Option-Set Parameter Default Options | Motorola 3460 specs

3460 Fast’R

Option-Set Parameter Default Options

This section lists the pre-configured option-set parameter options.

Table 3-1. Option-Set Default Options

	Pre-Configured Default Option
	Option Set 1	Option Set 2
Command	(Asynchronous)	(Synchronous)

Async Echo	ATE1=On	ATE1=On1
Result Code	ATQ0=Enable	ATQ0=Enable1
Result Form	ATV1=Verbose	ATV1=Verbose1
Longspace Disconnect	ATY1=On	ATY0=Off
DCD Control	AT&C0=High	AT&C1=Normal
DTR Control	AT&D2=Disconnect	AT&D0=High
Line	AT&L0=Dial	AT&L1=2W Lease
AT Form	AT&M0=Async	AT&M1=Sync Data1
CTS Control	AT&R0=Async/Sync	AT&R1=Normal
Remote Access	AT&RA1=On	AT&RA1=On
DSR Control	AT&S0=High	AT&S1=Normal
Clock	AT&X0=Internal	AT&X0=Internal
ACU Protocol	AT*AC1= AT	AT*AC0=None
Adaptive Rate	AT*AP1=On	AT*AP1=On
V.34 Asymmetric Rate	AT*AR1=On	AT*AR1=On
Answer Restoral	AT*AS0=LL FAIL	AT*AS0=LL FAIL
Break Handling	AT*BK0=Destructive	AT*BK0=Destructive1
Mode	AT*CA0=Orig	AT*CA0=Orig
Direct Mode Async	AT*CL2=10 bits	AT*CL2=10 bits
Character Length
Connect Message	AT*CM0=DTE Rate	AT*CM0=DTE Rate1
Default Dial	AT*DA0=Off	AT*DA0=Off1
DTE (Terminal) Rate	AT*DE23=Auto	AT*DE23=Auto
Lease to Dial	AT*DI0=Low/Fast	AT*DI0=Low/Fast
Threshold

Parameters and options shown shaded gray vary by country. For details, refer to Appendix B of the 3460 Fast’R Reference Guide .

1Parameter option does not affect normal operation.

