21. TRACK STATUS

Track status select .....................................................

[PLAY, REC (ANALOG), REC (DIGITAL), Mute]

Selects the status of each track.

Each time you press the [TRACK STATUS] key, the function will change and the indicator color will change to show this.

PLAY (indicator lit green): The selected track can be played back.

REC (ANALOG) (indicator blinking/lit red): This can be selected when [REC SELECT] is INPUT 1/2 or MASTER. Audio from the external input jacks INPUT 1/2 or from the master bus can be recorded to the selected track. The indicator will blink during record- ready condition, and will light during recording (or rehearsal).

REC (DIGITAL) (indicator blinking/lit orange): This can be selected when [REC SELECT] is DIGITAL IN. The external input from the DIGITAL IN connector can be recorded to the selected track. The indicator will blink during record-ready condition, and will light during recording (or rehearsal).

It is not possible to input from the internal effect or from an external input via the AUX IN jacks.

MUTE (indicator off): The selected track will be muted.

When input monitor (refer to p.47) is set to AUTO, set- ting [TRACK STATUS] to REC will cause the EQ and fader to apply only to the input sound, so that the fader and EQ will not affect the playback sound of the track. Be aware that if you inadvertently change the fader or EQ settings during playback etc., the volume or EQ of the input sound will be affected.

However if [REC SELECT] is set to MASTER, it will be the same as when [TRACK STATUS] is set to PLAY; you will always hear the playback tracks, and faders and EQ will be valid.

22. EQ

P1 High EQ gain adjustment

1 2

HEQ1 :+00

P1-1 Channel number display...........................................

[1, 2, 3, 4, 5, 6, 1-2, 3-4, 5-6, 7-8]

This shows the currently selected channel number.

1-2, 3-4and 5-6will appear when Pairing is On (refer to PAIR On/Off).

P1-2HEQ (Fc=10 kHz) gain setting

[-15...+00...+15]

The boost/cut at the 10 kHz cutoff frequency can be adjusted over a range of -15–+15 dB.

P2 Low EQ gain adjustment

1 2

LEQ1 :+00

P2-1Channel number display ..................................

[1, 2, 3, 4, 5, 6, 1-2, 3-4, 5-6, 7-8]

This shows the currently selected channel number.

1-2, 3-4and 5-6will appear when Pairing is On (refer to PAIR On/Off).

P2-2LEQ (Fc=100 Hz) gain setting

[-15...+00...+15]

The boost/cut at the 100 Hz cutoff frequency can be adjusted over a range of -15–+15 dB.

High EQ and Low EQ can be paired (refer to PAIR On/ Off), and registered as part of a scene (refer to SCENE).

TRACK STATUS=REC Recording

FADER

INPUT [EQ]

TRACK

HEQ LEQ

TRACK STATUS=REC Playback

FADER

INPUT

[EQ]

TRACK

HEQ LEQ

TRACK STATUS=PLAY Playback

FADER

INPUT

[EQ]

TRACK

EQ and fader will apply to the input sound and will affect the recording

EQ and fader will not affect the playback

EQ and fader will apply to the playback

23. EFFECT SEND

P1 Effect send level (Snd) adjustment

Adjusts the level that is sent from after each channel fader (post fader) to the internal effect.

Adjust this setting when you use the internal effect.

When [REC SELECT] DIGITAL IN is selected, the internal effect will be off.

1 2

Snd1 :000

HEQ LEQ

Pairing (refer to PAIR On/Off) is also possible.

58

Page 57
Image 57
Korg D8 manual Track Status, 22. EQ, Effect Send