Manuals / Toshiba / Computer Equipment / Label Maker

Toshiba B-EX operation manual Up to eight ROM files can be added, Start Download

Models: B-EX

1 95

Download 95 pages 36.08 Kb

Page 68

Up to eight ROM files can be added.

If the specified file is not a ROM file, or if the specified ROM file is not for the printer model selected for the Product, the error message is displayed.

Up to eight ROM files can be added.

One file per program section is accepted. In the case second file is chosen for a program section, the following confirmation message is displayed.

When [Yes] is clicked, the existing file is replaced.

When [No] is clicked, the processing is canceled.

[Delete]

When this button is clicked, selected ROM files in the [ROM List] are deleted. This button becomes active when a ROM file is selected in the [ROM List].

[Start Download...]

The ROM files in the [ROM List] are downloaded to the printer.

When this button is clicked, the following confirmation message is displayed.

When [Yes] is clicked, the processing starts. When [No] is clicked, the processing is canceled.

When reading the ROM file or creating download data failed, the error message is displayed.

When Multi LAN is selected for the interface, the [Printer List] screen is displayed to allow choosing the printers to which the files are downloaded.

When the processing starts, the progress status screen is displayed. When the processing is completed, the completion screen is displayed.

This function is executed only when the printer is in online mode and idle state. When no file is listed in the [ROM List], this button is grayed out.

After the ROM files are sent to the printer, the Product waits for the end of the printer update. Regarding the Main and Boot programs, whether or not the firmware version has been updated is confirmed at the completion of the download.

When multiple files are downloaded, the processing is repeated one by one.

The printer firmware is replaced with the specified ROM files regardless of the current printer version.

65

Image 68

Toshiba B-EX Up to eight ROM files can be added, When Yes is clicked, the existing file is replaced, Start Download

Contents

B-EX Setting Tool Operation Manual B-EX SeriesTOSHIBA Label Printer Second Edition January 25Table of Contents 2. INSTALLATION1. INTRODUCTION 3. START-UP6. APPENDIX Features 1. IntroductionSupported Printers Software License AgreementOutline of the Functions NotationScreens Used in This Document Trademark and CopyrightOperational Conditions DisclaimerSoftware Operation System Hardware2. Installation Installation ProcedureClick Finish to complete the operation These are changeable after installation6. The Start Copying Files screen appears Uninstallation 3. Start-up Printer4. Preparation Main ScreenThe settings specified in the Printer Setting screen are reflected Main view Displays the setting screen of the selected menu iconMemory Management Tab Processing related to the memoryMenus FileThis menu is used to store setup information in a specified file It also stores the status of the current setup screenWhen you do not want to store security information, click No Exit ExportEdit View This menu is used to display version information HelpContents This menu is used to display the main screen for Help About Printer Setting B-EX6T2-G and B-EX6T2-T are not approved at present Page Page Multi LAN When the export failed, the error message is displayed An added printer is inserted under the currently selected printerDelete ImportPage The setting is saved upon changed, and reflected in the header view Stop BitOptions 1 bit, 2 bitsEnvironment Password Set a password to log in the Product No password is set right after the installationCancel RangePassword Change Processing Screen Progress Bar ScreenCompletion Screen Progress Status Updating the main program Updating the system mode program Transmission and update of the main program are in progressTransmission and update of the data file are in progress Cannot confirm the printer is in online modePrinter List Screen Parameter Setting 5. FunctionsWhen this button is clicked, the following message is displayed Restore to OnlineThe printer mode is changed from the parameter setting to online Set ParameterWhen this button is clicked, the confirmation message is displayed General Tab Default TYPE 1 Compatible with current version, TYPE 2 Special specificationDefault DefaultDefault Set an even number for the LCD contrast fine adjustmentDefault DefaultDefault Range DefaultDisable Disable, Standard, ECO, ECO with Back FeedGeneral 2 Tab Default Tone Adjustment Group Thermal TransferDefault DefaultThis setting cannot be changed SHELL Select how to set the threshold for the reflective sensorDefault Command SetPassword Group System Mode Password New PasswordDefault Old Password Enter the password currently set on the printerDevice Tab Default Select Centronics ACK /BUSY signal timingDefault DefaultLAN Tab Disable, Enable, Enable External Memory WINS Select whether or not the WINS protocol is enabled DefaultDisable Disable, Enable STATIC, Enable DHCPWLAN Tab ANY SSID OFF, ANY SSID ON / Priority AP OFF Open System, Shared Key, WPA-EAP, WPA-PSK, WPA2-EAP, WPA2-PSKDefault DisableDisable, EAP-MD5, EAP-TLS, EAP-TTLS, LEAP, LEAP NetworkEAP, PEAP Authentication System SettingsWhen the code is changed, the WEP key is cleared DefaultWhen the WEP key size is changed, the WEP key is cleared 40 bits When ASCII mode is used for entries, use five alphanumeric charactersWLAN 2 Tab Set a secret key passphrase, using up to 64 alphanumeric characters DefaultInternal Authentication Select an internal authentication method DefaultPAC File Password Select whether to enable or disable the CCX optionsDefault DisableRFID Tab Default DefaultDefault DefaultMaintenance Self Diagnosis TabWhen this button is clicked, the processing starts Printer Reset The printer is resetA reset will be executed regardless of the printer status After refreshing the display, ALL is selectedMaintenance Counter Clear Select the option to clear maintenance counterDefault Clear Selected maintenance counter is cleared to zeroInitialize Memory Management Tab Default DefaultThe storage area size for printer commands is displayed DefaultPage Download Firmware DownloadWhen Yes is clicked, the existing file is replaced When No is clicked, the processing is canceled DeleteUp to eight ROM files can be added Start DownloadBASIC Download Default The storage area size for printer commands is displayedWhen checked, the starting block and the program file can be selected Starting block Specify the area where the program is storedData file Start DownloadCreate HTML/XML ROM ROM List Data configuration of the created ROM file is displayed Output File Specify a file where ROM data is saved\JPN\HTML folder File for Japanese language \JPN\PASS folder File for Japanese languageTool Tool TabCreate External Character Tab When Type = 51, Code = FFFF G51FFFF.bmp or G51FFF000.bmp DefaultWhen Location = Onboard Flash Memory 01 to 44 When Location = USB Memory 01 to 44, 51 to0.5 x 0.5, 1.0 x 1.0, 2.0 x 2.0, 3.0 x 3.0, 1.0 x 2.0, 2.0 x Output File Specify the file where the external character is stored A Bitmap External Character Command is created with nibble dataThe file extension is gai CreateTest Print Tab Default Issue Mode Select an issue modeDefault DefaultSlant Lines 1 dot Characters Slant Lines 3 dot Barcodes6. Appendix Error Message List When using hex. format, enter a 10-digit or 26-digit When using ASCII, enter a 5-digit or 13-digitspecified on the Printer Setting screen Printer Setting screenCreating an External Character command failed The file where the image to be printed is stored cannot beprinting cannot be performed, re-install the Generating a print command failedSetup Items List General TabTransmissive Sensor with Back Feed Disable DisableEnable DisableTone Adjustment General 2 TabSetup group Setup itemDefault Device TabSetup group Setup itemDefault LAN TabSetup group Setup itemDefault WLAN TabDefault Key DisableDisable DisableSetup group Setup itemDefault WLAN 2 TabSetup group Setup itemDefault RFID Tab