5. DISPLAY MODE

P1 Counter display selection

P1 Location counter display selection .......................

[MBT, MSM, MSF, FreeTime]

Selects the way in which the location counter will be displayed.

The display will change each time you press the [DIS- PLAY MODE] key.

6. REC MODE

Recording method select............................................

[Off, AutoPunch+RehearsalOn, AutoPunchOn, RehearsalOn]

Selects the recording method. The setting will alternate each time you press the [REC MODE] key.

Off (indicator off): Normal recording.

REHEARSAL

 

AUTO PUNCH

 

REC

 

MODE

MBT (Measure/Beat/Tick [1/96th of a beat]/Mark*): The location will be displayed in units of a measure from the beginning of the song.

The tempo and time signature for display are specified by TEMPO P1.

01:SngName

MSM (Minutes/Seconds/Milliseconds/Mark*): The absolute time from the beginning of the song will be displayed.

AutoPunch+Rehearsal (both indica- tors lit): Rehearsal for Auto Punch In/ Out recording will occur in the IN (LOC1)–OUT (LOC2) area for tracks whose [TRACK STATUS] is REC.

AutoPunch (indicator lit): Auto Punch In/Out recording will occur in the IN (LOC1)–OUT (LOC2) area for tracks whose [TRACK STATUS] is REC.

Rehearsal (indicator lit): Rehearsal* for recording will occur for tracks whose [TRACK STATUS] is REC.

REHEARSAL

AUTO PUNCH

REC

MODE

REHEARSAL

AUTO PUNCH

REC

MODE

REHEARSAL

AUTO PUNCH

REC

MODE

01:SngName

MSF (Minutes/Seconds/Frames [1/30th of a second]/ Mark*): The absolute time from the beginning of the song will be displayed. (For MTC synchronization)

01:SngName

FreeTime (Minutes/Seconds): The remaining time available for recording in the currently selected drive will be displayed. Normally, this indicates the avail- able time for monaural recording (one track). If you set two [TRACK STATUS] indicators to REC, the available time for stereo recording or simultaneous two-track recording will be displayed.

01:SngName

*“Mark” is when the cursor is displayed under the entire location counter. At this time, you can rotate the [VALUE] dial to move to a mark point that you have registered. (Refer to “Moving to a Mark point” p.24)

The counter display will change as follows only during program playback (refer to “EDIT PLAY MODE P3”).

Remaining song time

(Minutes/Seconds Millisecond [1/1000th of a second]) Elapsed song time

(Minutes/Seconds Millisecond [1/1000th of a second]) Total remaining playback time (Minutes/Seconds Millisecond [1/1000th of a second]) Total elapsed playback time

(Minutes/Seconds Millisecond [1/1000th of a second])

*When AutoPunch+Rehearsal or Rehearsal are selected, when you begin recording, the input mon- itor system (refer to SYSTEM P2) will operate in the same way as when recording, allowing you to rehearse the recording. Sound will not actually be recorded.

7.PLAY MODE

Playback method select .............................................

[Off, AutoPlayOn, AutoRepeatOn]

Selects the playback method. The setting will alternate each time you press the [PLAY MODE] key.

Off: Normal playback.

AutoPlayOn: Playback will occur between IN (LOC1) and OUT (LOC2)*, and will automatically stop at the OUT location.

You can also stop playback by pressing the [STOP] key.

AutoRepeatOn: Playback will occur repeat- edly between IN (LOC1) and OUT (LOC2)*. You can also stop playback by pressing the [STOP] key.

*If you perform Auto Punch In/Out when AutoPlayOn or AutoRepeatOn is selected, a “pre roll time” will be added before the IN location, and a “post roll time” will be added after the OUT loca- tion. (Refer to EDIT PLAY MODE P1, P2.)

For details on setting the IN and OUT locations, refer to “Storing a Locate point” (p.23).

Chapter 3

Reference

51

Page 50
Image 50
Korg D8 manual Display Mode, REC Mode, Play Mode, P1 Counter display selection