ENGLISH
Set up speakers (Audyssey® Auto Setup)
STEP 4 | STEP 5 | STEP 6 | Finish |
Calculation | Check | Store | |
|
|
|
|
11On the STEP3 screen, use ui to select “Next 1 Calculation”, and then press ENTER.
Measuring results are analyzed, and the frequency response of each speaker in the listening room is determined.
AUTO SETUP |
|
AUDYSSEY AUTO SETUP | MultEQ XT |
STEP4 Calculation | [4/6] |
Now calculating... |
|
Please wait. |
|
25% |
|
•Analysis takes several minutes to complete. The time required for this analysis depends on the number of speakers connected.
The more connected speakers there are, the longer it takes to perform analysis.
12Use ui to select the item you want to check, and then press ENTER.
AUTO SETUP |
|
AUDYSSEY AUTO SETUP | MultEQ XT |
STEP5 Check | [5/6] | ||||||
Check processing res- |
|
|
|
|
|
|
|
ults. To proceed,press |
|
|
|
|
|
|
|
“Next” |
|
|
|
|
|
|
|
Spkr Config Check |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Distance Check |
|
|
|
|
|
|
|
Ch. Level Check |
|
|
|
|
|
|
|
Crossover Check |
|
|
|
|
|
|
|
Next Store |
|
|
|
|
|
|
|
ENTER Enter |
|
| RETURN Cancel | ||||
Select item to check |
|
|
|
|
|
|
|
•Subwoofers may measure a greater reported distance than the actual distance due to added electrical delay common in subwoofers.
•If you want to check another item, press
RETURN.
13Use ui to select “Next 1 Store” and then press ENTER.
NOTE
•If the result differs from the actual connection status, or if “Caution!” is displayed, see “Error messages” (vpage 11). Then carry out Audyssey Auto Setup again.
•If the result still differs from the actual connection status after remeasurement or the error message still appears, it is possible that the speakers are not connected properly. Turn this unit off, check the speaker connections and repeat the measurement process from the beginning.
•If you change speaker positions or orientation, perform Audyssey Auto Setup again to find the optimal equalizer settings.
14Select “Store” and then press ENTER. Save the measurement results.
AUTO SETUP |
|
AUDYSSEY AUTO SETUP | MultEQ XT |
STEP6 Store | [6/6] | |||||
Press “Store” to store |
|
|
|
|
| |
calculation results. |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Store |
|
|
|
|
| |
ENTER Enter | RETURN Cancel | |||||
Apply and store measurement result |
|
|
|
|
| |
AUTO SETUP |
|
AUDYSSEY AUTO SETUP | MultEQ XT |
STEP6 Store | [6/6] |
Now storing... |
|
Please wait. |
|
25% |
|
•Saving the results requires about 10 seconds.
•If the measuring results are not to be saved, press RETURN. A message “Cancel Auto Setup?” will be displayed. Press o then select “Yes”. All the measured Audyssey Auto Setup data will be erased.
NOTE
During saving of measurement results, be sure not to turn off the power.
15Unplug the setup microphone from the unit’s SETUP MIC jack.
16Set Dynamic Volume®.
AUTO SETUP |
|
AUDYSSEY AUTO SETUP | MultEQ XT |
Finish | [6/6] | |||||||||
Storing complete. |
|
|
|
|
|
| ||||
Auto Setup is now |
|
|
|
|
|
| ||||
finished. Please unplug |
|
|
|
|
|
| ||||
microphone. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Turn on Dynamic Volume? |
|
|
|
| ||||||
Yes | No | |||||||||
ENTER Exit
Turn Dynamic Volume on and exit Auto Setup
•For details of Dynamic Volume settings, see page 77.
nn When turning Dynamic Volume on
Use o to select “Yes“, and then press ENTER.
• The unit automatically enters “Evening” mode.
nn When turning Dynamic Volume off
Use p to select “No“, and then press ENTER.
NOTE
After performing Audyssey Auto Setup, do not change the speaker connections or subwoofer volume. In event of a change, perform Audyssey Auto Setup again.
10
Remote control operation | Move the cursor | Confirm the setting | Return to previous menu | |
buttons | (Up/Down/Left/Right) | |||
|
|
