Uniden EXP1240 Table 12: , and , parameters

EXP1240 System Installation Guide Revision 06

© 2013 Uniden America Corp. PROPRIETARY AND CONFIDENTIAL Page 51 of 71

Table 12:

Add extension

and

Edit extension

parameters

Parameter Description

Extension Enter the handset phone number or SIP username as configured on

the SIP server or VoIP PBX.

Authentication User

Name and Password

Enter the name and password you use to log into the selected SIP

server.

Display Name Enter the name the system should display for this extension (up to

10 characters).

Mailbox Name E nter the name of the voice mailbox this extension should use.

Server Select the SIP server this extension is programmed on.

Forwarding

Unconditional

Number

Forward all calls: Enter the number the system should forward calls

to. Select Enable to turn call forwarding on or Disable to leave it off.

Forwarding No

Answer Number

Forward on no answer: Enter the number the system should

forward calls to when this extension does not answer, then enter

the number of seconds you want the system to wait in the field to

the right. Select Enable to turn call forwarding on or Disable to leave

it off.

Forwarding on Busy

Number

Forward on busy: Enter the number the system should forward calls

to when this extension is busy. Select Enable to turn call forwarding

on or Disable to leave it off.

Contents

Main EXP1240 SIP DECT System: Installation Guide Contents Page Table of Figures List of Tables Page Introduction Important Safety Instructions! Check the Box Contents About This Document Purpose and Audience Manual Conventions Terms used in this manual Table 1: Terms Table 2: Abbreviations Hardware Setup Base Station Figure 3 Connecting the base station Table 3: Base station LEDs and their meanings Wall mounting the base station Be sure the wall material can hold the weight of the base. Figure 4: Base mounting dimensions Page Charging the battery Figure 7: Installing the handset battery Charge each battery completely (about 10 hours) before using it. Figure 8: Inserting the handset into the charger Powering on the Handset Initial System Configuration Table 4: Summary: Basic system configuration Using the Base Station Interface Figure 9: screen Configuring General System Settings Change Configuration and Management Settings Figure 10: screen Change the Default Password Figure 11: screen Change the PSTN Tones and Emergency Dialing If the system connects to the PSTN in the US or Canada, skip this section. Configure the Network Settings Screen Configure Time Settings Figure 14: screen Figure 15: Checking time settings updates Configuring the SIP Server Settings Figure 16: screen Page To edit an existing server To delete a server Program the SIP Extensions Figure 17: screen Register Handsets to Extensions Figure 18: screen, no handsets registered Figure 19: screen, one handset registered To deregister a handset Multiple Base (Multi-cell) Systems Introduction Timing Levels System Chain ID and RPN Page Table 5: Sample multi-cell system information Setting Up a Multi-cell System Table 6: Summary: Multi-cell system configuration Configuring the Primary Base Station Figure 22: screen (default values) Figure 23: screen (primary base enabled) Configuring Level 1 Base Stations Page Figure 26: table, synchronization complete ( screen) Figure 27: table, Level 1 complete ( Configuring Base Stations at Level 2 and Up Removing Base Station(s) from a Multi-Cell System Changing the Primary Base Station in a Chain Only perform this procedure when the system is offline or in a maintenance period. Page System Maintenance Backing Up Configuration Settings Figure 29: screen Restoring a Configuration Updating the Firmware Setting Up Firmware Folders Valid server, folder, and firmware file name examples (base stations) Valid server, folder, and firmware file name examples (handsets) Configuring the Firmware Update Settings Figure 30: server information Table 7 Firmware path examples Updating Base Station Firmware Figure 31: screen Updating Handsets Figure 32: Firmware update progress ( screen) To verify the firmware update Appendix A: Software Reference Base Station Configuration Interface Available Screens Global Buttons and Options Home/Status Screen (Read Only) Extensions Screen Table 10: options Table 11: parameters (read only) Add Extension and Edit Extension screens Table 12: and parameters Servers Screen Page Network Screen Table 15: parameters Table 16: parameters Table 17: parameters Table 18: parameters Table 19: parameters Management Screen Table 20: parameters Page Firmware Update Screen Table 21: screen options Table 22: parameters , clicking Save will start the firmware update process for that handset type. parameters Time Screen Table 25: parameters Page Page Importing a new file will replace the existing contact list. Multi Cell Screen Table 26: parameters Table 27: parameters Table 28: parameters Table 29: parameters Configuration Screen (read only) Page Page Appendix B: RFPI Numbers