Marantz SR7005 manual Playback Advanced operation, Convenient functions, Hdmi control function

SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH

Playback (Advanced operation)

Simple

Playback (Basic operation) (vpage 26)

Selecting a listening mode (Surround mode) (vpage 46)

nn HDMI control function (vpage 57) nn Sleep timer function (vpage 58)

nn Adjusting the volume of the speakers (vpage 58)

nn Operating a wireless LAN-compatible mobile terminal to play music and still pictures (vpage 59)

nn Web control function (vpage 60) nn Panel lock function (vpage 62)

nn Various memory functions (vpage 62)

Convenient functions

HDMI control function

When you make an HDMI connection with a TV or player compatible with this unit and HDMI control functions, you can perform the following operations by setting the HDMI control function of each device.

nn This unit power off can be linked to the TV power off step.

nn You can switch audio output devices with a TV operation.

When you set “Output audio from amp” in the TV audio output setup operation, you can switch the amp power on.

nn You can adjust this unit volume in the TV volume adjustment operation.

nn You can switch this unit input sources through linkage to TV input switching.

nn When playing the player, this unit input source switches to the source for that player.

NOTE

•The HDMI control function only supports the HDMI OUT 1 connector. To use the HDMI control function, connect the television to the HDMI OUT 1 connector.

•When “HDMI Control” is set to “ON”, it consumes more standby power.

•The HDMI control function controls operations of a TV that is compatible with the HDMI control function. Make sure that the TV and HDMI are connected when you perform HDMI control.

•Some functions may not operate depending on the connected TV or player. Check the user guide of each device for details beforehand.

•When “Power Off Control” on the menu is set to “OFF” (vpage 83), this unit is not set to standby even if the connected device is in the standby mode.

•When connection changes are implemented, such as adding connections to HDMI devices, linked operations may be initialized. In this case, you will need to reconfigure the settings.

•When “HDMI Control” is set to “ON”, it is not possible to assign an HDMI connector to “TV” at “Input Assign” (vpage 71).

1 Set the HDMI output connector corresponding with the HDMI control function.

Set “HDMI Control” (vpage 82) to “ON“.

2 Turn the power on for all the equipment connected by HDMI cable.

3 Set the HDMI control function for all equipment connected by HDMI cable.

•Please consult the operating instructions for the connected equipment to check the settings.

•Carry out steps 2 and 3 should any of the equipment be unplugged.

4 Switch the television input to the HDMI input connected to this unit.

5 Switch this unit input to the HDMI input source and check if the picture from the player is ok.

6 When you turn the TV’s power to standby, check that the power of this unit also goes to standby.

If the HDMI control function does not operate properly, check the following points.

•Is the TV or player compatible with the HDMI control function?

•Is “HDMI Control” (vpage 82) set to “ON”?

•Is “Power Off Control” (vpage 83) set to “All” or “Video”?

•Are the HDMI control function settings of all equipment correct?

•Is the television connected to the HDMI OUT 1 connector?

NOTE

Should any of the operations below be performed, the interlocking function may be reset, in which case, repeat steps 2 and 3.

•“Input Assign” – “HDMI” (vpage 71) setting has changed.

•“Monitor Out” (vpage 82) setting is changed.

•There is a change to the connection between the equipment and the HDMI, or an increase in equipment.

version

Basic version

Advanced version

Information

57