3-6

Image 58

Motorola 3460 manual Option-Set Parameter Default Options

Contents

Motorola LGEN031@email.mot.com Proprietary MaterialFast’R Basic Modem Setup Advanced Modem Setup Fast’RVu Troubleshooting Problems and Improving PerformanceAppendix B. Attention AT Commands Appendix A. Regulatory Information Return Procedures Index Appendix C. SpecificationsAppendix D. Four-Button/LCD User Interface Page Audience About This Guide IntroductionMise en Garde Other Documentation Avertissement Vorsicht¡Precaución Warnung Trademarks WindowsPage Motorola Customer Information To Access the Motorola World-Wide Web SiteTo Order Additional Motorola User Documentation Page Excellent Good Average Below Average Poor Part Number T0022-01, Rev F Business Reply Mail Chapter Hardware Installation Fast’R Step Action Installing a Stand-Alone ModemInstalling a Stand-Alone Modem RJ11 Telco For two-wire leased-line or dial-line modems For two- or four-wire leased-line/dial-line modems Ferrite Bead Installation Modem Rear Panel and Cable Connections Transformer Power Transformer Safety and Operational NoticesConnecting Ports Repair Lightning Site and Power Preparation Installing an AccessWay EnclosureChecking AccessWay Enclosure Shipment Computer Cable for Fast’RVu Cooling for One or Two Enclosures Cooling for Three or More Enclosures Fan and Deflector Requirements Cabinet Arrangement- Three or More Enclosures Selecting a Power Cord Power Cord and Plug Standards Countries Group Country Installing the Enclosure in an Equipment Rack Installing an AccessWay in an Equipment Rack Cabling an AccessWay Enclosure Cabling an AccessWay Enclosure Attached Motorola network management system NMS Cabling Enclosures Together for Fast’RVu Cabling One or More Enclosures to a ComputerNMS or Fast’RVu Third Enclosure Locations First Enclosure Locations Second Enclosure LocationsFourth Enclosure Locations Modem Addresses in Multiple-Enclosure Configurations Installing a Modem Card in an AccessWay Installing/Removing Modem CardsInstalling a Modem Card Two-Wire Leased- or Individual telephone cable connectors, connect cables from Removing a Modem Card from an AccessWay Removing a Modem Card Power Modules AC Power Module Connecting to DC Power Supply DC Power ModuleConnecting the AccessWay to DC Power Supply 12. Replace the power module 12. Power Module Alarm Circuit Switches Tip for Power Module Setup 4 cm Installing a Second DC Power Module Installing a Second DC Power Module 14. Dual DC Power Module Locations Power Module Location Two Slots Installing a Modem Daughtercard, Vanguard Enclosure Set-UpPage Vanguard Daughtercard Setup Before You Start Asynchronous Operation Entering Commands to the ModemSetting Up for Asynchronous Dial Operation Step Stage Basic Setup for Sync Leased-Line Operation Leased-Line Synchronous Operation Fax Setup on Windows Installing a Modem on a Windows Computer Install and run a fax application Page Chapter Advanced Modem Setup Issuing AT Commands Modem Configuration and CommandsWhat is the Configuration? Issuing Network Management Commands What Are Option Sets? Managing Option Sets Configuring a Modem for Async OperationSelecting and Customizing Option Set Configuring a Modem for Leased-Line Sync Operation Option-Set Parameter Default Options Modulation Mode Threshold DTR DelayPstn Signaling Data Transfer Mode AT Action Commands AT Commands for Modem TasksAT Commands to Manage Option Sets Enter This AT Action Commands Command & Option Description Dial Modifiers Dial Modifiers Description Site-Specific Parameters Default Option Available Option Non-Option Set Parameters Dial Line Filter Terminal OptionsTelco or Telco Jack Options Dialing Options Option Set Options Access Security OptionsRemote Configuration Options Restoral Options DTR/ACU Other Options Access Security Functions Password Verification on Connection Configuration and Phone Number Access Restriction Outbound Dial Restriction Access Security AT Command SummarySecurity Parameters, Default Options Command Description Quiet Answer Configuring a Remote Modem AT*RA Running a Remote Configuration Session Step Stage Network Management AT*NE Managing Remote Modems in an AccessWay Enclosure Managing Remote Modems AT*NP Parameter Options Option Description AT*DI1=Low/Fast Configuring Modems for RestoralParameter Option Comment Dial line as soon as it connects Often the modem checks for loop Page Chapter Fast’RVu Getting Started With Fast’RVu Closing Multiple Fast’RVu Windows Adding a Display Language to Fast’RVu Language OptionsSpecifying a Modem in Fast’RVu Specifying a Modem On Which to Operate Fast’RVu Fast’RVu main window, select Useful Information Do This Viewing and Setting Modem Options Example Setting Callback to Phonebook Entry Checking Device, Circuit, and Signal Status Example Checking Device Status Entering Commands This Command Submenu Lets You Example Copying a Configuration From One Modem to Another Example Executing a Bit Error Rate BER Test Executing Line and Modem Tests Using Fast’RVu to Communicate With a Remote Modem Network Management