&F1 |
| Select |
|
| defaults |
&F2 |
| Select synchronous mode factory |
|
| defaults |
&G0 | ■ | Do not generate guard tones |
&G1 |
| Generate guard tones of 550Hz |
&G2 |
| Generate guard tones of 1800Hz |
&H0 ■ | Clock always present in | |
|
| synchronous mode |
&H1 |
| Clock only appears after |
|
| connection |
&K0 |
| Flow control disabled |
&K3 ■ | RTS/CTS (hardware) flow control | |
&K4 |
| XON/XOFF (software) flow control |
&K5 |
| Transparent XON/XOFF flow |
|
| control |
&K9 |
| Failsafe flow control |
&L0 | ■ | PSTN mode |
&L1 |
| |
&L2 |
| Auto leased line Originate mode |
&L3 |
| Auto leased line Answer mode |
&M0 ■ | Asynchronous mode | |
&M1 |
| Synchronous mode with |
|
| asynchronous dialling |
&M2 |
| Synchronous mode with dialling |
|
| invoked by the DTR signal |
&M4 |
| Asynchronous mode with dialling |
|
| invoked by the DTR signal |
&N0 |
| Disable abort connection |
&N1 | ■ | Enable abort connection |
&R0 | ■ | CTS follows RTS when the modem |
|
| is on line. |
&R1 |
| CTS is always asserted. |
&S0 | ■ | DSR signal will always be asserted |
&S1 |
| DSR signal asserted at the start of |
|
| handshake |
&S2 |
| DSR signal asserted at end of |
|
| handshake (before CONNECT |
|
| message) |
&Vn |
| View Active Configuration Profile |
&V0 |
| View stored configuration profile 0 |
&V1 |
| View stored configuration profile 1 |
&V2 |
| View stored configuration profile 2 |
&V3 |
| View stored configuration profile 3 |
&V8 |
| View differences between active |
|
| configuration and default settings of |
|
| the S Registers |
&Wn |
| Write Configuration Parameters |
|
| AbbreviatedCommandList | |
&W0 |
| Save current configuration into | |
|
| profile 0 |
|
&W1 |
| Save current configuration into | |
|
| profile 1 |
|
&W2 |
| Save current configuration into | |
|
| profile 2 |
|
&W3 |
| Save current configuration into | |
|
| profile 3 |
|
&X0 | ■ | Synchronous clocks generated by | |
|
| Modem. |
|
&X1 |
| Clocks generated by computer - | |
|
| external clocking. |
|
&X2 |
| Clocks generated by remote system | |
|
| - slave clocking. |
|
&Y0 |
| Select stored profile 0 on power up | |
&Y1 |
| Select stored profile 1 on power up | |
&Y2 |
| Select stored profile 2 on power up | |
&Y3 |
| Select stored profile 3 on power up | |
&Z |
| Stored Phone Number | |
#A0 |
| Prevent remote access | |
#A1 |
| Allow remote access | |
#A2 | ■ | Allow remote access with security | |
|
| password |
|
#B0 | ■ | B0 = V.23 B2 = V.22 | |
#B1 |
| B0 = V.22 B2 = V.23 | |
#C0 |
| V.25 calling tones disabled | |
#C1 | ■ | V.25 calling tones enabled | |
#CID0 | ■ | Caller ID | |
|
| disabled |
|
#CID1 | Caller ID enabled | ||
#CID2 | Caller ID enabled with | ||
|
| response to host in hex format | |
#CID3 | Caller ID enabled with | ||
|
| extended response |
|
#D0 | ■ | Disable direct calling procedures | |
#D1 |
| Enable direct calling procedures | |
#E0 | ■ | DES encryption disabled | |
#E1 |
| DES encryption enabled | |
#E2 |
| SuperSecure enabled (some models | |
|
| only) |
|
#E3 |
| DES MultiKey |
|
#E4 |
| DES AutoIV |
|
#H |
| Display Help |
|
#I0 | ■ | V.22bis leased line normal | |
#I1 |
| Use | |
|
| over leased line |
|
#J0 |
| Assume V.42 capable | |
Page 257
