Mexico Config 2 R2 A/B signals | Nortel Networks R2MFC instruction

96Configuring DIP switch settings and definitions

R2 line signaling

Mexico Config 2 R2 signals are according to CCITT standard. See Table 31 for the Mexico Config 2 R2 signal definitions.

Table 31 Mexico Config 2 R2 A/B signals

Forward				Backward

Signal	A	B		Signal	A	B


Idle	1	0		Idle	1	0

Seize	0	0		Seize acknowledge	1	1

Clear forward	1	0		Answer	0	1

				Clear back	1	1

				Block	1	1

Note: CD bits are not used. They are set to 01 in transmit direction, and are ignored in receive direction.

MFC register signaling

MFC signal definitions depends on the stage and the direction of the call; there are four tables of 15 signals each: the first stage uses I signals forward and A signals backward, and the second stage uses II signals forward and B signals backward. The meaning of the signals can also be different when being transmitted or received. Meanings of the MFC signals are configurable. MFC signal tables are part of the country-specific parameters.

Table 32 shows the MFC signal configuration in the R2MFC MBM accessed through the CLI for Mexico Config 2. Table 33 on page 97 shows the MFC transmitted signal configuration in the R2MFC MBM accessed through the CLI for Mexico Config 2. These values are preconfigured by the faceplate DIP switches as shown in Figure 30 on page 92. See Chapter 7, “Command Line Interface (CLI),” on page 73 for information on the CLI.

Table 32 Interpretation of received MFC signals (Sheet 1 of 2)

Meaning	Signal	Meaning	Signal	Meaning	Signal	Meaning	Signal

FW_Digit_1	I_1	FW_Categ_1	II_1	BW_NextDig	A_1	BW_FreeCharge	B_1

FW_Digit_2	I_2	FW_Categ_2	II_2	BW_PrevDigit	A_2	BW_Busy	B_2

FW_Digit_3	I_3	FW_Categ_3	II_3	BW_BCateg	A_3	BW_B_Congest	B_3

FW_Digit_4	I_4	FW_Categ_4	II_4	BW_A_Congest	A_4	BW_B_Congest	B_4

FW_Digit_5	I_5	FW_Categ_5	II_5	BW_Category	A_5	BW_Unlocated	B_5

FW_Digit_6	I_6	FW_Categ_6	II_6	BW_SpeechChrg	A_6	BW_B_Congest	B_6

FW_Digit_7	I_7	FW_Categ_7	II_7	BW_Prev2Digit	A_7	BW_B_Congest	B_7

NN40010-300

Image 96

Nortel Networks R2MFC manual Mexico Config 2 R2 A/B signals, Interpretation of received MFC signals Sheet 1

