Display

Parameter Name

Setting

 

Range

 

Default

Appears If

 

Description

 

 

 

 

 

 

[Attn]

Attention

 

[AL;L1]

[AL;L2] [AL;L3]

[AL;L4]

 

an alarm or error mes-

 

An active message will cause the

 

Alarm Low 1 to 4

 

 

sage is active.

 

display to toggle between the

 

[AL;h1]

[AL;h2] [AL;h3]

[AL;h4]

 

 

 

normal settings and the active

 

Alarm High 1 to 4

 

 

 

 

message in the upper display and

 

[AL;E1]

[AL;E2] [AL;E3]

[AL;E4]

 

 

 

[Attn] in the lower display.

 

Alarm Error 1 to 4

 

 

 

 

Your response will depend on the

 

[Er;i1]

[Er;i2] Error Input 1 or 2

 

 

 

message and the controller set-

 

[Li;L1]

[Li;L2] Limit Low 1 or 2

 

 

 

tings. Some messages, such as

 

 

 

 

 

[Li;h1]

[Li;h2] Limit High 1 or 2

 

 

 

Ramping and Tuning, indicate

 

 

 

 

 

[Li;E1]

[Li;E2] Limit Error 1 or 2

 

 

 

that a process is underway. If

 

 

 

 

 

[tUn1] Tuning

 

 

 

 

the message was generated by a

 

 

 

 

 

latched alarm or limit condition,

 

[`rP1] Ramping

 

 

 

 

the message can be cleared when

 

[LP;o1] Loop Open Error

 

 

 

 

the condition no longer exists. If

 

[LP;r1] Loop Reversed Error

 

 

 

an alarm has silencing enabled, it

 

[`C;Er] Current Error

 

 

 

 

can be silenced.

 

 

 

 

 

 

[`h;Er] Heater Error

 

 

 

 

Push the Advance Key to display

 

 

 

 

 

 

 

 

 

 

 

 

[ignr] in the upper display and

 

 

 

 

 

 

 

the message source (such as

 

 

 

 

 

 

 

[Li;h1]) in the lower display.

 

 

 

 

 

 

 

Use the Up ¿ and Down ¯ keys to

 

 

 

 

 

 

 

scroll through possible responses,

 

 

 

 

 

 

 

such as Clear [`CLr] or Silence

 

 

 

 

 

 

 

[`SiL]. Then push the Advance

 

 

 

 

 

 

 

‰ or Infinity ˆ key to execute

 

 

 

 

 

 

 

the action.

 

 

 

 

 

 

[P;St1]

Profile Start

 

0 to 40

 

 

0

the controller includes

 

Select a profile or step number that

 

 

 

 

 

profiling (PM6 R _ _

 

will be affected by Profile Action.

 

 

 

 

 

_-_ _ _ _ _ _ _).

 

 

 

 

 

 

 

[P;AC1]

Profile Action Request

 

[nonE] No Action

 

None

the controller includes

 

Select the action to apply to the

 

[ProF} Start a Profile

 

 

profiling (PM6 R _ _

 

profile (1 to 4) or step selected in

 

[StEP]

Start a Step

 

 

_-_ _ _ _ _ _ _).

 

Profile Start.

 

 

 

 

 

 

[PAUS] Pause

 

 

 

 

 

 

 

 

 

 

 

 

[rESU] Resume

 

 

 

 

 

 

[`End] End

 

 

 

 

 

 

 

 

 

 

 

Parameters that appear only in the Home Page

Watlow EZ-ZONE®PM Integrated Controller

• 27 •

Chapter 4 Home Page