|
|
|
| Troubleshooting |
|
|
|
| |
|
| Cause | Action | |
| 0251 System CMOS | System CMOS configuration | ξ Reconfigure the system CMOS | |
| checksum | is changed. |
| by using BIOS setup. |
| configuration used |
| ξ Clear system CMOS using | |
|
|
|
| hardware jumper. |
| 0252 Password checksum | Password is cleared. | ξ | Reconfigure by using BIOS |
| bad |
|
| setup. |
|
|
| ξ | Clear system CMOS using |
|
|
|
| hardware jumper. |
| 0260 System Timer error | System Timer is faulty. | Reconfigure by using BIOS setup. | |
| 0270 Real time clock error | RTC is faulty. |
|
|
| 0271 Check date and time | Date and time are incorrectly |
|
|
| setting | set. |
|
|
| 02D0 System cache error - | CPU cache is faulty. | If replacing the CPU does not | |
| Cache disabled |
| help, replace the CPU/IO module. | |
| 02D1 System Memory | CPU cache is faulty. |
|
|
| exceeds the CPU's |
|
|
|
| caching limit |
|
|
|
| 0613 COM A configuration | COM A configuration is faulty. | If restarting does not help after | |
| change |
| resetting the setting to default by | |
| 0614 COM A config, error - | Device constructing COM A is | using BIOS setup, replace the | |
| device disable | faulty. | CPU/IO module. | |
| 0B28 Unsupported | Unsupported CPU is mounted. | Check the supported CPU and | |
| Processor detected on |
| replace it. If this does not help, | |
| Processor 1 |
| replace the CPU/IO module. | |
| 0B29 Unsupported | Unsupported CPU is mounted. |
|
|
| Processor detected on |
|
|
|
| Processor 2 |
|
|
|
| 0B60 DIMM group #1 has | DIMM is faulty. | Replace DIMM Group#1. | |
| been disabled |
|
|
|
| 0B61 DIMM group #2 has |
| Replace DIMM Group#2. | |
| been disabled |
|
|
|
| 0B62 DIMM group #3 has |
| Replace DIMM Group#3. | |
| been disabled |
|
|
|
| 0B70 The error occurred | I2C pass is faulty. | Replace the part that relevant | |
| during temperature | Sensor is faulty. | sensor is mounted. | |
| sensor reading |
|
|
|
| 0B71 System Temperature | Temperature is abnormal. | Check if fan is faulty or clogging | |
| out of the range | Fan is abnormal. ᴾ | has occurred. If there is no | |
|
|
| problem, replace CPU/IO module. | |
| 0B74 The error occurred | I2C pass is faulty. | Replace the part that relevant | |
| during voltage sensor | Sensor is faulty. | sensor is mounted. | |
| reading |
|
|
|
| 0B75 System voltage out of | Voltage is abnormal. | If turning AC power off and on | |
| the range |
| does not help, replace the | |
|
|
| CPU/IO module. | |
| 0B80 BMC Memory Test | RMC device is faulty. | Replace the CPU/IO module or ft | |
| Failed |
| Remote Management Card | |
| 0B81 BMC Firmware Code |
| (option). | |
| Area CRC check failed |
|
|
|
| 0B82 BMC core Hardware |
|
|
|
| failure |
|
|
|
