Configuring a Remote Modem AT*RA | Motorola 3460 guide

3460 Fast’R

Configuring a Remote Modem (AT*RA)

You can set remote-modem parameter options and view remote-modem status from a local 3460 Fast’R with the AT*RA command. With this function, you can:

•Set up remote modems from a central network administration facility

•Monitor remote operation

•Troubleshoot remote-modem application problems

Remote configuration with AT*RA uses the main data channel, temporarily halting data transmission. It is not available when either modem is in direct (AT*SM0), synchronous, or leased line mode.

Initiate a remote-configuration session from a local modem, using a communications application, as follows. Both modems must be set to the RA1 option.

Running a Remote Configuration Session

Step

Stage

1.Establish a connection with the remote modem. Motorola recommends using a Reliable connection (AT*SM2 or AT*SM3)

2.Enter the remote-escape command to place the remote modem in escape mode.

The remote-escape command sequence is: guard time (AT&G, S-Register 42), remote-escape character sequence (S-Register 41), guard time.

The remote modem responds: RC ESTABLISHED.

3.If the remote modem has password security (AT*PE) enabled, enter the password: AT*ZIpassword.

4.Enter configuration or status commands.

Example: AT&V returns long-form status information.

The following commands are not supported in remote configuration mode: ATA, AT&T, ATD, ATH, action commands.

3-17

Image 69

Motorola 3460 manual Configuring a Remote Modem AT*RA, Running a Remote Configuration Session

