Manuals / Nortel Networks / Communications / Telephone

Nortel Networks BCM50 manual To connect a power supply using a UPS

Models: BCM50

1 246

Download 246 pages 27.36 Kb

Page 101

Chapter 9 Connecting the cables to the BCM50 system 101

Figure 44 Connect a UPS

UPS

Main unit

USB	hub	USB cable

Power supply

If your BCM50 system does not have a UPS, proceed to “To connect a power supply without a UPS”.

To connect a power supply using a UPS

1Mount the UPS within 1.5 meters (5 feet) of the BCM50 units.

The UPS must be close enough to the BCM50 units that the power supply can be connected to both the UPS and the BCM50 units.

2Plug one end of the USB cable into the USB port on the UPS.

For information about the location of the ports on the UPS, refer to the UPS documentation.

3Plug the other end of the USB cable into the USB hub.

4Plug one end of the second USB cable into the USB hub.

5Plug the other end of the second USB cable into the USB port on the main unit.

6Plug the UPS power cord into the ac power source (wall outlet).

7Proceed to “Connecting the lines and extensions” on page 102.

To connect a power supply without a UPS

1Unpack the new power supply.

2Check the power supply for damage. If you find any damage, contact your Nortel representative.

Warning: Do not use the power supply if the power supply cord or power supply cable is damaged.

3Rotate the retention clip so the power outlet is open.

4Plug the power supply cord into the BCM50 unit.

BCM50 Installation and Maintenance Guide

Image 101

Nortel Networks BCM50 manual To connect a power supply using a UPS, To connect a power supply without a UPS

