Marantz SR7005 manual Set up speakers, Set up Amp Assign, Set up Channel Select

ENGLISH

Set up speakers

This section provides the setup methods of speaker systems other than the 7.1-channel system (with surround back speakers).

For the setup methods of the 7.1-channel system with surround back speakers, see “Simple version”, “Set up speakers (Audyssey® Auto Setup)” (vpage 7) of “Simple version”.

First install and connect the speakers to this unit.

Before Auto Setup measurement, the settings shown below can be made.

•Changing the amplifier assignment (Amp Assign)

The signal output from the SURR.BACK/AMP ASSIGN speaker terminal of this unit can be switched to match your speaker environment (vpage 54 “Set up “Amp Assign””).

•Setting the channels to be used (Channel Select)

If channels that are not to be used are set in advance, measurement for the set channels is skipped, and measuring time can be reduced (vpage 54 “Set up “Channel Select””).

1	Set up the	2 Connect the setup microphone.
	remote control unit

nn Set up the operation mode

Press AMP to set the remote control unit to amplifier operation mode.

When the setup microphone is connected, the following screen is displayed.

AUTO SETUP
AUDYSSEY AUTO SETUP	MultEQ XT

Press AMP	STEP1 Preparation	[1/6]
	and place them accord-
	Connect the speakers
	ing to the recommenda-
	tions in the manual.
	Set the following
	items if necessary.
	Amp Assign
	Channel Select
	Auto Setup Start
	ENTER Enter		RETURN Cancel
	Start Auto Setup

3 Set up “Amp Assign”

Use ui to select “Amp Assign”, and then press ENTER.

AUTO SETUP
AUDYSSEY AUTO SETUP	MultEQ XT

STEP1 Preparation	[1/6]
Connect the speakers
and place them accord-
ing to the recommenda-
tions in the manual.
Set the following
items if necessary.
Amp Assign
Channel Select
Auto Setup Start
ENTER Enter		RETURN Cancel

Set use of surround back ch. for your system

4 Use o p to select the configuration of the connected speakers, and then press RETURN.

Normal Set when using surround back, front height or front wide speakers. In this case, go to step 5.

ZONE2 Set for connecting the speakers for ZONE2 to the SURR. BACK/ AMP ASSIGN terminals.

ZONE3 Set for connecting the speakers for ZONE3 to the SURR. BACK/ AMP ASSIGN terminals.

SPKR-CSet for connecting a tweeter of a front speaker to the SURR. BACK/AMP ASSIGN terminals and a woofer of the front speaker to the FRONT terminals.

around items indicate the settings.

5 Set up “Channel Select”

Use ui to select “Channel Select”, and then press ENTER.

AUTO SETUP
AUDYSSEY AUTO SETUP	MultEQ XT

STEP1 Preparation	[1/6]
Connect the speakers
and place them accord-
ing to the recommenda-
tions in the manual.
Set the following
items if necessary.
Amp Assign
Channel Select
Auto Setup Start
ENTER Enter		RETURN Cancel

Skip unused ch’s measurement for timesaving

6 Use ui to select a channel.

Subwoofer Select for no subwoofers to be used. In this case, go to step 7.

Surround Select for no surround back

Back speakers to be used. In this case, go to step 8.

•“Surround Back” can be set when “Amp Assign” is set to “Normal”.

Front Select for no front height speakers Height to be used. In this case, go to step

9.

•“Front Height” can be set when “Amp Assign” is set to “Normal”.

Front Wide	Select for no front wide speakers to
	be used. In this case, go to step 9.

•“Front Wide” can be set when “Amp Assign” is set to “Normal”.

7 GWhen “Subwoofer” is selected in step 6H

Use o p to select the item.

Measure Set for measuring a subwoofer.

Skip Set for no measuring of a subwoofer.

54

Remote control operation	Move the cursor	Confirm the setting	Return to previous menu
buttons	(Up/Down/Left/Right)