64
4. Select a desired function by performing one of the fol-
lowing.
•Rotate the JogDial clockwise or counterclockwise.
•Press the + or – button.
•Enter the function number with the numeric buttons.
The function setting will appear on the LCD.
The following diagram describes the function settings
changeable and their factory defaults.
Function Table 2 Table 3
01 MENU D D
02 F1 – F4 E E
03 F5 – F8 E E
04 A B E E
05 TOP SW E E
06 JOYSTICK E E
07 FOCUS NEAR/FAR
EE
08 IRIS OPEN/CLOSE
ED
09 CAM/SET E E
10 MON/ESC E E
11 UNIT E E
12 RECORDER E E
13 CAM POSI E E
14 PRESET E E
15 PGM PRESET D D
16 HISTORY E E
17 –/+ E E
18 JOG DIAL E E
19 SHUTTLE RING
EE
20 SHUTTLE HOLD
EE
21 PLAY/PAUSE E E
22 STOP E E
23 REC E D
24 ALM SUSPEND
ED
25 ALM RESET E E
26 OSD E E
27 ALM RECALL E E
28 SEQ PAUSE E E
29 SEQUENCE E E
30 MULTI SCREEN
EE
31 EL-ZOOM E E
32 AUX1 ON/OFFE E
33 AUX2 ON/OFFE E
34 DEF ON/OFF E E
35 WIPER ON E E
36 SYS FUNC D D
37 CAM FUNC D D
38 GO TO LAST E E
39 MARK E E
40 SEARCH E E
41 T&D SEARCH E E
E=Enabled, D=Disabled
5. Rotate the shuttle ring clockwise or move the 3D joy-
stick to the right. The cursor will jump to the next item.
Note: To return to Step 4, rotate the shuttle ring coun-
terclockwise or move the 3D joystick to the left.
6. Select E or D by performing either of the following.
•Rotate the JogDial clockwise or counterclockwise.
•Press the + or – button.
Note: To change the settings of other functions, repeat
Step 4 to 6.
7. Press the ENTER or CAM (SET) button.
“Set OK?” will appear on the LCD.
Note: To cancel the setting, press the EXIT or MON
(ESC) button. The LCD display will return to Step 6.
8. Press the ENTER or CAM (SET) button again.
The function levels will be set for the selected table.
“Memory” will appear on the LCD for a few seconds,
and the LCD display will return to Step 1.
●Camera Level Setting
You can change the camera levels for each operator. The
camera levels range between Table No. 1 (highest level)
and 3 (Lowest level).
Notes:
•Table No. 1 is fixed to E (Enabled) for all cameras.
•As the factory default, Table No. 2 and 3 are set to
E for all cameras.
1. Display “Camera Level” sub menu. (Refer to Step 1 to 4
of p. 51 To Recall Menu Functions.)
2. Select a desired table (= camera level) by performing
one of the following.
•Rotate the JogDial clockwise or counterclockwise.
•Press the + or – button.
•Enter the function number with the numeric buttons.
3. Press the CAM (SET) button.
The setting menu for the selected table will appear on
the LCD.
Function Table2 405

08 IRIS OPEN/CLOSE=E Camera Level 406

Table No. =3

Camera Level 406

Table No. =1

Function Table2 405

08 IRIS OPEN/CLOSE=D

Function Table2 405

Set OK?

Function Table2 405

Memory

Function Table2 405

08 IRIS OPEN/CLOSE=E