.

5

6

Snap-lock

Disconnect the printhead bracket from the print mechanism as indicated by the arrows and pull out the printhead as far as the cables allow.

Disconnect the cables from the print- head. Note the snap-lock on the inner connector. Pull at the connectors—not at the cables!

104 Intermec EasyCoder PF4i Compact Industrial—User’s Guide (Fingerprint)

Image 118

Intermec PF4I manual Printhead Replacement, Snap-lock

Contents

User’s Guide Page Document Change Record Version Date Description of Change GS Notice Germany FCC Notice United States of AmericaDOC Notice Canada EU Standard EN 55022 The European Union Declaration of Conformity CE EMCPage Contents Media Load Setting Up the PrinterThermal Transfer Printing Maintenance Setup ModeIntermec Shell Startup Program Adjustments Intermec Supplies Safety Summary Before You Begin Safety Icons Warranty Information Web Support Telephone Support Global Services and SupportRelated Documents Page Introduction Description of EasyCoder PF4i Compact Industrial Safety Summary Introduction Installation Unpacking the Printer Front View Rear View Media Compartment Description Media Supply Roll Post Media Supply Positions Print Mechanism Computer PowerConnections RS-232 Serial Interface uart1 Controls and Indicators Indicator Lamps Display Keyboard Beeper Starting Up Startup Files Memory Card Switching On the Printer Custom-Made Application Program Media Load Tear-Oﬀ Straight-through Tear-Oﬀ, Route the media through the print Tear-Oﬀ, Tear-Oﬀ with Quick-Load Straight-through Tear-Oﬀ with Quick-Load, Narrow Guides Rail Notch Wide Guides Tear-Oﬀ with Quick-Load, Cut-Oﬀ Cut-Oﬀ, Will go Close the cutter while pulling at Peel-Oﬀ Self-strip Peel-Oﬀ, Post Center section Paths Peel-Oﬀ, External Supply Fan-fold Thermal Transfer Printing Ribbon Load Ribbon Load, Route the ribbon through the print Ribbon Tight Page Setting Up the Printer Dots/mm 203.2 dots/inch printhead Intermec Fingerprint DescriptionIntermec Direct Protocol Default Setup Ser-Com uart1 Reading the Current Setup Serial Communication Setup ParametersBaud Rate Stop Bits Character LengthParity Flow Control Receive Buﬀer New LineTransmit Buﬀer Start Adjust FeedadjustStop Adjust Recommended Feed Adjustments Adjustment Dots/mm Distance Type Dpi std Dpi option Inches Media Media Size Print Window Print Window 8 dots/mm standard printhead Media Type Paper Type Direct Thermal Printing Thermal Transfer Printing Testfeed Print DeﬁnesContrast Head Resistance Test Labels LSS Test Print SpeedLTS Label Taken Sensor Returning to Factory Default Setup Factory Default? Enter=Yes ESC=No Setup Mode Entering Setup Mode at Installation EasyCoder PF4i Compact Industrial with Intermec Shell Navigating in Setup Mode Starting point Setup Mode Serial Communication uart1 Intermec Fingerprint Setup Mode Feed Adjust Setup Mode Media Ribbon Factor Setup Mode Print Defs Print Defs Setup Mode Serial Communication uart2 option Setup Mode Serial Communication uart3 option Baudrate Setup Mode Network Communication net1 option Page Intermec Shell Startup Program Application Programs Reboot restarting the printer Other Facilities Starting with Intermec Shell Fingerprint Selecting an Application Selecting Other Facilities Reboot Intermec Shell v8.1 Overview Last selected Line Analyzer Line Analyzer Sel.port1-6 Line Analyzer Error56 Options Options Integral Liner Takeup Unit Side Doors and MegatopPaper Cutter Media Supply Hub CompactFlash Protection Plate Label Taken SensorReal Time Clock Special Printheads Interface Boards Page Troubleshooting Intermec Readiness Indicator Display Messages and LED Indications Troubleshooting Symptom Possible Cause Remedy Refer to Feed Maintenance Printhead Cleaning Printhead Cleaning, Insert most of the cleaning card under External Cleaning Cleaning the Media Guides Printhead Replacement Printhead Replacement, Snap-lock 105 Media Jams Cut off any damaged or wrinkled part Adjustments Narrow Media Label Stop Sensor Five clicks out 20 mm LSS Auto LSS Auto Gap or slot detection Printhead Pressure Ribbon Break Shaft LTS Test LTS AdjustLTS Label Taken Sensor LTS Value Technical Data Appendix A-Technical Data 117 8MB-1GB Media Speciﬁcations Core Media Roll SizeRoll 121 Non-Adhesive Strip Media Type SetupMedia ⇒ Media Width ⇒ Liner Self-Adhesive Strip⇒ Media Width including liner ⇒ Media Width excluding liner ⇒ Label Length Self-Adhesive Labels⇒ Label Width excluding liner ⇒ Label Gap 125 ⇒ Detection Slit Length ⇒ Copy Length⇒ LSS Detection Position ⇒ Detection Slit Height 127 ⇒ Black Mark Length ⇒ Black Mark Width⇒ Black Mark Y-Position 129 Page Interfaces Protocol RS-232 InterfaceInterface Cable USB Interface Bar Code Wand Interface Optional Interfaces Double Serial Interface Board Ieee 1284 Parallel Interface Board Intermec Supplies Economy Quality Direct Thermal MediaPremium Quality Europe North America Coated Papers Thermal Transfer MediaUncoated Papers Polyethylene Plastics Transfer Ribbons Bar Code Directions Bar Code Directions Recommended Paper Type Settings Europe 143 Recommended Paper Type Settings North America 145 Page Page 960581-02