Contents

BCM50 Installation and Maintenance Guide N0027152 Copyright Nortel Networks LimitedSoftware License BCM50 Installation and Maintenance GuideNortel Networks Task List Installing the main unitTask List Using Element Manager to set the basic parametersReplacing a power supply Task List N0027152 Contents Chapter Viewing the BCM50 system LEDs ContentsChapter Installing the main unit Chapter Configuring the BCM50 system Chapter Connecting the BCM50 system to the LAN and WAN 194 Index Contents N0027152 Canadian Notice Regulatory informationNorth American regulatory information Ringer Equivalence Number REN Federal Communications Commission FCC NoticeEMI/EMC FCC Part Regulatory informationInstallation Important safety instructionsUse of a music source SafetyTelecommunication registration Enhanced 911 configurationRadio-frequency interference International regulatory information Additional safety information ITU standardization compliance Getting started with BCM50 ChapterAbout this guide PurposeOrganization About BCM50BCM50 key elements BCM50 includes the following key elementsBCM50 features Symbols and conventions used in this guide Whichever set you are using Example Use the info commandRelated publications Indicates book titlesCallPilot and Call Center Guides If you do not see an appropriate number in this list, go to How to get helpEuropean Free phone 00800 800 800-4NORTEL Use Express Routing Code ERC 1063#44-191-555-7980 Emeahelp@nortel.comMail Getting started with BCM50 N0027152 Main units Introducing the BCM50 hardwareIntroducing the BCM50 hardware BCM50 main unit ports and connectorsPort/connector Description Expansion unit and media bay modules Expansion unit ports/connectors and descriptionsExpansion unit Main unit Media bay modulesModule type What it does Special notes Trunk MBMsDigital trunk media bay module Station MBMs Sheet 1 Brim faceplateDSM Introducing the BCM50 hardware Station MBMs Sheet 2Analog station media bay modules ATA2 ASM8 ASM8+ Gasm Gasi Rackmount shelf BCM50 hardwareWallmount bracket Patch panelWallmount bracket Wiring field card WFCBCM50 components Power supplyPower supply adapter cord international users Uninterruptable power supply Cooling fan Hard diskCooling fan Analog telephones RJ-21 telephony connectorField-replaceable units Field-replaceable unitsRouter card Introducing the BCM50 hardware Media bay modules Telephones and adaptersIntroducing the BCM50 hardware ABC Accessories Introducing the BCM50 hardware N0027152 Viewing the BCM50 system LEDs Viewing the BCM50 system LEDsSystem status LEDs Power Status Description System status LEDs during startup or rebootLAN port LEDs System status LEDs states and descriptionsStatus Description LAN port LED locationsAdsl router LED descriptions Adsl router LEDs BCM50a onlyDescribes the possible Adsl router LED states Describes the possible Ethernet router LED states LAN port LED indicatorsEthernet router LEDs BCM50e only Describes the possible MBM LED states Media bay module LEDs expansion units onlyFollowing MBMs have additional LEDs MBM LED descriptionsDescribes the functions of the DTM LEDs DTM LEDsDTM LED functions Status DescriptionsBrim LED functions Brim LEDsDescribes the functions of the Brim LEDs Determining Dhcp server configuration and IP address Determining Dhcp server configuration and IP addressBCM50 main unit no integrated router If an external Dhcp server is not presentIf an external Dhcp server is present BCM50a or BCM50e with integrated routerTo disable the Dhcp server on the main unit Page Installing the BCM50 system Installing the BCM50 systemSupplies, and tools on Tasks Description Link toInstalling telephones Installing the BCM50 system N0027152 Checking the installation prerequisites Checking the installation prerequisitesEnvironmental requirements Electrical requirementsDigital loop Site telephony wiring requirementsAnalog loop System equipment, supplies, and toolsBasic hardware Optional equipmentOther hardware and tools Shows the steps required to install the main unit Installing the main unitUnpacking the main unit Installing the BCM50 unit in an equipment rackInstalling the main unit Installing the BCM50 unit on the rackmount shelf To install the rackmount shelf in an equipment rackAttach the units to the rackmount shelf N0027152 To install the BCM50 unit on the rackmount shelfTo install the patch panel optional To install a BCM50 unit on top of another unitTo install the power supply on the rackmount shelf To install the BCM50 wallmount bracket Installing the BCM50 unit on the wallWallmount bracket Wallmount lock in unlock position To install the BCM50 unit on the wallmount bracketAttach the BCM50 unit to the wallmount bracket Repeat for each BCM50 power supply Installing the wiring field card optionalTo install the WFC To install the BCM50 unit on a desktop or shelf Installing the BCM50 unit on a desktop or shelfNext step Installing an expansion unit Installing an expansion unitUnpacking the expansion unit Verifying the media bay module switch settings Gasm dip switch settings switch To set Gasm dip switchesTo set Gatm dip switches To install a media bay module MBM Installing a media bay module in an expansion unitInstalling the expansion unit Installing an expansion unit N0027152 Connecting the cables to the BCM50 system Connecting the cables to the BCM50 systemExpansion unit