Chapter Command Line Interface CLI | Nortel Networks R2MFC specs

73

Chapter 7

Command Line Interface (CLI)

Overview

This chapter describes the Command Line Interface (CLI) available through the serial port.

Command Line Interface (CLI) commands are organized as a tree of directories. Each directory contains a set of commands related to a specific purpose or subject. The available directories for R2MFC MBM are:

•LOad

•INfo

•VIew

•CNtrl

•COnfig

•ALarm

•SWerr

•MFC

•R2

•PRI

Note: Most directories and commands have a short form indicated by uppercase letters.

To access a directory, type the directory name or the short form. A list (or menu) of available commands or subdirectories displays. The commands are not case-sensitive.The list displays again if you type an incorrect command or an empty command.

To go to the previous menu level in the tree, type an asterisk (*).

Users and passwords

The CLI contains the following two hard-coded user names with passwords:

•RS232 — This is the default user, which does not require a password. This user accesses configuration and maintenance commands.

•admin — Password: admin. This user has access to the same set of commands as RS232.

Note: Users and passwords are case-sensitive.

R2MFC Media Bay Module Installation and Configuration Guide

Image 73

Nortel Networks R2MFC manual Chapter Command Line Interface CLI, Overview, Users and passwords

Contents

R2MFC Media Bay Module Installation and Configuration Guide North American Regulatory Information Safety R2MFC Media Bay Module Installation and Configuration Guide Enhanced 911 ConfigurationRadio-frequency Interference Hearing Aid Compatibility Important Safety InstructionsRepairs NN40010-300 International Regulatory Information NN40010-300 Contents Chapter Preparing to install the R2MFC MBM Chapter R2MFC MBM maintenance Appendix a Configuring DIP switch settings and definitions MFC Register Signaling Panama Config 1 NN40010-300 Getting Help over the phone from a Nortel Solutions Center How to Get HelpGetting Help from the Nortel Web site Getting Help through a Nortel distributor or reseller How to Get Help NN40010-300 About this guide Getting startedAudience Acronyms Before you begin Symbols and text conventions Convention Example Used for Pswd Related publications Getting started NN40010-300 General information Chapter Overview R2MFC MBM faceplate elements Administration and maintenance toolsOverview System Status LEDs Config DIP switches R2MFC MBM back and underside elements BNC and RJ-48 connectorsRS232 port E1 Status LEDs MBM DIP switches Power connectors Overview NN40010-300 Chapter Preparing to install the R2MFC MBM Host system setup requirements Installation process mapPreparing to install the R2MFC MBM Host system setup requirements Config DIP switches R2MFC MBM setup requirements Customer supplied hardware requirements Overview of the R2MFC MBM installation Chapter Installing the R2MFC MBM Shutting down the system Installing the R2MFC MBMShutting down a BCM 4.0 system Shutting down the BCM 4.0 system hardware Shutting down a BCM 3.7 or lower system Installing an R2MFC MBM in the BCM platform base chassis Installing an R2MFC MBM Installing an R2MFC MBM in the expansion unit Installing the rubber boot in an R2MFC module Installing an R2MFC MBM in the BCM50 expansion unit R2MFC Transmit Co-axial cable connected to the MBM Removing an R2MFC MBM Reconnecting the equipment Removing an R2MFC MBM from the BCM platform base chassis How to remove a BCM200 R2MFC MBM Removing an R2MFC MBM from the expansion unit How to remove a BCM400 R2MFC MBM How to remove the expansion unit front bezel Wiring an R2MFC MBM Installing the R2MFC MBM Trunk wiring overview Connecting an R2MFC MBM to a service provider Installing the R2MFC MBM Configuring the R2MFC MBM Chapter Configuring the R2MFC MBM Physical line characteristics MFCR2 side External Link configurable parametersE1 framing Register signaling Line signaling Option Parameters Meaning Default Minimum or fixed number length + timer parameters Setting Config DIP switches Configuring the MFCR2 external link Creating a customized country code Config DIP switch layout E1 framing default parameters PRI side Internal Link configurable parameters Signaling Configuring the PRI internal linkConfiguring the PRI internal link using Element Manager Layer 2 signaling parameters Parameter Setting Module configuration parameters BCM lines configuration for R2MFC MBM Configuring the PRI internal link using Unified Manager Module type BCM module configuration for R2MFC MBM Off Turning on second dial tone Turning on second dial tone using Element Manager Outgoing dialing configuration for second dial tone Turning on second dial tone using Unified Manager Configuring the R2MFC MBM Inter-working functionality Chapter R2MFC MBM maintenance Clock synchronization R2MFC MBM maintenanceTranslation of Subscriber Status Setting the R2MFC MBM to diagnostic mode Diagnostic toolsDiagnostic and loopback modes Mode Description Call Availability Alarms Measurements Alarms Incoming signal errors Alarms propagationGroup I Alarms propagation Sheet 1 Alarm Cause Group II alarms propagation R2MFC MBM maintenance Group I Alarms propagation Sheet 2Faceplate LEDs System status monitor LEDs Logs and traces Error messagesLED Name Yellow LED Red LED Replacing an R2MFC MBM Overview of module replacement process Upgrading firmware Connect using Hyper-terminal setup parameters Program responds starting rec 0. Hit any key to continue R2MFC MBM maintenance NN40010-300 Users and passwords Chapter Command Line Interface CLIOverview Command Line Interface CLI Accessing the CLI LOad directory CLI commands CommandsINfo directory CLI commands LOad directory VIew directory VIew directory CLI commands CNtrl directory CNtrl directory CLI commands Sheet 1 NN40010-300 CNtrl directory CLI commands Sheet 3 COnfig directoryCOnfig directory CLI commands Sheet 1 NN40010-300 ALarm directory CLI commands Sheet 1 ALarm directory NN40010-300 SWerr directory SWerr directory CLI commands MFC directory MFC directory CLI commands Sheet 1 MFC directory CLI commands Sheet 2 See Chapter , MFC Signal Definitions, on page 111 for MFC R2 directory R2 directory CLI commands Sheet 1 Command Line Interface CLI R2 directory CLI commands Sheet 2 PRI directory PRI directory CLI commands Command Line Interface CLI NN40010-300 Shows the Config DIP switch layout Appendix a Configuring DIP switch settings and definitions Second dial tone DIP switch settings Country selection DIP switch settings Mexico Config Country code defaultsMexico Config 1 R2 A/B signals Interpretation of transmitted MFC signals Sheet 1 Interpretation of received MFC signalsMeaning Signal Mexico Config Interpretation of received MFC signals Sheet 1 Mexico Config 2 R2 A/B signals Interpretation of transmitted MFC signals Brazil Config 1 R2 A/B signals Brazil Config Interpretation of received MFC signals Brazil Config Brazil Config 2 R2 A/B signals Argentina Config Argentina Config 1 R2 A/B Signals Interpretation of received MFC signals Chile Config 1 R2 A/B signals Chile Config Signal Block Panama Config Configuring DIP switch settings and definitions NN40010-300 Diagnostics and Loopback Dip Switch Settings Appendix B Diagnostic and loopback DIP switch settings Diagnostic and loopback DIP switch settings NN40010-300 MFC signal definitions Appendix C MFC Signal DefinitionsMFC signal meaning MFC Signal Definitions NN40010-300 Cable pinouts Appendix D CLI Cable Pinout CLI Cable Pinout NN40010-300