Marantz SR7005 manual Hdmi Setup

ENGLISH

Manual Setup

Setting items	Setting details
Crossover Frequency	Crossover : Set the crossover frequency.
Set the maximum frequency	• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
of the bass signal output	250Hz
from each channel to	Advanced : Specify crossover frequency for each speaker.
the subwoofer. Set the
	• Front / Center / Surround / S.Back / F.Height / F.Wide : Select the
Crossover Frequency to
	speaker.
suit the bass reproduction
	• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
capability of the speaker
	250Hz : Set the crossover frequency.
being used.
	• “Crossover Frequency” can be set when the “Bass Setting” –
	“Subwoofer Mode” (vpage 81) setting is “LFE+Main”, or when you
	have a speaker that is set to “Small”.
	• Always set the crossover frequency to “80Hz”. When using small
	speakers, however, we recommend setting the crossover frequency to
	a higher frequency.
	• For speakers set to “Small”, sound below the crossover frequency
	is cut from the sound output. The cut bass sound is output from the

HDMI Setup	Default settings are underlined.
Make settings for HDMI video/audio output.
Setting items	Setting details
RGB Range	Normal : Output with RGB video range (16 (black) to 235 (white)).
Set the video range of RGB	Enhanced : Output with RGB video range (0 (black) to 255 (white)).
output from the HDMI	This setting is active when using a TV equipped with a DVI terminal.
connector.
Auto Lip Sync	ON : Compensated.
Make automatic	OFF : Not compensated.
compensation for timing
shift in audio and video
output.
HDMI Audio Out	AMP : Play back through speakers connected to the receiver.
Select HDMI audio output	TV : Play back through TV connected to the receiver.
device.	When the HDMI control function is activated, priority is given to the TV

audio setting (vpage 57 “HDMI control function”).

subwoofer or front speakers.

• The speakers that can be set when “Advanced” is selected differ

depending on to the “Subwoofer Mode” setting (vpage 81).

• When “LFE” is selected, speakers set to “Small” at “Speaker Config.”

can be set. If the speakers are set to “Large”, “Full Band” is displayed

and the setting cannot be made.

Monitor Out

Make settings for HDMI monitor output.

Monitor 1 : A TV connected to the HDMI OUT 1 terminal is always used.

Monitor 2 : A TV connected to the HDMI OUT 2 terminal is always used.

With “Resolution” (vpage 72) not set to “Auto”, check whether the TV you are using is compatible with the resolution under “HDMI Information” – “HDMI Monitor 1 Information” and “HDMI Monitor 2 Information” (vpage 90).

• If set to “LFE+Main”, this setting can be made regardless of the

speaker size.

HDMI Control

You can link operations with devices connected to HDMI and compatible with HDMI Control.

ON : Use HDMI control function.

OFF : Do not use HDMI control function.

•When a device that is not compatible with the HDMI control function is connected, set “HDMI Control” to “OFF”.

•Please consult the operating instructions for each connected component to check the settings.

•Refer to “HDMI control function” (vpage 57) for more information about the HDMI control function.

82

NOTE

• When “HDMI Control” is set to “ON”, it consumes more standby power. If you are not using this unit for an extended period, it is recommended that you unplug the power cord from the power outlet.

• “HDMI Control” does not work when the power to the equipment is off. Either turn power on or set to standby.

• The HDMI control function controls operations of a TV that is compatible with the HDMI control function. Make sure that the TV and HDMI are connected when you perform HDMI control.

• If the “HDMI Control” settings have been changed, always reset the power to connected devices after the change.

Remote control operation	Move the cursor	Confirm the setting	Return to previous menu
buttons	(Up/Down/Left/Right)