Connecting the expansion unitTo connect an expansion unit Connecting the expansion unit to the BCM50 Main UnitDefault line and extension numbers Connecting the power supplyDefault Extension numbers Line numbers Expansion portTo connect a power supply without a UPS To connect a power supply using a UPSConnecting the lines and extensions Wiring warnings To connect the lines and extensions Read the warnings in Wiring warnings onTo connect telephone lines to DTM, BRIM, or 4x16 MBMs Connecting telephone lines to the expansion unitsTo connect extensions to DSM16, DSM32, ASM8, or 4x16 MBMs Connecting extensions to the expansion unitsTo connect analog telephone lines to the GATM4 or GATM8 Connecting an auxiliary ringer Connecting the auxiliary equipmentTo install an external paging system To install an auxiliary ringerConnecting an external paging system Tip Paging tips Connecting an external music sourceMusic source jack To connect the music source using the music source jackTo connect the cables to the patch panel optional To connect the cables to the wiring field card optionalNext step Analog terminal adapter Installing telephones and peripheralsSystem telephones To install the emergency telephone Installing an emergency telephoneInstalling telephones and peripherals Central Answering Position CAP/eCAPInstalling T7406 cordless systems Installing IP PhonesInstalling telephones and peripherals N0027152 Configuration overview Installing the analog terminal adapterRefer to on page 45 for ATA2 specifications Analog telephoneConnecting the ATA2 Installing the ATA2This section provides information on installing the ATA2 Installing the analog terminal adapterTo connect the ATA2 Chapter Installing the analog terminal adapterMounting the ATA2 To mount the ATA2 on a wallATA2 back view Mounting keyhole slots Test insertion loss measurementConfiguring the ATA2 Installing the analog terminal adapter N0027152 Configuring the BCM50 system Configuring the BCM50 systemInitial parameters Initial parameters overviewStartup parameters Startup parameters overviewConfiguring the BCM50 system N0027152 Using Telset Administration to set the basic parameters Using Telset Administration to set the basic parametersTo enter the keycodes Configuring the initial parametersTo configure the IP address To select the region To configure the modemTo create Telset user accounts To select the telephony startup template and startDNTo initialize voice mail Next step Page Using Element Manager to set the basic parameters Using Element Manager to set the basic parametersTo connect to the BCM50 system Accessing the BCM50 systemTo download and install Element Manager Attribute Description To configure the IP subsystemModify IP Settings attributes Attribute To configure the start-up template for telephony servicesCold Reset Telephony attributes Click Install Configuring the startup parametersQuick Install Wizard attributes To enter a name for your systemDate and Time attributes To configure the date and time settingsTo configure Dhcp server settings Configure the Dhcp server attributes see Table To configure IP PhonesDhcp server general settings attributes IP Terminal Global Settings attributesTo configure Snmp community strings To configure Snmp settingsModify Snmp Settings attributes Click Add.... The Add Community String dialog box opensConfigure the Add Community String attributes. see Table To configure the Snmp manager listTo create user accounts Click Ok Repeat steps 4 to 6 to add more community stringsClick Ok Repeat steps 4 to 6 to create more user accounts Using the Startup Profile to configure parameters Using the Startup Profile to configure parametersStartup Profile requirements To customize a Startup Profile for your system Configuring basic parametersTo download the Startup Profile template To load the Startup Profile data onto the BCM50 system Next step Using the Startup Profile to configure parameters N0027152 Completing the initial installation optional Completing the initial installation optionalTo configure the MBMs Configuring the media bay moduleConfiguring voice mail Configuring modem settingsChecking for software updates Customizing security policies Performing a backupConnecting the BCM50 system to the LAN and WAN Connecting the BCM50 system to the LAN and WANDescribes the function and use of each of the ports Connecting the BCM50 system to the LANLAN ports on the main unit Sheet 1 Port name FunctionLAN ports on the main unit Sheet 2 To connect the BCM50 system to the LANTo connect the BCM50e main unit to the WAN Connecting the BCM50 system to the WANBCM50a main unit BCM50e main unitProceed to Next step To connect the BCM50a main unit to the WANConnecting the BCM50 system to the LAN and WAN N0027152 To test the main unit Testing basic BCM50 functionalityTesting basic BCM50 functionality To test the expansion unit To test the main unit without a valid keycodeTo troubleshoot the main unit To test a station MBM To troubleshoot the expansion unitTo test the MBM To test a trunk MBM To determine why an MBM does not appear in Element ManagerTo determine why the ATA2 does not function To check the ATA2 wiring Reset to factory settingsTo determine why there is no dial tone at the ATA2 To perform a Level 1 and Level 2 reset Reset levelsActivate the reset feature Set Level 2 reset Testing basic BCM50 functionality Level 1 