INSERTER

Loading paper

When loading paper in the inserter, load the paper face up. If the paper has a top edge and bottom edge, load in the same top-bottom orientation as the original. Adjust the paper guide on the paper tray to the width of the paper. When using tabbed paper, place the paper as follows:

Load the paper back side up.

The top side is inserted first.

Back side

The relation of copies and tabbed sheets is shown below.

Load tabbed paper

 

 

 

 

 

 

 

 

 

 

 

Copy

 

 

 

Back

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Back

 

 

 

 

 

 

 

Back

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

side

Inserted first.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

side

 

 

 

 

 

 

 

side

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1st sheet

 

 

 

 

 

 

 

1st sheet 2nd sheet 3rd sheet 4th sheet

5th sheet

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4th sheet

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5th sheet

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Back

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Copy result

 

 

 

 

 

 

side

 

Tabbed paper 4th sheet (back side)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Tabbed paper 1st sheet (back side)

Manual operation of the inserter

The inserter can be used for stapling or punching without performing a copy operation. These functions are selected at the operation panel of the inserter.

1 [PUNCH] key

3 [START] key/indicator

When a punch module is installed on the finisher or saddle stitch finisher, punch holes can be added to blank paper or printed paper. The indicator lights when this function is selected.

2[STAPLE] key/indicator

After selecting punch or staple settings with key

1or key 2 , place the paper to be punched or stapled on the inserter tray and press this key.

When this function is selected, each set of output is stapled and delivered to the finisher or saddle stitch finisher tray. (Note that the sets are not offset.) Press this key until the icon light of the desired staple position lights up. (" " pamphlet stapling can only be selected when a saddle stitch finisher is installed)

NOTES

●Do not use tabbed paper when operating the inserter manually.

●The punching and stapling functions cannot be used when the finisher or saddle stitch finisher has failed, or when the functions are prohibited* in the key operator programs (page 11 of the key operator's guide).

*Disabling of stapler/Disabling of punch/Disabling of finisher/Disabling of inserter

3-15