Manuals / Toshiba / Computer Equipment / Label Maker

Toshiba B-EX operation manual Firmware Download

Models: B-EX

1 95

Download 95 pages 36.08 Kb

Page 67

Download

Download

The Download menu enables downloading the printer firmware and BASIC program.

When the [Download] icon on the menu icon area is clicked, the [Download] screen is displayed.

Firmware Download

Be sure to avoid the environment where a power failure may occur in the middle of the downloading. If a power failure occurs during a firmware updating, the printer may not start up.

Even when the printer can normally start up, download the firmware again. If cannot, please contact TOSHIBA TEC sales representative.

[ROM List]

ROM files of the firmware to be downloaded to the printer are displayed. No file has been displayed as default.

ROM files are listed by program section, rather than in chronological order. The program sections are sorted in the order of BOOT, MAIN, C/G, XML, WMON, KANJI, and CHINESE.

Downloading is performed from the top of the list.

When a ROM file is selected, the firmware information is displayed under the list.

[Add...]

Specified ROM files are added to the [ROM List].

When this button is clicked, the file selection screen appears. Choose a ROM file, click [Open], and this ROM file is added to the [ROM List].

64

Image 67

Toshiba B-EX operation manual Firmware Download

Contents

Second Edition January 25 B-EX Setting Tool Operation ManualB-EX Series TOSHIBA Label Printer3. START-UP Table of Contents2. INSTALLATION 1. INTRODUCTION6. APPENDIX Software License Agreement Features1. Introduction Supported PrintersNotation Outline of the FunctionsTrademark and Copyright Screens Used in This DocumentHardware Operational ConditionsDisclaimer Software Operation SystemInstallation Procedure 2. Installation6. The Start Copying Files screen appears These are changeable after installationClick Finish to complete the operation Uninstallation Printer 3. Start-upMain Screen 4. PreparationProcessing related to the memory The settings specified in the Printer Setting screen are reflectedMain view Displays the setting screen of the selected menu icon Memory Management TabFile MenusExport This menu is used to store setup information in a specified fileIt also stores the status of the current setup screen When you do not want to store security information, click No ExitEdit View Contents This menu is used to display the main screen for Help About HelpThis menu is used to display version information Printer Setting B-EX6T2-G and B-EX6T2-T are not approved at present Page Page Multi LAN Import When the export failed, the error message is displayedAn added printer is inserted under the currently selected printer DeletePage 1 bit, 2 bits The setting is saved upon changed, and reflected in the header viewStop Bit OptionsEnvironment Range Password Set a password to log in the ProductNo password is set right after the installation CancelPassword Change Progress Bar Screen Processing ScreenCompletion Screen Progress Status Cannot confirm the printer is in online mode Updating the main program Updating the system mode programTransmission and update of the main program are in progress Transmission and update of the data file are in progressPrinter List Screen 5. Functions Parameter SettingSet Parameter When this button is clicked, the following message is displayedRestore to Online The printer mode is changed from the parameter setting to onlineWhen this button is clicked, the confirmation message is displayed General Tab Default DefaultTYPE 1 Compatible with current version, TYPE 2 Special specification DefaultDefault DefaultSet an even number for the LCD contrast fine adjustment DefaultDisable, Standard, ECO, ECO with Back Feed Default RangeDefault DisableGeneral 2 Tab Default DefaultTone Adjustment Group Thermal Transfer DefaultCommand Set This setting cannot be changed SHELLSelect how to set the threshold for the reflective sensor DefaultOld Password Enter the password currently set on the printer Password Group System Mode PasswordNew Password DefaultDevice Tab Default DefaultSelect Centronics ACK /BUSY signal timing DefaultLAN Tab Disable, Enable, Enable External Memory Disable, Enable STATIC, Enable DHCP WINS Select whether or not the WINS protocol is enabledDefault DisableWLAN Tab Open System, Shared Key, WPA-EAP, WPA-PSK, WPA2-EAP, WPA2-PSK ANY SSID OFF, ANY SSID ON / Priority AP OFFAuthentication System Settings DefaultDisable Disable, EAP-MD5, EAP-TLS, EAP-TTLS, LEAP, LEAP NetworkEAP, PEAPWhen ASCII mode is used for entries, use five alphanumeric characters When the code is changed, the WEP key is clearedDefault When the WEP key size is changed, the WEP key is cleared 40 bitsWLAN 2 Tab Default Set a secret key passphrase, using up to 64 alphanumeric charactersDefault Internal Authentication Select an internal authentication methodDisable PAC File PasswordSelect whether to enable or disable the CCX options DefaultRFID Tab Default DefaultDefault DefaultSelf Diagnosis Tab MaintenanceAfter refreshing the display, ALL is selected When this button is clicked, the processing startsPrinter Reset The printer is reset A reset will be executed regardless of the printer statusClear Selected maintenance counter is cleared to zero Maintenance Counter ClearSelect the option to clear maintenance counter DefaultInitialize Memory Management Tab Default DefaultDefault The storage area size for printer commands is displayedPage Firmware Download DownloadStart Download When Yes is clicked, the existing file is replacedWhen No is clicked, the processing is canceled Delete Up to eight ROM files can be addedBASIC Download Starting block Specify the area where the program is stored DefaultThe storage area size for printer commands is displayed When checked, the starting block and the program file can be selectedStart Download Data fileCreate HTML/XML ROM \JPN\PASS folder File for Japanese language ROM List Data configuration of the created ROM file is displayedOutput File Specify a file where ROM data is saved \JPN\HTML folder File for Japanese languageTool Tab ToolCreate External Character Tab When Location = USB Memory 01 to 44, 51 to When Type = 51, Code = FFFF G51FFFF.bmp or G51FFF000.bmpDefault When Location = Onboard Flash Memory 01 to 440.5 x 0.5, 1.0 x 1.0, 2.0 x 2.0, 3.0 x 3.0, 1.0 x 2.0, 2.0 x Create Output File Specify the file where the external character is storedA Bitmap External Character Command is created with nibble data The file extension is gaiTest Print Tab Default DefaultIssue Mode Select an issue mode DefaultSlant Lines 3 dot Barcodes Slant Lines 1 dot Characters6. Appendix Error Message List Printer Setting screen When using hex. format, enter a 10-digit or 26-digitWhen using ASCII, enter a 5-digit or 13-digit specified on the Printer Setting screenGenerating a print command failed Creating an External Character command failedThe file where the image to be printed is stored cannot be printing cannot be performed, re-install theGeneral Tab Setup Items ListTransmissive Sensor with Back Feed Disable DisableDisable EnableGeneral 2 Tab Tone AdjustmentDevice Tab Setup groupSetup item DefaultLAN Tab Setup groupSetup item DefaultWLAN Tab Setup groupSetup item DefaultDisable Default KeyDisable DisableWLAN 2 Tab Setup groupSetup item DefaultRFID Tab Setup groupSetup item Default