Onkyo TX-SA705 Connecting the AV Receiver/AV Amplifier—Continued, Connecting Onkyo Components

Connecting the AV Receiver/AV Amplifier—Continued

Connecting Onkyo Components

IN

L

Step 1: Make sure that each Onkyo component is			R
			CD
connected to the AV receiver/AV amplifier
with an analog audio cable (connection a			FRONT
in the hookup examples) (see pages 29 to		REMOTE	L
		CONTROL
40).			R
Step 2: Make the	connection.		DVD
Step 3: If you’re using an MD, CDR, or RI Dock,			e.g., CD player
change the input display (see page 50).

									R	L
With		(Remote Interactive), you can use the follow-							ANALOG
									AUDIO OUT
ing special functions:									e.g., DVD player
■ Auto Power On/Standby									R	L
	When you start playback on a component connected								ANALOG
									AUDIO OUT
	via	, if the AV receiver/AV amplifier is on
	Standby, it will automatically turn on and select that								Connecting the RS232 Port
	component as the input source. Similarly, when the								This port is for connecting the AV receiver/AV amplifier
	AV receiver/AV amplifier is set to Standby, all com-
									to home automation equipment and external controllers.
	ponents connected via				will also go on Standby.
■ Direct Change									Connecting the Power Cord
	When playback is started on a component connected								Notes:
	via	, the AV receiver/AV amplifier automatically
									• Before connecting the power cord, connect all of
	selects that component as the input source. If your
									your speakers and AV components.
	DVD player is connected to the AV receiver/AV
									• Turning on the AV receiver/AV amplifier may cause a
	amplifier’s multichannel DVD input, you’ll need to
									momentary power surge that might interfere with
	press the [MULTI CH] button to hear all channels
									other electrical equipment on the same circuit. If this
	(see page 60), as the Direct Change						function
									is a problem, plug the AV receiver/AV amplifier into a
	only selects the DVD FRONT L/R jacks.
									different branch circuit.
■ Remote Control									• Do not use a power cord other than the one supplied
									with the AV receiver/AV amplifier. The supplied
	You can use the AV receiver/AV amplifier’s remote
									power cord is designed exclusively for use with the
	controller to control your other					-capable Onkyo
									AV receiver/AV amplifier and should not be used with
	components, pointing the remote controller at the
									any other equipment.
	AV receiver/AV amplifier’s remote control sensor								• Never disconnect the power cord from the AV
	instead of the component. You must enter the appro-								receiver/AV amplifier while the other end is still
	priate remote control code first (see page 105).								plugged into a wall outlet. Doing so may cause an
									electric shock. Always disconnect the power cord
Notes:									from the wall outlet first, and then the AV receiver/AV
									amplifier.
•	Use only		cables for		connections.			cables
									Step 1 (not North American model):
	are supplied with Onkyo players (DVD, CD, etc.).
•	Some components have two					jacks. You can con-			Connect the supplied power cord to the AV
									receiver/AV amplifier’s AC INLET.
	nect either one to the AV receiver/AV amplifier. The
	other jack is for connecting additional							-capable
	components.
•	Connect only Onkyo components to						jacks. Con-
	necting other manufacturer’s components may cause a
	malfunction.
•	Some components may not support all							functions.	To AC wall outlet
	Refer to the manuals supplied with your other Onkyo
	components.								Step 2: Plug the power cord into an AC wall outlet.
•	While Zone 2 is on, the Auto Power On/Standby and
									(The Standby indicator lights up.)
	Direct Change			functions do not work.

43