Marantz SR7005 manual nnAudyssey Settings, English, Audio/Video Adjust, Press DYN EQ/VOL

ENGLISH

Audio/Video Adjust

nnAudyssey Settings Default settings are underlined.

Set MultEQ® XT, Dynamic EQ® and Dynamic Volume®. These can be selected after Audyssey® Auto Setup has been performed. For additional information on Audyssey technology, please see page 111.

NOTE

If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup, you may not be able to select Dynamic EQ/Dynamic Volume, and “Run Audyssey” may be displayed.

In this case, either perform Audyssey Auto Setup over again or perform “Restore” (vpage 11) to return to the settings after Audyssey Auto Setup was run.

Setting items	Setting details
MultEQ XT	Audyssey : Optimize the frequency response of all speakers.
Select one equalizer from	Audyssey Byp.L/R : Optimize frequency response of speakers except
three modes. MultEQ XT	front L and R speakers.
corrects both time and	Audyssey Flat : Optimize frequency response of all speakers to flat
frequency response	response.
problems in the listening	Manual : Apply frequency response set with “Manual EQ” (vpage 78).
area based on Audyssey	OFF : Turn “MultEQ XT” equalizer off.
Auto Setup calibration. We
recommend “Audyssey”.	• “Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be
MultEQ XT is the
	selected after Audyssey Auto Setup has been performed. “Audyssey”
prerequisite function for
	is automatically selected after performing Audyssey Auto Setup. When
Dynamic EQ and Dynamic
	“Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is selected,
Volume.
	illuminates.

• After running Audyssey Auto Setup, if the Speaker Configuration, Distance, Channel Level, and Crossover Frequency have changed without increasing the number of speakers

measured, only illuminates.

• Pressing MULTEQ makes this setting.

NOTE

•“MultEQ XT” and “Manual” cannot be selected when “EQ Customize” is set to “Not Used” (vpage 83).

•When using headphones, “MultEQ XT” is automatically set to “OFF”.

Setting items			Setting details
Dynamic EQ®	ON : Use Dynamic EQ.
Solve the problem of	OFF : Do not use Dynamic EQ.
deteriorating sound quality
as volume is decreased	•	is displayed when set to “ON”.
by taking into account
human perception and	• Buttons on the remote control unit or main unit
room acoustics. Works with
MultEQ XT.		can be used for operations.
		Press DYN EQ/VOL.
		Each time DYN EQ/VOL is pressed, the setting is
		changed as shown below.
		Dynamic EQ : ON		Dynamic EQ : ON
		Dynamic Volume : Heavy		Dynamic Volume : Medium
		Dynamic EQ : OFF	Dynamic EQ : ON		Dynamic EQ : ON
		Dynamic Volume : OFF	Dynamic Volume : OFF		Dynamic Volume : Light
Reference Level Offset	0dB (Film Ref) : This is the default setting and should be used when
Audyssey Dynamic EQ is	listening to movies.
referenced to the standard	5dB : Select this setting for content that has a very wide dynamic range,
film mix level. It makes	such as classical music.
adjustments to maintain	10dB : Select this setting for jazz or other music that has a wider dynamic
the reference response	range. This setting should also be selected for TV content as that is usually
and surround envelopment	mixed at 10 dB below film reference.
when the volume is turned	15dB : Select this setting for pop/rock music or other program material
down from 0 dB. However,	that is mixed at very high listening levels and has a compressed dynamic
film reference level is not	range.

always used in music or	Setting is enabled when “Dynamic EQ” is “ON” (vpage 76).
other non-film content.
Dynamic EQ Reference
Level Offset provides three
offsets from the film level
reference (5 dB, 10 dB, and
15 dB) that can be selected
when the mix level of the
content is not within the
standard.

76

Remote control operation	Move the cursor	Confirm the setting	Return to previous menu
buttons	(Up/Down/Left/Right)