Initial Configuration, Changing Your Password | Tut Systems SMS2000

Initial Configuration

Initial Configuration

There are five steps required for the initial configuration of the SMS2000:

1.Step 1 Change the password for security purposes.

2.Step 2 Set the Quick Configuration.

3.Step 3 Change the system hostname to identify the system on the network.

4.Step 4 Disable authentication.

5.Step 5 Save the configuration.

6.Step 6 Reboot the system.

7.Step 7 Verify connectivity.

For advanced configuration information, see the SMS2000 User’s Guide.

For information on using OCS with the SMS2000, see the OCS User’s Guide.

Changing Your Password

You are encouraged to change the initial configuration password, “manager,” after your initial login to the SMS2000. Perform the following steps to change your password:

1.At the system prompt enter: sms2000% passwd

2.Press <Enter>.

3.Enter your new password.

4.Press <Enter>.

The system asks you to verify your password.

5.Reenter your password.

6.Press <Enter>.

Note: If you forget your password at any time, please call your Tut Systems

Customer Service representative to assist you in logging on again.

You must have access to the serial port and have a phone nearby when contacting Customer Service to bypass your password.

Setting the Quick Configuration

To reset the entire system configuration, using the IP address, network mask, default gateway, and DNS servers specified in the basic system configuration, use this command:

set quick-config{ip_address/masklen ip_address netmask ip_mask} gateway dns[dns] [dns]

TUT Systems, Inc

Page 22 of 104

P/N 220-06288-20

Image 22

Tut Systems SMS2000 manual Initial Configuration, Changing Your Password, Setting the Quick Configuration