Contents

R2MFC Media Bay Module Installation and Configuration Guide Safety North American Regulatory Information Enhanced 911 Configuration R2MFC Media Bay Module Installation and Configuration GuideRadio-frequency Interference Important Safety Instructions Hearing Aid CompatibilityRepairs NN40010-300 International Regulatory Information NN40010-300 Contents Chapter Preparing to install the R2MFC MBM Chapter R2MFC MBM maintenance Appendix a Configuring DIP switch settings and definitions MFC Register Signaling Panama Config 1 NN40010-300 How to Get Help Getting Help over the phone from a Nortel Solutions CenterGetting Help from the Nortel Web site Getting Help through a Nortel distributor or reseller How to Get Help NN40010-300 Getting started About this guideAudience Before you begin Acronyms Symbols and text conventions Pswd Convention Example Used for Related publications Getting started NN40010-300 Chapter Overview General information Administration and maintenance tools R2MFC MBM faceplate elementsOverview Config DIP switches System Status LEDs BNC and RJ-48 connectors R2MFC MBM back and underside elementsRS232 port E1 Status LEDs Power connectors MBM DIP switches Overview NN40010-300 Chapter Preparing to install the R2MFC MBM Installation process map Host system setup requirementsPreparing to install the R2MFC MBM Host system setup requirements R2MFC MBM setup requirements Config DIP switches Customer supplied hardware requirements Chapter Installing the R2MFC MBM Overview of the R2MFC MBM installation Installing the R2MFC MBM Shutting down the systemShutting down a BCM 4.0 system Shutting down a BCM 3.7 or lower system Shutting down the BCM 4.0 system hardware Installing an R2MFC MBM Installing an R2MFC MBM in the BCM platform base chassis Installing an R2MFC MBM in the expansion unit Installing an R2MFC MBM in the BCM50 expansion unit Installing the rubber boot in an R2MFC module R2MFC Transmit Co-axial cable connected to the MBM Reconnecting the equipment Removing an R2MFC MBM How to remove a BCM200 R2MFC MBM Removing an R2MFC MBM from the BCM platform base chassis How to remove a BCM400 R2MFC MBM Removing an R2MFC MBM from the expansion unit Wiring an R2MFC MBM How to remove the expansion unit front bezel Installing the R2MFC MBM Connecting an R2MFC MBM to a service provider Trunk wiring overview Installing the R2MFC MBM Chapter Configuring the R2MFC MBM Configuring the R2MFC MBM MFCR2 side External Link configurable parameters Physical line characteristicsE1 framing Line signaling Register signaling Minimum or fixed number length + timer parameters Option Parameters Meaning Default Configuring the MFCR2 external link Setting Config DIP switches Config DIP switch layout Creating a customized country code PRI side Internal Link configurable parameters E1 framing default parameters Configuring the PRI internal link SignalingConfiguring the PRI internal link using Element Manager Layer 2 signaling parameters Module configuration parameters Parameter Setting Configuring the PRI internal link using Unified Manager BCM lines configuration for R2MFC MBM Module type BCM module configuration for R2MFC MBM Off Turning on second dial tone using Element Manager Turning on second dial tone Turning on second dial tone using Unified Manager Outgoing dialing configuration for second dial tone Configuring the R2MFC MBM Chapter R2MFC MBM maintenance Inter-working functionality R2MFC MBM maintenance Clock synchronizationTranslation of Subscriber Status Diagnostic tools Setting the R2MFC MBM to diagnostic modeDiagnostic and loopback modes Mode Description Call Availability Alarms Alarms Measurements Alarms propagation Incoming signal errorsGroup I Alarms propagation Sheet 1 Alarm Cause R2MFC MBM maintenance Group I Alarms propagation Sheet 2 Group II alarms propagationFaceplate LEDs System status monitor LEDs Error messages Logs and tracesLED Name Yellow LED Red LED Overview of module replacement process Replacing an R2MFC MBM Upgrading firmware Hyper-terminal setup parameters Connect using Program responds starting rec 0. Hit any key to continue R2MFC MBM maintenance NN40010-300 Chapter Command Line Interface CLI Users and passwordsOverview Accessing the CLI Command Line Interface CLI Commands LOad directory CLI commandsINfo directory CLI commands LOad directory VIew directory CLI commands VIew directory CNtrl directory CLI commands Sheet 1 CNtrl directory NN40010-300 COnfig directory CNtrl directory CLI commands Sheet 3COnfig directory CLI commands Sheet 1 NN40010-300 ALarm directory ALarm directory CLI commands Sheet 1 NN40010-300 SWerr directory CLI commands SWerr directory MFC directory CLI commands Sheet 1 MFC directory MFC directory CLI commands Sheet 2 See Chapter , MFC Signal Definitions, on page 111 for MFC R2 directory CLI commands Sheet 1 R2 directory Command Line Interface CLI R2 directory CLI commands Sheet 2 PRI directory CLI commands PRI directory Command Line Interface CLI NN40010-300 Appendix a Configuring DIP switch settings and definitions Shows the Config DIP switch layout Country selection DIP switch settings Second dial tone DIP switch settings Country code defaults Mexico ConfigMexico Config 1 R2 A/B signals Interpretation of received MFC signals Interpretation of transmitted MFC signals Sheet 1Meaning Signal Mexico Config Mexico Config 2 R2 A/B signals Interpretation of received MFC signals Sheet 1 Interpretation of transmitted MFC signals Brazil Config Brazil Config 1 R2 A/B signals Interpretation of received MFC signals Brazil Config Brazil Config 2 R2 A/B signals Argentina Config Argentina Config 1 R2 A/B Signals Interpretation of received MFC signals Chile Config Chile Config 1 R2 A/B signals Signal Block Panama Config Configuring DIP switch settings and definitions NN40010-300 Appendix B Diagnostic and loopback DIP switch settings Diagnostics and Loopback Dip Switch Settings Diagnostic and loopback DIP switch settings NN40010-300 Appendix C MFC Signal Definitions MFC signal definitionsMFC signal meaning MFC Signal Definitions NN40010-300 Appendix D CLI Cable Pinout Cable pinouts CLI Cable Pinout NN40010-300