Marantz SR7005 Preparation, Speaker Detection, When performing Audyssey Auto Setup over again

SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH

Set up speakers (Audyssey® Auto Setup)

STEP 1

Preparation

4 Connect the setup microphone to the SETUP MIC jack of this unit.

When the setup microphone is connected, the following screen is displayed.

AUTO SETUP
AUDYSSEY AUTO SETUP	MultEQ XT

STEP1 Preparation	[1/6]
Connect the speakers
and place them accord-
ing to the recommenda-
tions in the manual.
Set the following
items if necessary.
Amp Assign
Channel Select
Auto Setup Start
ENTER Enter		RETURN Cancel
Start Auto Setup

This screen provides the method for setting up 7.1-channel playback using surround back speakers. For the method of setting up speakers other than the 7.1-channel system, select “Amp Assign” and perform step 3 and 4 of “Set up “Amp Assign”” (vpage 54).

If unused channels are set with “Channel Select”, measuring time can be shortened. For setting, perform steps 5 to 9 of “Set up “Channel Select”” (vpage 54).

5 Use uito select “Auto Setup Start” and then press ENTER.

STEP 2

Speaker Detection

•In STEP 2, you will perform measurements at the main listening position.

•This step automatically checks the speaker configuration and speaker size, and calculates the channel level, distance, and crossover frequency. It also corrects distortion in the listening area.

6 Select “Measure” and then press

ENTER.

When measuring begins, a test tone is output from each speaker.

• Measurement requires several minutes.

7 The detected speakers are displayed.

AUTO SETUP
AUDYSSEY AUTO SETUP	MultEQ XT

STEP2 Spkr Detect Check		[2/6]
Front	Yes
Center	Yes
Subwoofer	Yes
Surround	Yes
S.Back	2spkrs
F.Height	No
F.Wide	No

Retry

Next Measurement

ENTER Enter RETURN Cancel

Go to Step 3 (Measurement) after speaker check

NOTE

If a connected speaker is not displayed, the speaker may not be connected correctly. Check the speaker connection.

8 Use ui to select “Next 1

Measurement” and then press ENTER.

NOTE

If “Caution” is displayed:

Go to “Error messages” (vpage 11), check any related items, and perform the necessary procedures.

If the problem is resolved, return and restart “Audyssey Auto Setup”.

When performing Audyssey Auto Setup over again

Press uito select “Retry”, and then press ENTER.

When measuring has stopped

Press RETURN, to the “Cancel Auto Setup?”

prompt is displayed.

Press o to select “Yes”, then press ENTER.

Setting up the speakers again

Repeat the operation from step 4 of

STEP1 Preparation .

STEP 3

Measurement

•In STEP 3, you will perform measurements at multiple positions (two to eight positions) other than the main listening position.

•You can achieve a more effective correction of distortion within the listening area by performing measurements at multiple positions.

9 Move the setup microphone to position 2, use ui to select “Measure”, and then press ENTER.

The measurement of the second position starts. Measurements can be made in up to eight positions.

AUTO SETUP
AUDYSSEY AUTO SETUP	MultEQ XT

STEP3 Measurement	[3/6]
Please place the mic-
rophone at ear height
at 2nd listening
position.
Measure
Next Calculation
ENTER Enter		RETURN Cancel

Start next measurement. Test Tone will start

If you want to omit measurements from the next position onward, select “Next 1 Calculation”.

(Go to STEP4 Calculation )

10Repeatto 8. step 9, measuring positions 3

When measurement of position 8 is completed, a “Measurements finished.” message is displayed.

AUTO SETUP
AUDYSSEY AUTO SETUP	MultEQ XT

STEP3 Measurement	[3/6]
Measurements finished.
Retry
Next Calculation
ENTER Enter		RETURN Cancel
Proceed to Step 4 (Analyze)

Simple version

Basic version

Advanced version

Information

Remote control operation	Move the cursor	Confirm the setting	Return to previous menu	9
buttons	(Up/Down/Left/Right)