Contents

Motorola Proprietary Material LGEN031@email.mot.comFast’R Advanced Modem Setup Basic Modem Setup Appendix B. Attention AT Commands Troubleshooting Problems and Improving PerformanceFast’RVu Appendix A. Regulatory Information Appendix C. Specifications Return Procedures IndexAppendix D. Four-Button/LCD User Interface Page Mise en Garde About This Guide IntroductionAudience Other Documentation ¡Precaución VorsichtAvertissement Warnung Windows TrademarksPage To Access the Motorola World-Wide Web Site Motorola Customer InformationTo Order Additional Motorola User Documentation Page Part Number T0022-01, Rev F Excellent Good Average Below Average Poor Business Reply Mail Chapter Hardware Installation Fast’R Installing a Stand-Alone Modem Installing a Stand-Alone ModemStep Action RJ11 Telco For two- or four-wire leased-line/dial-line modems For two-wire leased-line or dial-line modems Ferrite Bead Installation Transformer Modem Rear Panel and Cable Connections Safety and Operational Notices Power TransformerConnecting Ports Repair Lightning Checking AccessWay Enclosure Shipment Installing an AccessWay EnclosureSite and Power Preparation Computer Cable for Fast’RVu Cooling for Three or More Enclosures Cooling for One or Two Enclosures Cabinet Arrangement- Three or More Enclosures Fan and Deflector Requirements Selecting a Power Cord Group Country Power Cord and Plug Standards Countries Installing an AccessWay in an Equipment Rack Installing the Enclosure in an Equipment Rack Cabling an AccessWay Enclosure Cabling an AccessWay Enclosure Attached Motorola network management system NMS Cabling One or More Enclosures to a Computer Cabling Enclosures Together for Fast’RVuNMS or Fast’RVu First Enclosure Locations Second Enclosure Locations Third Enclosure LocationsFourth Enclosure Locations Modem Addresses in Multiple-Enclosure Configurations Installing a Modem Card Installing/Removing Modem CardsInstalling a Modem Card in an AccessWay Two-Wire Leased- or Individual telephone cable connectors, connect cables from Removing a Modem Card Removing a Modem Card from an AccessWay AC Power Module Power Modules DC Power Module Connecting to DC Power SupplyConnecting the AccessWay to DC Power Supply 12. Replace the power module 12. Power Module Alarm Circuit Switches 4 cm Tip for Power Module Setup Installing a Second DC Power Module Installing a Second DC Power Module Power Module Location Two Slots 14. Dual DC Power Module Locations Set-Up Installing a Modem Daughtercard, Vanguard EnclosurePage Before You Start Vanguard Daughtercard Setup Setting Up for Asynchronous Dial Operation Entering Commands to the ModemAsynchronous Operation Step Stage Leased-Line Synchronous Operation Basic Setup for Sync Leased-Line Operation Installing a Modem on a Windows Computer Fax Setup on Windows Install and run a fax application Page Chapter Advanced Modem Setup What is the Configuration? Modem Configuration and CommandsIssuing AT Commands Issuing Network Management Commands What Are Option Sets? Configuring a Modem for Async Operation Managing Option SetsSelecting and Customizing Option Set Configuring a Modem for Leased-Line Sync Operation Option-Set Parameter Default Options Pstn Signaling Threshold DTR DelayModulation Mode Data Transfer Mode AT Commands to Manage Option Sets Enter This AT Commands for Modem TasksAT Action Commands AT Action Commands Command & Option Description Dial Modifiers Description Dial Modifiers Non-Option Set Parameters Site-Specific Parameters Default Option Available Option Telco or Telco Jack Options Terminal OptionsDial Line Filter Dialing Options Remote Configuration Options Access Security OptionsOption Set Options Restoral Options Other Options DTR/ACU Password Verification on Connection Access Security Functions Configuration and Phone Number Access Restriction Security Parameters, Default Options Command Description Access Security AT Command SummaryOutbound Dial Restriction Quiet Answer Running a Remote Configuration Session Configuring a Remote Modem AT*RA Step Stage Network Management AT*NE Managing Remote Modems Managing Remote Modems in an AccessWay Enclosure Option Description AT*NP Parameter Options Parameter Option Comment Configuring Modems for RestoralAT*DI1=Low/Fast Dial line as soon as it connects Often the modem checks for loop Page Chapter Fast’RVu Closing Multiple Fast’RVu Windows Getting Started With Fast’RVu Specifying a Modem in Fast’RVu Language OptionsAdding a Display Language to Fast’RVu Specifying a Modem On Which to Operate Fast’RVu Fast’RVu main window, select Do This Useful Information Example Setting Callback to Phonebook Entry Viewing and Setting Modem Options Example Checking Device Status Checking Device, Circuit, and Signal Status This Command Submenu Lets You Entering Commands Example Copying a Configuration From One Modem to Another Executing Line and Modem Tests Example Executing a Bit Error Rate BER Test Network Management Override Using Fast’RVu to Communicate With a Remote Modem Problems During a Download