NN40010-300 | Nortel Networks R2MFC specification

82 Chapter 7 Command Line Interface (CLI)

Table 23 ALarm directory CLI commands (Sheet 2 of 2)

CLI command	Description

GRDtime <link_no> <grs_state>	Changes group 1 alarm guard time for the required grade of service state.
<grd_time>
	Where:
	link_no is the PCM link number, 0 or 1.
	grs_state is the grade of service state, 1 (mnt state) or 2 (oos state).
	grd_time is the guard time in the range of 20...50000.

G2Gtime <link_no> <grd_time>	Changes the group 2 alarm guard time for the required grade of service
	state.
	Where:
	link_no is the PCM link number, 0 or 1.
	grd_time is the group guard time in the range of 0...50000.

G2Ptime <link_no> <perstime>	Changes persistence time for group 2 alarm handling.
	Where:
	link_no is the PCM link number, 0 or 1.
	perstime is the persistence time for group 2 alarm handling in the range of
	0...50000.

DB <link_no>	Displays the R2MFC MBM alarm task database content.
	Where:
	link_no is the PCM link number, 0 or 1.

NN40010-300

Image 82

Nortel Networks R2MFC manual NN40010-300

Contents

R2MFC Media Bay Module Installation and Configuration Guide Safety North American Regulatory Information R2MFC Media Bay Module Installation and Configuration Guide Enhanced 911 ConfigurationRadio-frequency Interference Repairs Important Safety InstructionsHearing Aid Compatibility NN40010-300 International Regulatory Information NN40010-300 Contents Chapter Preparing to install the R2MFC MBM Chapter R2MFC MBM maintenance Appendix a Configuring DIP switch settings and definitions MFC Register Signaling Panama Config 1 NN40010-300 Getting Help from the Nortel Web site How to Get HelpGetting Help over the phone from a Nortel Solutions Center Getting Help through a Nortel distributor or reseller How to Get Help NN40010-300 About this guide Getting startedAudience Before you begin Acronyms Symbols and text conventions Pswd Convention Example Used for Related publications Getting started NN40010-300 Chapter Overview General information R2MFC MBM faceplate elements Administration and maintenance toolsOverview Config DIP switches System Status LEDs RS232 port BNC and RJ-48 connectorsR2MFC MBM back and underside elements E1 Status LEDs Power connectors MBM DIP switches Overview NN40010-300 Chapter Preparing to install the R2MFC MBM Preparing to install the R2MFC MBM Installation process mapHost system setup requirements Host system setup requirements R2MFC MBM setup requirements Config DIP switches Customer supplied hardware requirements Chapter Installing the R2MFC MBM Overview of the R2MFC MBM installation Shutting down the system Installing the R2MFC MBMShutting down a BCM 4.0 system Shutting down a BCM 3.7 or lower system Shutting down the BCM 4.0 system hardware Installing an R2MFC MBM Installing an R2MFC MBM in the BCM platform base chassis Installing an R2MFC MBM in the expansion unit Installing an R2MFC MBM in the BCM50 expansion unit Installing the rubber boot in an R2MFC module R2MFC Transmit Co-axial cable connected to the MBM Reconnecting the equipment Removing an R2MFC MBM How to remove a BCM200 R2MFC MBM Removing an R2MFC MBM from the BCM platform base chassis How to remove a BCM400 R2MFC MBM Removing an R2MFC MBM from the expansion unit Wiring an R2MFC MBM How to remove the expansion unit front bezel Installing the R2MFC MBM Connecting an R2MFC MBM to a service provider Trunk wiring overview Installing the R2MFC MBM Chapter Configuring the R2MFC MBM Configuring the R2MFC MBM Physical line characteristics MFCR2 side External Link configurable parametersE1 framing Line signaling Register signaling Minimum or fixed number length + timer parameters Option Parameters Meaning Default Configuring the MFCR2 external link Setting Config DIP switches Config DIP switch layout Creating a customized country code PRI side Internal Link configurable parameters E1 framing default parameters Configuring the PRI internal link using Element Manager Configuring the PRI internal linkSignaling Layer 2 signaling parameters Module configuration parameters Parameter Setting Configuring the PRI internal link using Unified Manager BCM lines configuration for R2MFC MBM Module type BCM module configuration for R2MFC MBM Off Turning on second dial tone using Element Manager Turning on second dial tone Turning on second dial tone using Unified Manager Outgoing dialing configuration for second dial tone Configuring the R2MFC MBM Chapter R2MFC MBM maintenance Inter-working functionality Clock synchronization R2MFC MBM maintenanceTranslation of Subscriber Status Diagnostic and loopback modes Diagnostic toolsSetting the R2MFC MBM to diagnostic mode Mode Description Call Availability Alarms Alarms Measurements Group I Alarms propagation Sheet 1 Alarms propagationIncoming signal errors Alarm Cause Faceplate LEDs R2MFC MBM maintenance Group I Alarms propagation Sheet 2Group II alarms propagation System status monitor LEDs LED Name Yellow LED Error messagesLogs and traces Red LED Overview of module replacement process Replacing an R2MFC MBM Upgrading firmware Hyper-terminal setup parameters Connect using Program responds starting rec 0. Hit any key to continue R2MFC MBM maintenance NN40010-300 Users and passwords Chapter Command Line Interface CLIOverview Accessing the CLI Command Line Interface CLI INfo directory CLI commands CommandsLOad directory CLI commands LOad directory VIew directory CLI commands VIew directory CNtrl directory CLI commands Sheet 1 CNtrl directory NN40010-300 CNtrl directory CLI commands Sheet 3 COnfig directoryCOnfig directory CLI commands Sheet 1 NN40010-300 ALarm directory ALarm directory CLI commands Sheet 1 NN40010-300 SWerr directory CLI commands SWerr directory MFC directory CLI commands Sheet 1 MFC directory MFC directory CLI commands Sheet 2 See Chapter , MFC Signal Definitions, on page 111 for MFC R2 directory CLI commands Sheet 1 R2 directory Command Line Interface CLI R2 directory CLI commands Sheet 2 PRI directory CLI commands PRI directory Command Line Interface CLI NN40010-300 Appendix a Configuring DIP switch settings and definitions Shows the Config DIP switch layout Country selection DIP switch settings Second dial tone DIP switch settings Mexico Config Country code defaultsMexico Config 1 R2 A/B signals Interpretation of transmitted MFC signals Sheet 1 Interpretation of received MFC signalsMeaning Signal Mexico Config Mexico Config 2 R2 A/B signals Interpretation of received MFC signals Sheet 1 Interpretation of transmitted MFC signals Brazil Config Brazil Config 1 R2 A/B signals Interpretation of received MFC signals Brazil Config Brazil Config 2 R2 A/B signals Argentina Config Argentina Config 1 R2 A/B Signals Interpretation of received MFC signals Chile Config Chile Config 1 R2 A/B signals Signal Block Panama Config Configuring DIP switch settings and definitions NN40010-300 Appendix B Diagnostic and loopback DIP switch settings Diagnostics and Loopback Dip Switch Settings Diagnostic and loopback DIP switch settings NN40010-300 MFC signal definitions Appendix C MFC Signal DefinitionsMFC signal meaning MFC Signal Definitions NN40010-300 Appendix D CLI Cable Pinout Cable pinouts CLI Cable Pinout NN40010-300