Contents

TUT Systems SMS2000 User Guide SMS2000 User’s Guide SMSUser’s Guide Contents Configuring Snmp Polling Configuring SmtpConfiguring NTP Connectivity and Testing Authentication with Radius Authentication Configuring the Command ServerAuthentication Authorization Groups Using Rule PrioritiesConfiguring Radius SMS2000 Rules SMS2000 Troubleshooting Procedures Using Both Radius and OCS AuthenticationWeb Proxy Settings SMS2000 Status Attributes and Statistics List of Tables Radius Attributes in Access-Accept PacketsList of Figures Documentation available for this Release PrefaceAudience Related Documentation Subscriber Management Features Introduction Introduction Subscriber Management Components Subscriber Management Components SMS2000 OCS Introduction Getting Started User Interface Ifconfig portnumber ipaddress /masklen Accessing Help for CommandsFor example restore config web original-confi g Style Conventions Cursor Movement Cursor Motion Keystrokes Establishing a Connection with the SMS2000 Initial ConfigurationClick Configure Establishing a Connection Via a Serial Interface Establishing a Connection Via Telnet Initial Configuration Changing Your Password Initial ConfigurationSetting the Quick Configuration Disabling Authentication Setting the HostnameSaving the Configuration Verifying the Configuration Rebooting the SystemReboot Setting the Default Configuration E-mail System AdministrationConfiguration E-Mail Settings Set config-mailrecipient@SMTPserver SMTPserver Deleting the Configuration E-mail Configuration and System File ToolsMailing the Current Configuration Committing Configuration Changes Commit auto Automatically Committing Configuration ChangesDisabling Automatic Configuration Changes Commit noauto Loading a Configuration File Saving a ConfigurationRestoring a Previous Configuration Setting the Smtp Server Configuring SmtpRestoring the Default Configuration Deleting the Smtp Server Setting the Timezone Configuring NTPSetting the Smtp ID Set smtpid on off Setting the Time Configuring Snmp PollingConfiguring the NTP server Enabling Snmp Polling Disabling Snmp Polling Testing to See if Snmp Polling will WorkSnmp-pollmacaddress Setting Specialized System Options Connectivity and TestingTesting Connectivity System Tools Leftrighthelp ? Setting and Deleting Static PortsDefining Ports Port-definition mixed tut vlan Event Tracking Disconnecting a Session on a PortSetting the Syslog Server Displaying Log Messages Displaying Version Information System Administration ToolsExiting the Management Session Passwd Changing a PasswordDisplaying Control Keys Keys Snmp System Contact Snmp ManagementSnmp Agent Snmp System Location Snmp Community Snmp Trap Recipient SMS2000% snmp delete trap-recipient Troubleshooting ToolsSystem Information Tools Show snmp trap-recipient Setting the ARP Failure Limit Subscriber Connectivity CommandsUpgrades Setting the ARP Polling Period Upgrading from Tut Systems’ Website Archiving SMS2000 Firmware and distributing it from a Server Returning to an Older Firmware Version Verifying a Successful UpgradeLoading Another Image System Administration Authentication Authentication Deleting the Command Server Configuring the Command ServerSetting the Command Server for OCS Interaction Adding the OCS as the Authentication Server Auth add web url secret secret cmd-serv Deleting an Authentication ServerTesting Authentication Auth on Auth off forcedweb authokurl blockall Setting the Authentication IntervalBypassing Authentication Auth interval minutes off Allow-Nets Setting the Http Request ThrottleHttp Request Throttle Deleting the Http Request Throttle Setting an Allow-Net Set allow-netipaddress netmask dns-name Deleting an Allow-Net Setting the Automatic Redirection URLAutomatic Redirection URLs Set authok url Adding a Radius Server Authentication with RadiusDeleting the authok Delete authok Command Syntax Description Default retrans-primary-only is DefaultUsage Guidelines Example Set nas-port-type integer Set NAS port type parameterSet nas-port-type Show status radius Testing Authentication on the Radius ServerConfiguring a Radius SSL Back Channel Show status radius Example Authorization AuthorizationAuthorization Server Functionality Accounting AccountingSending Accounting Messages to a Syslog Server Sending Accounting Messages to a Radius Server Radius Accounting ConfigurationConfiguring Accounting Parameters Deleting a Radius Accounting Server Provisioning Provisioning Billing Billing Adding a Group Service Creation Using Groups and RulesGroups Group add groupname noinherit inherit groupname Setting Maximum Users Per Port Setting the Active Group ContextSubscribers that Cannot Support Authentication Deleting a Group Deleting a Rule SMS2000 RulesAdding a Rule Set rule rulename groupname priority rulestring MAC Address Rule Expression ComponentsIP Address Ip=ipaddress ,netmask Vlan=vlanida-vlanidb Not OperatorTut=ipaddress-linenum*-portnum Parenthesis OperatorOr Operator Expression and expression Using Rule Priorities IP Addressing IP AddressingPlug and Play With NAT Static Routable Addresses Dhcp Pools Static Non-Routable Addresses IP Multicasting Iptype default NAT static Dhcp 1to1 1to1Unique Configuring IP TypesUnderstanding 1to1 and 1to1 Unique IP Types Source-Nets Setting a Source-NetDeleting a Configured Source-Net Set source-netstartaddress endaddress subnet-mask Removing a Dhcp Assignment Setting the DNS Server AddressCreating Dhcp Pools Dhcp-server release macaddress Adding Routes Static RoutesDeleting the DNS Server Address Set dns add ipaddress Printing Setting up the LPR HostSet lpr hostname off queuename maxpages maxbytes Configuring Radius Using SMS2000 with a Radius ServerObtaining the Radius Server Software Adding the SMS2000 as a Client on the Radius Server Configuring Service ParametersAdding Users to the Radius Server Using Real IP Addresses Radius Ports SMS2000 NAS File SMS2000 Status Attributes and StatisticsRadius Attributes Sent in Accounting Messages Radius Attributes Sent In Access Request Packets Using Both Radius and OCS AuthenticationRadius Attributes Received in Access- Accept Packets Shape xbps/rbps Setting Traffic ShapingDeleting Traffic Shaping Shape xbps/rbps delete Setting the PMS Server SMS2000 and Property Management Systems PMS Protocol Modes TTY ACK-NAK ENQ-ACK-NAK ENQ-ACK-NAK Mode Files For Groups Customizing SMS2000 Web Authentication with RadiusLoading and Deleting Customized Web Pages Loading Web Pages or Files Path Components Load web url defaultsImage Links Deleting Web Pages or Files Customizing Web PagesUpgrading Preserving the Web Form Size For Web Pages and External Links Web Page Redirection Viewing Customizations Active Page ComponentsReference Setting the Wpad Curl Configuring Web Proxy SettingsWeb Proxy Settings Setting the Wpad Timeout Web Proxy Server Delete proxy-ports port Set proxy-ports portShow proxy-ports SMS2000 Troubleshooting SMS2000 Troubleshooting Procedures Browser Snmp PollingMultiple frames opened Unable to do credit card Verify OCS screens off Line Appendix a Radius Access-Accept Dictionary File Radius Attributes in Access-Accept Packets Appendix Appendix TUT Systems, Inc 100 Internet Telephone Appendix B Technical Assistance and Customer SupportTechnical Support Equipment Return and Repair Limitations of Warranty Appendix C SMS2000 Limited WarrantyHardware Limited Warranty Exclusive Remedies Assistance Electrical Safety AdvisoryTut Systems, Inc., Customer Service Department FCC Radio Frequency Interference Statement TUT Systems, Inc 104