back with the [TRACK STATUS] left at REC, you will be able to audition the sound just as it was actually recorded.
If you set the [TRACK STATUS] to PLAY and play- back without changing the EQ settings the EQ will be applied double, so remember to set the EQ value back to 0.
4.Applying an effect to the input sound as you record
You can apply the internal effect of the D8 to the instrument connected to the INPUT 1/2 jack, and record the sound that has been processed by the effect.
■Connecting the input device and adjusting the level
1Refer to “■ Connecting the input device and adjusting the level” (p.11, p.12), to connect the input device and adjust the level.
It is not possible to use the effect when recording digitally.
■Selecting the location at which the effect will be inserted
2 Press the [EFFECT ASSIGN] key | INPUT 1/2 |
several times to select INPUT 1/2 | MASTER |
(indicator lit). | EFFECT |
| |
| ASSIGN |
| E |
With a setting of INPUT 1/2, the internal effect will be inserted between the input and the EQ of the mixer channel whose [TRACK STATUS] is set to REC.
|
|
|
|
| FADER | ||
|
|
|
|
|
|
| OUTPUT |
INPUT |
| Effect |
| [EQ] |
|
| RecTrack |
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
HEQ LEQ
3Adjust the following effect settings while listening to the input sound of the instrument or other source.
Adjust the [TRIM] knob so that the effect (“E”) level meter does not light all the way to CLIP.
■Selecting the effect program
4Press the [EFFECT] key several times to access the display page for selecting an effect program, as shown below.
EG1:ROCK
EFFECT
E
5Rotate the [VALUE] dial to select an effect program.
■Editing the effect
6Each effect program consists of up to four effects.
(Refer to p.61) After pressing the [EDIT] key, press the [EFFECT] key several times to select the effect that you wish to edit.
DISTORT:oú 
EDITEFFECT
E
7Rotate the [VALUE] dial to specify whether the effect you selected in step 6 will be used “o” (on) or not
8Press the [
] key to select the effect parameter that you wish to edit. Pressing the [
] key will move to the next parameter, and pressing the [
] key will move to the previous parameter. (Refer to p.72)
TYPE:DISTú 
9Rotate the [VALUE] dial to modify the value.
■Saving the effect program
If you wish to use the edited effect program in this song, or to use it in more than one song as a gen-
An edited effect which has not been saved will be lost if you perform one of the following actions.
•Select another effect program
•Select another song
•Turn off the power
10Press the [EFFECT] key several times to make the display read “Ren→ ✽✽✽” (✽ is the effect program name).
RenùROCK
11Press the [
] key several times to move the cursor to the location where you wish to modify the name, and rotate the [VALUE] dial to enter alpha- betical characters or symbols to assign the desired name.
Ï is a special symbol. Once this display is modi- fied, it cannot be selected newly.
12 Press the [EFFECT] key to access the “Write→ U✽✽” display. (U indicates the user bank area, and ✽✽ is the effect number.)
WriteùU01?
EDIT | EFFECT |
| E |
13Rotate the [VALUE] dial to select the save destina- tion in which the effect program will be saved.
14Hold down the [
] key for approximately one sec- ond to save the effect program and its name. When the data has been saved, the display will indicate “Completed”.
Chapter 2 | Operation |
|
|
Recording
13
