Manuals / Toshiba / Computer Equipment / Label Maker

Toshiba B-EX These are changeable after installation, The Start Copying Files screen appears

Models: B-EX

1 95

Page 9

5. The [Selection of Initial Setting] screen appears. Select a language used for the Product, a printer model to be connected and its destination from the pull down menus.

These are changeable after installation.

6. The [Start Copying Files] screen appears.

Check the descriptions under [Current Settings] and click [Next] when the descriptions are correct. Then, the installation starts.

When you want to change the setting, click [Back] until the applicable screen appears, then make the change.

7. The installation is being performed. Click [Cancel] to stop the installation.

8. The [InstallShield Wizard Complete] screen appears when the installation is completed.

Click [Finish] to complete the operation.

Page 9

Image 9

Toshiba B-EX operation manual These are changeable after installation, The Start Copying Files screen appears

Contents

B-EX Series B-EX Setting Tool Operation ManualTOSHIBA Label Printer Second Edition January 252. INSTALLATION Table of Contents1. INTRODUCTION 3. START-UP6. APPENDIX 1. Introduction FeaturesSupported Printers Software License AgreementNotation Outline of the FunctionsTrademark and Copyright Screens Used in This DocumentDisclaimer Operational ConditionsSoftware Operation System HardwareInstallation Procedure 2. InstallationThese are changeable after installation 6. The Start Copying Files screen appearsClick Finish to complete the operation Uninstallation Printer 3. Start-upMain Screen 4. PreparationMain view Displays the setting screen of the selected menu icon The settings specified in the Printer Setting screen are reflectedMemory Management Tab Processing related to the memoryFile MenusIt also stores the status of the current setup screen This menu is used to store setup information in a specified fileWhen you do not want to store security information, click No Exit ExportEdit View Help Contents This menu is used to display the main screen for Help AboutThis menu is used to display version information Printer Setting B-EX6T2-G and B-EX6T2-T are not approved at present Page Page Multi LAN An added printer is inserted under the currently selected printer When the export failed, the error message is displayedDelete ImportPage Stop Bit The setting is saved upon changed, and reflected in the header viewOptions 1 bit, 2 bitsEnvironment No password is set right after the installation Password Set a password to log in the ProductCancel RangePassword Change Progress Bar Screen Processing ScreenCompletion Screen Progress Status Transmission and update of the main program are in progress Updating the main program Updating the system mode programTransmission and update of the data file are in progress Cannot confirm the printer is in online modePrinter List Screen 5. Functions Parameter SettingRestore to Online When this button is clicked, the following message is displayedThe printer mode is changed from the parameter setting to online Set ParameterWhen this button is clicked, the confirmation message is displayed General Tab TYPE 1 Compatible with current version, TYPE 2 Special specification DefaultDefault DefaultSet an even number for the LCD contrast fine adjustment DefaultDefault DefaultDefault Default RangeDisable Disable, Standard, ECO, ECO with Back FeedGeneral 2 Tab Tone Adjustment Group Thermal Transfer DefaultDefault DefaultSelect how to set the threshold for the reflective sensor This setting cannot be changed SHELLDefault Command SetNew Password Password Group System Mode PasswordDefault Old Password Enter the password currently set on the printerDevice Tab Select Centronics ACK /BUSY signal timing DefaultDefault DefaultLAN Tab Disable, Enable, Enable External Memory Default WINS Select whether or not the WINS protocol is enabledDisable Disable, Enable STATIC, Enable DHCPWLAN Tab Open System, Shared Key, WPA-EAP, WPA-PSK, WPA2-EAP, WPA2-PSK ANY SSID OFF, ANY SSID ON / Priority AP OFFDisable DefaultDisable, EAP-MD5, EAP-TLS, EAP-TTLS, LEAP, LEAP NetworkEAP, PEAP Authentication System SettingsDefault When the code is changed, the WEP key is clearedWhen the WEP key size is changed, the WEP key is cleared 40 bits When ASCII mode is used for entries, use five alphanumeric charactersWLAN 2 Tab Default Set a secret key passphrase, using up to 64 alphanumeric charactersInternal Authentication Select an internal authentication method DefaultSelect whether to enable or disable the CCX options PAC File PasswordDefault DisableRFID Tab Default DefaultDefault DefaultSelf Diagnosis Tab MaintenancePrinter Reset The printer is reset When this button is clicked, the processing startsA reset will be executed regardless of the printer status After refreshing the display, ALL is selectedSelect the option to clear maintenance counter Maintenance Counter ClearDefault Clear Selected maintenance counter is cleared to zeroInitialize Memory Management Tab Default DefaultThe storage area size for printer commands is displayed DefaultPage Firmware Download DownloadWhen No is clicked, the processing is canceled Delete When Yes is clicked, the existing file is replacedUp to eight ROM files can be added Start DownloadBASIC Download The storage area size for printer commands is displayed DefaultWhen checked, the starting block and the program file can be selected Starting block Specify the area where the program is storedStart Download Data fileCreate HTML/XML ROM Output File Specify a file where ROM data is saved ROM List Data configuration of the created ROM file is displayed\JPN\HTML folder File for Japanese language \JPN\PASS folder File for Japanese languageTool Tab ToolCreate External Character Tab Default When Type = 51, Code = FFFF G51FFFF.bmp or G51FFF000.bmpWhen Location = Onboard Flash Memory 01 to 44 When Location = USB Memory 01 to 44, 51 to0.5 x 0.5, 1.0 x 1.0, 2.0 x 2.0, 3.0 x 3.0, 1.0 x 2.0, 2.0 x A Bitmap External Character Command is created with nibble data Output File Specify the file where the external character is storedThe file extension is gai CreateTest Print Tab Issue Mode Select an issue mode DefaultDefault DefaultSlant Lines 3 dot Barcodes Slant Lines 1 dot Characters6. Appendix Error Message List When using ASCII, enter a 5-digit or 13-digit When using hex. format, enter a 10-digit or 26-digitspecified on the Printer Setting screen Printer Setting screenThe file where the image to be printed is stored cannot be Creating an External Character command failedprinting cannot be performed, re-install the Generating a print command failedGeneral Tab Setup Items ListTransmissive Sensor with Back Feed Disable DisableEnable DisableGeneral 2 Tab Tone AdjustmentSetup item Setup groupDefault Device TabSetup item Setup groupDefault LAN TabSetup item Setup groupDefault WLAN TabDisable Default KeyDisable DisableSetup item Setup groupDefault WLAN 2 TabSetup item Setup groupDefault RFID Tab