resetReplacing the BCM50 system components Replacing the BCM50 system componentsReplacing the BCM50 system components N0027152 Replacing a power supply Replacing a power supplyRemoving the power supply Preparing the system for maintenanceTo remove the power supply Check for a recent backup of the BCM50 system programmingReturning the system to operation Connect the new power supplyTo connect the new power supply Replacing a power supply N0027152 Replacing a main unit Replacing a main unitTo disconnect the cables To remove a wallmounted main unit Removing the main unitTo remove a rackmounted main unit To connect the cables Installing the new main unitTo remove a desktop mounted main unit To return the system to operation Replacing a main unit N0027152 Replacing a media bay module Refer to the following procedures to replace an MBMReplacing a media bay module Remove an MBM To remove the MBMTo insert the new MBM Replacing a media bay module N0027152 Replacing an expansion unit Replacing an expansion unitTo disconnect the expansion unit cables Disconnecting the cablesRemoving the expansion unit To remove a desktop-mounted expansion unit To remove a rackmounted expansion unitTo remove a wallmounted expansion unit Inserting the MBM in the new expansion unit Removing the MBMInstalling the new expansion unit Replacing an expansion unit Replacing an internal component Replacing an internal componentSpecial tools Removing the main unit To remove a desktop-mounted main unit Opening the main unit caseTo open the main unit case Ensure that all the cables are removed from the main unitBCM50 case screws Lift the top of the case off of the BCM50 unit Use one of the following procedures to remove the componentRemoving an internal component Hard disk cables To remove the hard diskHard disk and bracket screws To remove the fanFan To remove the router cardTo insert the new hard disk Inserting the new componentInsert screws To insert the new fan Perform a restore or manual reprogram of the systemTo close the main unit case Closing the main unit caseTo insert the new router card Replacing the top of the case Installing the main unitTo return the BCM50 system to operation Replacing an internal component Appendix a RJ-21 telephony connector wiring chartAppendix a RJ-21 telephony connector wiring chart RJ-21 telephony connector wiring Sheet 2 Appendix B LAN ports wiring chart LAN ports wiring chartAppendix B BCM50a BCM50ePin Signal Lists the wiring details for the LAN portsLAN port wiring On page 210 list the wiring details for the WAN ports WAN ports wiring chartAppendix C WAN ports wiring chart RJ-11 WAN port wiringRJ-45 WAN port wiring Lists the wiring details for the expansion ports Expansion ports wiring chartAppendix D Expansion ports wiring chart Expansion port wiring Sheet 1FS256 Receive Data + FS256 Receive Data Appendix E DTM wiring chart DTM wiring chartDefault line numbers on Line type Expansion port Appendix EAppendix E DTM wiring chart N0027152 On page 216 list the wiring details for the RJ-45 ports Brim wiring chartAppendix F Brim wiring chart Brim RJ-45 port wiringDefault line numbers on Port number Expansion port Appendix F Brim wiring chart Brim line numberingAppendix G Gatm wiring chart Gatm wiring chartGATM4 RJ-21 connector wiring Sheet 1 Appendix GGATM8 RJ-21 connector wiring Sheet 1 Ring Slate-Violet Appendix G Gatm wiring chart N0027152 Appendix H 4x16 wiring charts 4x16 wiring charts4x16 RJ-11 port wiring Appendix HAppendix H 4x16 wiring charts 4x16 default line numbering Lists the wiring details for the RJ-21 connector on4x16 RJ-21 connector wiring Sheet 1 Default line number on Port number Expansion portTip Black-Brown Appendix H 4x16 wiring charts N0027152 Appendix I DSM16 and DSM32 wiring charts DSM16 and DSM32 wiring chartsDSM16 and DSM32 RJ-21 connector wiring Sheet 1 Appendix241 Set Pin Connection Wire color RJ-21242 243Lists the wiring details for the RJ-21 connector on the ASM ASM8, ASM8+, and Gasm wiring chartAppendix J ASM8, ASM8+, and Gasm wiring chart ASM RJ-21 connector wiring Sheet 1Expansion port No connection Violet-Slate Slate-Violet Default DN on Set Pin ConnectionSystem region attributes Regional default system valuesAppendix K Default languages by region Regional language default valuesAppendix K System region attributes South/Central America language supportRegional companding law Regional caller ID display formatsRegional media bay module availability Companding law by regionPRI line protocol supported, by region Sheet 1 Regional PRI line protocol supportShows the PRI line protocol support by region Mcdn over PRI SL-1 Isdn line servicesIsdn line services Define time zones by country and language Protocol Region Available Isdn servicesTime/date formats based on language Language/Country Time/Date formatRegion defaults Sheet 1 System defaultsDefault dialing restrictions, by profile Restriction filter defaultsAppendix K System region attributes Region defaults Sheet 2 Provides a description of the types of digital trunk types Digital trunk typesDigital trunk types and descriptions Sheet 1 Digital trunk Description TypesDefault voice mail CallPilot region default languages by countryCallPilot regions Analog trunk typesSpain Sweden Switzerland CallPilot feature default anomaliesAppendix K System region attributes N0027152 Numerics IndexDhcp IndexLED PRI CAP Index N0027152