Manuals / Brands / Communications / Two-Way Radio / Uniden / Communications / Two-Way Radio

Uniden EXP1240 Figure 26: , table, synchronization complete (, screen)

1 71

Download 71 pages, 4.79 Mb

EXP1240 System Installation Guide Revision 06

© 2013 Uniden America Corp. PROPRIETARY AND CONFIDENTIAL Page 35 of 71

∘ The IP Status field of the base station you are logged into should show This

unit. Any other base stations in this chain should show Connected (i.e.,

connected to the network and functioning properly) as their IP status. If any

base station shows Connection Loss as its IP status, that base station is not

connected to the network or has lost power.

∘ The primary base station always serves as its own sync source, so the DECT

sync source field should display Primary:RPN{its own RPN}. The DECT

Property field shows Primary.

∘ This base station's DECT sync source will show (any) RPN and its DECT

Property field will show Locked.

∘ Check the DECT sync source drop-down box for this base station to verify

that there is a selection for the primary base station with a dBm value. If

there is not a dBm value, wait for the system to further synchronize

(approximately 2 minutes). When there is a dBm value, select the primary

base station from the DECT sync source drop-down box and click Save.

∘ If the primary base station is not on the list or if the signal strength is below -

70 to -73 dBm (-74dBm or less), move this base station to a different

location. (You could also configure the other Level 1 base stations first and

then come back and configure this one at Level 2.)

∘ The DECT Chain appears at the bottom of the display and shows the

synchronization source for all base stations in this system. Until the primary

base station is selected as the DECT sync source, there will be a warning in

the DECT Chain for this base station.

Figure 26:

Base Station Group

table, synchronization complete (

Multi-cell

screen)

13) When the system has finished synchronizing, repeat this process for each base station at

Level 1.

Contents

Main EXP1240 SIP DECT System: Installation Guide Contents Page Table of Figures List of Tables Page Introduction Important Safety Instructions! Check the Box Contents About This Document Purpose and Audience Manual Conventions Terms used in this manual Table 1: Terms Table 2: Abbreviations Hardware Setup Base Station Figure 3 Connecting the base station Table 3: Base station LEDs and their meanings Wall mounting the base station Be sure the wall material can hold the weight of the base. Figure 4: Base mounting dimensions Page Charging the battery Figure 7: Installing the handset battery Charge each battery completely (about 10 hours) before using it. Figure 8: Inserting the handset into the charger Powering on the Handset Initial System Configuration Table 4: Summary: Basic system configuration Using the Base Station Interface Figure 9: screen Configuring General System Settings Change Configuration and Management Settings Figure 10: screen Change the Default Password Figure 11: screen Change the PSTN Tones and Emergency Dialing If the system connects to the PSTN in the US or Canada, skip this section. Configure the Network Settings Screen Configure Time Settings Figure 14: screen Figure 15: Checking time settings updates Configuring the SIP Server Settings Figure 16: screen Page To edit an existing server To delete a server Program the SIP Extensions Figure 17: screen Register Handsets to Extensions Figure 18: screen, no handsets registered Figure 19: screen, one handset registered To deregister a handset Multiple Base (Multi-cell) Systems Introduction Timing Levels System Chain ID and RPN Page Table 5: Sample multi-cell system information Setting Up a Multi-cell System Table 6: Summary: Multi-cell system configuration Configuring the Primary Base Station Figure 22: screen (default values) Figure 23: screen (primary base enabled) Configuring Level 1 Base Stations Page Figure 26: table, synchronization complete ( screen) Figure 27: table, Level 1 complete ( Configuring Base Stations at Level 2 and Up Removing Base Station(s) from a Multi-Cell System Changing the Primary Base Station in a Chain Only perform this procedure when the system is offline or in a maintenance period. Page System Maintenance Backing Up Configuration Settings Figure 29: screen Restoring a Configuration Updating the Firmware Setting Up Firmware Folders Valid server, folder, and firmware file name examples (base stations) Valid server, folder, and firmware file name examples (handsets) Configuring the Firmware Update Settings Figure 30: server information Table 7 Firmware path examples Updating Base Station Firmware Figure 31: screen Updating Handsets Figure 32: Firmware update progress ( screen) To verify the firmware update Appendix A: Software Reference Base Station Configuration Interface Available Screens Global Buttons and Options Home/Status Screen (Read Only) Extensions Screen Table 10: options Table 11: parameters (read only) Add Extension and Edit Extension screens Table 12: and parameters Servers Screen Page Network Screen Table 15: parameters Table 16: parameters Table 17: parameters Table 18: parameters Table 19: parameters Management Screen Table 20: parameters Page Firmware Update Screen Table 21: screen options Table 22: parameters , clicking Save will start the firmware update process for that handset type. parameters Time Screen Table 25: parameters Page Page Importing a new file will replace the existing contact list. Multi Cell Screen Table 26: parameters Table 27: parameters Table 28: parameters Table 29: parameters Configuration Screen (read only) Page Page Appendix B: RFPI Numbers