INSERTER

■Alarm display

If the [START] key indicator on the inserter operation panel is blinking and the [PUNCH] key or [STAPLE] key indicator is also blinking or solidly lit, operation will not start when the [START] key is pressed. Resolve the problem as indicated below, depending how the indicators are lit or blinking.

[PUNCH]

 

[STAPLE] indicator

[START]

 

 

 

indicator

 

indicator

 

 

 

 

 

 

 

 

 

Cause

Solution

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A paper size that cannot

Use paper that is a suitable

Any one of the indicators is solidly lit.

Blinks red

 

be fed has been loaded.

size for punching, stapling, or

 

 

 

 

 

 

 

 

 

 

saddle stitching (page 3-3).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Solidly

 

 

 

The paper type of the

Heavy paper cannot be

-

-

 

-

-

Blinks red

 

inserter is set to heavy

used.

 

lit

 

 

 

 

 

 

 

 

 

paper.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The finisher or saddle

Remove the paper from

 

 

 

 

 

 

 

 

 

stitch finisher tray is full.

the tray.

 

 

 

 

 

 

 

 

 

 

 

Blinking

-

 

-

-

-

Blinks red

 

The hole punch scrap

Discard the hole punch

 

 

container in the punch

scrap (page 3-10).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

module on the finisher or

 

 

 

 

 

 

 

 

 

 

saddle stitch finisher is full.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The finisher or saddle

Remove the paper from

 

Any one of the

 

 

 

 

 

stitch finisher tray is full.

the tray.

-

 

-

Blinks red

 

 

 

 

 

The finisher or saddle

Replace the staple

indicators is blinking.

 

 

 

 

 

 

stitch finisher is out of

cartridge (page 3-7).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

staples.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The saddle stitch tray on

Remove the paper from

 

 

 

 

 

 

 

 

 

the saddle stitch finisher is

the saddle stitch tray.

-

-

 

-

-

Blinking

Blinks red

 

full.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The saddle stitch finisher is

Replace the saddle stitch

 

 

 

 

 

 

 

 

 

out of saddle stitch staples.

staple cartridge (page 3-8).

 

 

 

 

 

 

 

 

 

 

 

■Using the inserter

For paper sizes that can be stapled or punched, see the finisher and saddle stitch finisher specifications on page 3-2.

Some paper types cannot be stapled or punched (see "NOTES" on page 3-3). Do not use these paper types.

1 Load paper in the inserter.

NOTE

Paper guide

Load the paper face up.

When performing pamphlet stapling, place the paper so that the opened pages are face up as shown.

Adjust the paper guide to the size of the paper.

Pamphlet stapling can only be used when the saddle stitch finisher (AR-F16) is installed.

When using pamphlet stapling, stapling and punching cannot be used in combination.

3 Press the [START] key.

Make sure that the [START] key light is

2 Press the desired mode key.

Press key 2 on page 3-15for stapling or pamphlet stapling. Press key 1 on page 3-15for punching. The selected mode lights up.

illuminated green and then press the [START] key.

3-16