Override Downloading Modem Software Problems During a DownloadDownloading Modem Software with Fast’RVu Chapter Troubleshooting Problems Improving Performance Troubleshooting Steps Troubleshooting Actions Installation Call Establishment Fast’R Data Mode Fast’R Call Termination File Transfer Mode LEASED-LINE Operation Running Diagnostic Tests Test Description Command Appendix a This Appendix EEC Directive Conformity For Pstn Operation in Portugal Fast’R Regulatory Marking Country Statutory Statements Canada Industry Canada Equipment Attachment Limitations Canadian Emission Statements Country Statutory Statements U. K Country Statutory Statements U. S. a FCC Part 68 Registration Information FCC Part 15 Emission Statements Fast’R Product Safety Regulatory Marking AT Command Set Command Option Description Enter On-Line Data Mode Echo Async AT Commands to TerminalSpeaker Volume Busy Out Test Store Value in S-Register Select Pulse DialingDisplay Result Code Select Tone Dialing Commands No-Buffering Mode Break-Signal Receipt HandlingCall-Answering Mode Select Connect Message 108=On Default Telephone Number to Dial When DTRReceive-Data Buffer Delay Data Compression Dial Wait Period Pause After Dialing DTE Computer Port Rate Data Mode for Direct Mode Leased to Dial Threshold Transmit Level for Dialed Calls Error Correction ProtocolAutomatically Redial Failed Calls Flow Control Protocol Hold Dial Line Dial to Leased Threshold Low-Speed Operation Protocol Dial Line FilterLink Telephone Numbers LXn Transmit Level for Leased-Line Calls Modulation Mode Pstn SignalingMinimum Rate AT Message Maximum Rate Buffer Option Network Control NC AddressDisplay Stored Telephone Number Network Control Override Mode Secondary Channel Network Control Pass Through Password Protection Unlock Password Protection Enable/DisablePassword Protection Lock Password Change Parity Abort Remote ConfigurationInitiate/Terminate Restoral Restoral Auto-Redial Auto Retrain Data Transfer ModeModem Speed Bar Display Test Restoral Call Time-Out 25bis Format 25bis Synchronizing Idle Signal25bis Character Code 25bis Response Dial Restriction Enter Access Security Group PasswordCallback After Incoming Call Require Remote Telephone Number Verify Password DCD Control DTR Control Display Modem ID Re-Initialize Memory NowGuard Tone Line Type CTS Control Pulse CycleDSR Control Status Message Clock Signal SourceTest Save Changes Service Class Power Up in Option SetSelect Phonebook Entry to Enter +FLO=n Fax Flow Control +FCLASS=n Service Class+FCR=n Receive Fax Data Manufacturer ID Software Revision Level +FPR=n Serial Port Rate Command Default Register Parameter Value Description Options Stored in Status S- Registers Delay=S38 AT*DB3 Enable restoral indicator on EIA Pin 22, where asserted meansRestoral is active Text Form Result Messages and CodesNumeric Call Progress Result Codes Connect Message Result Codes, Reliable=Long ConnectConnect Message Result Codes, Reliable=Short Connect Reliable EC=x DC=y EC=x DC=y Fax Class 1 Result Codes Miscellaneous Result CodesTest Pattern Result Code +F4Page Appendix C Physical Properties Physical CharacteristicsModem Stand Daughter Property Card AccessWay Alone Vanguard Fax Operation Standards Operating ModesData Operation Modulation Modes Environmental Limits Condition Modem Card AccessWay Stand-AloneCondition Modem Card AccessWay Alone Operating Conditions Electromagnetic Compatibility DC Power Supply Module AccessWay Enclosure Power Supply and Power RequirementsAC Power Supply Module AccessWay Enclosure Power and Modem Operation AccessWay Enclosure and Network Management Pin Function Connectors and InterfacesInterface RJ-11 Interface RJ-21X Pin Computer Interface Pin-outs Signal Number Circuit FunctionFunction Mass-Termination Interface Pin-outs RJ-11 Interface Pin-outs FunctionPin Function Changing a Configuration With the OLC Button Power Interface Power Type ConnectorNetwork Management Interface Pin-outs Network Management Interface Pin-outs Pin SignalPin Two-Wire Function Four-Wire Function Interface RJ-11 Connection Type Dial Line Pin Function Stand-Alone Modem Connectors and Interfaces Computer Interface Pin Circuit Function LINE* Connector Interface RJ-11 Connection Type Telephone Pin Function Network Management Interface Pinouts NMS OUT Power Requirements Requirement at Main Characteristic Supply Modem Input Figure D-2. Stand-Alone Modem Front Panels Status LEDs Light Bars Figure D-3. Card Modem Front Panels Status LED Displays Status LEDsOff Light Bars Light Bar Displays This Indicates Compatibility 326X Leased-Line Operation NotePage Appendix D Configuration OPT’S Menu Organization-Categories Parameters, and Options Control Buttons Using the Front-Panel User InterfaceLCD Display Front-Panel Control Buttons Down Enter Case of Damage Return Procedures IntroductionEquipment Return Procedures To Return Equipment For locations Contact Factory Repair Packaging Guidelines for Equipment Return Symbols Numerics INDEX-2 INDEX-3 INDEX-4 INDEX-5 INDEX-6 INDEX-7 INDEX-8 INDEX-9 INDEX-10 INDEX-11 INDEX-12