Downloading Modem SoftwareDownloading Modem Software with Fast’RVu Troubleshooting Steps Chapter Troubleshooting Problems Improving Performance Installation Troubleshooting Actions Call Establishment Fast’R Data Mode Fast’R Call Termination File Transfer Mode LEASED-LINE Operation Test Description Command Running Diagnostic Tests This Appendix Appendix a EEC Directive Conformity For Pstn Operation in Portugal Fast’R Regulatory Marking Industry Canada Equipment Attachment Limitations Country Statutory Statements Canada Canadian Emission Statements Country Statutory Statements U. K FCC Part 68 Registration Information Country Statutory Statements U. S. a FCC Part 15 Emission Statements Fast’R Product Safety Regulatory Marking Command Option Description AT Command Set Speaker Volume Echo Async AT Commands to TerminalEnter On-Line Data Mode Busy Out Test Display Result Code Select Pulse DialingStore Value in S-Register Select Tone Dialing Commands Call-Answering Mode Break-Signal Receipt HandlingNo-Buffering Mode Select Connect Message Receive-Data Buffer Delay Default Telephone Number to Dial When DTR108=On Data Compression DTE Computer Port Rate Dial Wait Period Pause After Dialing Leased to Dial Threshold Data Mode for Direct Mode Automatically Redial Failed Calls Error Correction ProtocolTransmit Level for Dialed Calls Flow Control Protocol Dial to Leased Threshold Hold Dial Line Link Telephone Numbers Dial Line FilterLow-Speed Operation Protocol LXn Transmit Level for Leased-Line Calls Pstn Signaling Modulation ModeMinimum Rate Maximum Rate AT Message Network Control NC Address Buffer OptionDisplay Stored Telephone Number Secondary Channel Network Control Override Mode Network Control Pass Through Password Protection Lock Password Protection Enable/DisablePassword Protection Unlock Password Change Initiate/Terminate Restoral Abort Remote ConfigurationParity Restoral Auto-Redial Data Transfer Mode Auto RetrainModem Speed Bar Display Call Time-Out Test Restoral 25bis Character Code 25bis Synchronizing Idle Signal25bis Format 25bis Response Callback After Incoming Call Enter Access Security Group PasswordDial Restriction Require Remote Telephone Number DCD Control Verify Password DTR Control Guard Tone Re-Initialize Memory NowDisplay Modem ID Line Type Pulse Cycle CTS ControlDSR Control Test Clock Signal SourceStatus Message Save Changes Power Up in Option Set Service ClassSelect Phonebook Entry to Enter +FCR=n Receive Fax Data +FCLASS=n Service Class+FLO=n Fax Flow Control Manufacturer ID +FPR=n Serial Port Rate Software Revision Level Options Stored in Status S- Registers Command Default Register Parameter Value Description AT*DB3 Delay=S38 Pin 22, where asserted means Enable restoral indicator on EIARestoral is active Numeric Result Messages and CodesText Form Call Progress Result Codes Connect Message Result Codes, Reliable=Short ConnectConnect Message Result Codes, Reliable=Long Connect Reliable EC=x DC=y EC=x DC=y Test Pattern Result Code Miscellaneous Result CodesFax Class 1 Result Codes +F4Page Appendix C Modem Stand Daughter Property Card AccessWay Alone Physical CharacteristicsPhysical Properties Vanguard Data Operation Operating ModesFax Operation Standards Modulation Modes Condition Modem Card AccessWay Alone Condition Modem Card AccessWay Stand-AloneEnvironmental Limits Operating Conditions Electromagnetic Compatibility AC Power Supply Module AccessWay Enclosure Power Supply and Power RequirementsDC Power Supply Module AccessWay Enclosure Power and Modem Operation AccessWay Enclosure and Network Management Interface RJ-11 Connectors and InterfacesPin Function Interface RJ-21X Computer Interface Pin-outs Signal Number Circuit Function PinFunction RJ-11 Interface Pin-outs Function Mass-Termination Interface Pin-outsPin Function Power Interface Power Type Connector Changing a Configuration With the OLC ButtonNetwork Management Interface Pin-outs Pin Two-Wire Function Four-Wire Function Pin SignalNetwork Management Interface Pin-outs Interface RJ-11 Connection Type Dial Line Pin Function Computer Interface Pin Circuit Function Stand-Alone Modem Connectors and Interfaces Interface RJ-11 Connection Type Telephone Pin Function LINE* Connector NMS OUT Network Management Interface Pinouts Requirement at Main Characteristic Supply Modem Input Power Requirements Status LEDs Light Bars Figure D-2. Stand-Alone Modem Front Panels Figure D-3. Card Modem Front Panels Status LEDs Status LED DisplaysOff Light Bar Displays This Indicates Light Bars 326X Leased-Line Operation Note CompatibilityPage Appendix D Menu Organization-Categories Parameters, and Options Configuration OPT’S LCD Display Using the Front-Panel User InterfaceControl Buttons Front-Panel Control Buttons Enter Down Equipment Return Procedures Return Procedures IntroductionCase of Damage To Return Equipment For locations Contact Packaging Guidelines for Equipment Return Factory Repair Numerics Symbols INDEX-2 INDEX-3 INDEX-4 INDEX-5 INDEX-6 INDEX-7 INDEX-8 INDEX-9 INDEX-10 INDEX-11 INDEX-12