Dis-

Parameter Name

 

Set-

Range

Default

Appears If

play

 

Description

 

tings

 

 

 

[`P;EL]

Input (1 or 2)

 

 

 

-100.0 to 1,000.0

0.0

Sensor Type is set to Mil-

[ P.EL]

Process Error Low

 

 

 

 

livolts, Volts, Milliamps

 

If the process value drops below this value,

 

 

 

or Potentiometer 1 kΩ,

 

it will trigger an input error.

 

 

 

 

and Error Enable is set

 

 

 

 

 

 

 

to Low.

 

 

 

 

 

 

 

 

[`FiL]

Input (1 or 2)

 

 

 

0.0 to 60.0 seconds

0.5

always

[ FiL]

Filter Time

 

 

 

 

 

 

 

Filtering smooths out the process signal to

 

 

 

 

 

both the display and the input. Increase

 

 

 

 

 

the time to increase filtering.

 

 

 

 

 

 

 

 

 

 

 

 

 

[`i;Er]

Input (1 or 2)

 

 

 

[`off] Off

Off

always

[ i.Er]

Error Latching

 

 

[``on] On

 

 

 

Turn input error latching on or off. If

 

 

 

 

 

 

latching is on errors must be manually

 

 

 

 

 

cleared.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[`dEC]

Input (1 or 2)

 

 

 

[```0] Whole

Whole

always

[ dEC]

Decimal

 

 

 

[``0;0] Tenths

 

 

 

Set the precision of the displayed value.

 

[`0;00] Hundredths

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[0;000] Thousandths

 

 

 

 

 

 

 

 

 

 

[`S;bA]

Input 1

 

 

 

[`oFF] Off

Off

PM6 _ _ _ _-_ L _ _ A A A.

[ S.bA]

Sensor Backup Enable

 

 

[``on] On

 

 

 

If the input 1 sensor fails, the controller

 

 

 

 

 

will use the input 2 sensor.

 

 

 

 

 

 

 

 

 

 

 

 

 

[`dio]

 

[```5]

[```6]

 

 

 

[`Set]

 

[`dio]

[`dio]

 

 

 

Digital Input/

Digital Input or

Digital Input or

 

 

Output Menu

Output 5

Output 6

(menu appears if PM6 _ [2 or 4] _ _-_ _ _ _ A _ _)

 

 

 

 

 

 

 

[`dir]

Digital Input/Output (5 or 6)

 

 

[OtPt] Output

Output

always

[ dir]

Direction

 

 

 

[``in] Input Voltage

 

 

 

Set the function to an input or output.

 

 

[iCon] Input Dry Contact

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[``Fn]

Digital Output (5 or 6)

 

 

[`oFF] Off

Off

Direction is set to Out-

[ Fn]

Function

 

 

 

[CooL] Cool

 

put.

 

Select what function will drive this output.

 

[hEAt] Heat

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[ALM] Alarm

 

 

 

 

 

 

 

[`Ent] Event

 

 

 

 

 

 

 

 

 

[`o;Ct]

Digital Output (5 or 6)

 

 

[`Ftb] Fixed Time Base

Fixed Time

Direction is set to Out-

[ o.Ct]

Control

 

 

 

[`utb] Variable Time Base

Base

put.

 

Set the output control type. This param-

 

 

 

 

 

eter is only used with PID control, but can

 

 

 

 

 

be set anytime.

 

 

 

 

 

 

 

 

 

 

 

 

[`o;tb]

Digital Output (5 or 6)

 

 

0.1 to 60.0 seconds (solid-

0.1 sec. [SSR &

Control is set to Fixed

[ o.tb]

Time Base

 

 

 

state relay or switched dc)

sw dc]

Time Base.

 

Set the time base for fixed-time-base con-

 

5.0 to 60.0 seconds (mechani-

20.0 sec.

 

 

trol.

 

 

 

cal relay or no-arc power

[mech, relay,

 

 

 

 

 

 

control)

no-arc]

 

 

 

 

 

 

 

 

[`o;Lo]

Digital Output (5 or 6)

 

 

0.0 to 100.0%

0.0%

Direction is set to Output

[ o.Lo]

Low Power Scale

 

 

 

 

and Source is set to

 

The power output will never be less than

 

 

 

Heat or Cool.

 

the value specified and will represent the

 

 

 

 

 

value at which output scaling begins.

 

 

 

 

 

 

 

 

 

 

 

 

[`o;hi]

Digital Output (5 or 6)

 

 

0.0 to 100.0%

100.0%

Direction is set to Output

[ o.hi]

High Power Scale

 

 

 

 

and Source is set to

 

The power output will never be greater

 

 

 

Heat or Cool.

 

than the value specified and will represent

 

 

 

 

 

the value at which output scaling stops.

 

 

 

 

 

 

 

 

 

 

 

[``Fi]

Digital Output (5 or 6)

 

 

1 to 4

None

Direction is set to Out-

[ Fi]

Function Instance

 

 

 

 

put, and there is more

 

Select which source instance will drive the

 

 

 

than one instance of the

 

output.

 

 

 

 

 

Function selection.

 

 

 

 

 

 

 

 

Note: Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces. If there is only one instance of a menu, no submenus will appear.

Watlow EZ-ZONE®PM Integrated Controller

• 35 •

Chapter 6 Setup Page