Panasonic AJ-HD1800P <DIF, (continued)

Setup menus (continued)

<DIF>

No./Item		Description of setting
880*1	For setting the transfer speed of the IEEE1394
	digital interface output.
DIF SPEED	0000	S100
	100Mbps
	0001	S200
	200Mbps
	0002	S400
	400Mbps
	<Note>
	When S100 has been selected as this item’s setting,
	DVCPRO HD format signals cannot be input or
	output.
882*1	For setting the input channel.
DIF IN CH	0000	0
	:	:
	0063	63
	The input channel is fixed at the channel
	corresponding to the number specified.
	0064	AUTO
	The input channel is not fixed at the channel
	corresponding to the number specified. The input
	channel is initialized to 63 when the power is
	turned on.
883*1	For setting the output channel.
DIF OUT CH	0000	0
	:	:
	0063	63
	The input channel is fixed at the channel
	corresponding to the number specified.
	0064	AUTO
	The output channel is not fixed at the channel
	corresponding to the number specified. The output
	channel is initialized to 63 when the power is
	turned on.
886*1	Menu item for expansion purposes. Normally,
	use DFLT as the setting.
DIF CONFIG	0000	DFLT
	0001	1
	:	:
	0255	255
890*1	For setting the audio channels to which the
	signals from the IEEE1394 digital interface are to
DIF AUD	be output in the DV format when a DVCPRO HD
	tape or 50M format tape is played back or when a
OUT
	DV tape in 4ch mode is played by the audio
	signals and menu No. 891 DIF DV AUDIO is set to
	“LOCK48.”
	0000	CH1/2
	CH1 and CH2
	0001	CH3/4
	CH3 and CH4
891*1	For setting forcible audio mode conversion when a
	DV tape is played back and the audio signals are
DIF DV	output in the DV format.
AUDIO	0000	THRU
	Normal setting (the signals simply pass through).
	0001	LOCK
	Forcible conversion to the LOCK mode (no
	frequency conversion)
	0002	LOCK48

Forcible conversion to 48kHz/2CH/LOCK.

*1 When the 23/24 Hz mode, 25 Hz (HD, SD) mode, or the 50 Hz (HD, SD) mode is selected in System Menu No. 25 (SYSTEM FREQ), this item is not displayed.

No./Item		Description of setting
892*1	For setting how to reply when signals requesting
	a confirmation of the format is sent from an
DIF SIG CMD	external device connected by the IEEE1394
	digital interface.
	0000	50M
	DVDPRO50 is forcibly returned.
	0001	25M
	DVDPRO is forcibly returned.
	0002	DV
	DV is forcibly returned.
	0003	AUTO
	The reply is the same format as the signal format
	output from the IEEE1394 digital interface.
	<Note>
	When the unit is connected to a non-linear editing
	system using 50M, 25M, and DV signal format, the
	non-linear editing system may not operate properly.
	In this case, change the setting to return format
	information corresponding to the connected signal
	format in this menu and then start the system.
894*1	For setting the format of the signals to be output
	from the IEEE1394 digital interface in the EE
HD >DIF	mode, in recording or when a DVCPRO HD tape is
	played back.
OUT
	0000	HD
	DVCPRO HD
	0001	50M
	DVCPRO50
	0002	DV
	DV
	<Note>
	When SD SDI is selected in Setup menu No. 600
	(VIDEO IN SEL) and cross-conversion is provided,
	data will be output in the format selected in Setup
	menu No. 020 (SYS FORMAT) regardless of this
	menu selection.
895*1	For setting the format of the signals to be output
	from the IEEE1394 digital interface when a 50M
50M > DIF	format tape is played back.
	0000	50M
OUT
	DVCPRO50
	0001	DV
	DV
	<Note>
	When DV is selected as this item’s setting, the closed
	caption signals and time code (VITC) signals in the
	vertical blanking period are transmitted, but none of
	the other signals in the vertical blanking period are
	transmitted.
896*1	For setting the format of the signals to be output
	from the IEEE1394 digital interface when a 25M
25M > DIF	format tape is played back.
	0000	25M
OUT
	DVCPRO
	0001	DV
	DV
899*1	For setting whether the superimposed display is
	to be output from the IEEE1394 digital interface
DIF SUPER	when the format is converted (from HD to 50M,
	from HD to DV, from 50M to DV or from 25M to
	DV).
	0000	OFF
	The superimposed text is not displayed.
	0001	ON
	The superimposed text is displayed.
	<Note>
	Only TCR is displayed.

The underlining (__) denotes the factory setting mode.

110